Home › Engine / Hybrid System › M15A-FKS (STARTING) › STARTER (w/ Stop And Start System) › from 2020.07
RM36W0E _51 Engine / Hybrid System _089409 M15A-FKS STARTING _0432160 STARTER(w/ Stop And Start System) A

M15A-FKS STARTING  STARTER(w/ Stop And Start System)  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE WIRE HARNESS

a.
A469408C01
0.26,0.948 0.594,0.948 false 0.26,0.313 0.5,0.313 false 0.104,0.865 0.417,1.021 0.313,0.156 10 false *1 0.115,0.219 0.427,0.375 0.313,0.156 10 false *a
*1 Wire Harness
*a Nut


Remove the 2 nuts and wire harness from the starter assembly.


Hide 28249 2.REMOVE STARTER INRUSH CURRENT REDUCTION RELAY

a.
A469409

Remove the 2 bolts and starter inrush current reduction relay from the starter drive housing assembly.


Hide 28226B 3.REMOVE REPAIR SERVICE STARTER KIT

a.
A469410

While holding the repair service starter kit to the starter drive housing assembly, remove the 2 nuts.


b.
A469411C01
1.104,2.521 1.708,2.521 true 1.792,2.448 2.104,2.604 0.313,0.156 10 false *a
*a Terminal C


While lifting the rear of the magnet starter switch assembly, disconnect it from terminal C.


c.
A469412C01
1.302,1.417 1.302,1.219 1.302,1.219 1.563,1.083 false 1.313,0.542 1.667,0.542 false 1.708,0.448 2.021,0.604 0.313,0.156 10 false *a 1.24,1.448 1.552,1.604 0.313,0.156 10 false *b
*a Pinion Drive Lever
*b Hook


While lifting the rear of the magnet starter switch assembly, remove the hook from the pinion drive lever, and then remove the magnet starter switch assembly.


Hide 28120 4.REMOVE STARTER YOKE ASSEMBLY

a.
A430874

Remove the 3 through bolts and pull out the starter yoke assembly together with the starter commutator end frame assembly.


Hide 5.REMOVE STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A248647C01
1.583,0.281 1.792,0.281 1.792,0.281 1.969,0.49 false 1.458,1.719 1.635,2.042 1.635,2.042 1.823,2.042 false 1.896,1.938 2.208,2.094 0.313,0.156 10 false *1 1.396,0.167 1.708,0.323 0.313,0.156 10 false *2
*1 Starter Yoke Assembly
*2 Starter Commutator End Frame Assembly


Remove the starter commutator end frame assembly from the starter yoke assembly.


Hide 6.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A430875C01
1.146,0.677 1.604,0.677 false 2.188,3 2.646,3 false 0.813,1.229 0.99,1.229 0.99,1.229 1.688,1.885 false 0.792,2.198 1.25,2.198 false 0.635,2.115 0.948,2.271 0.313,0.156 10 false *1 2.677,2.917 2.99,3.073 0.313,0.156 10 false *2 0.656,1.156 0.969,1.313 0.313,0.156 10 false *3 0.969,0.583 1.281,0.74 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*2 Starter Brush Holder Assembly
*3 Starter Armature Assembly
*a Hammer


Remove the starter yoke assembly while holding down the starter armature assembly and starter brush holder assembly with the handle of a hammer.

HINT:

The starter armature assembly will be attracted by the magnetic field of the starter yoke assembly. Hold the starter armature assembly with the handle of the hammer.



Hide 28160 7.REMOVE STARTER ARMATURE ASSEMBLY

a.
A248650C01
0.354,0.438 0.542,0.438 0.542,0.438 0.781,0.719 false 1.896,1.458 2.156,1.875 2.156,1.875 2.375,1.875 false 2.448,1.76 2.76,1.917 0.313,0.156 10 false *1 0.146,0.323 0.458,0.479 0.313,0.156 10 false *2
*1 Starter Armature Assembly
*2 Starter Brush Holder Assembly


Remove the starter armature assembly from the starter brush holder assembly.


Hide 28021 8.REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A469413

Remove the rubber seal from the starter drive housing assembly.


b.
A469414C01
1.969,0.313 2.521,0.313 false 2.719,1.177 2.865,0.896 2.865,0.896 3.031,0.896 false 3.094,0.833 3.365,1.052 0.271,0.219 10 false *1 2.625,0.25 2.938,0.406 0.313,0.156 10 false *2
*1 Starter Center Bearing Clutch Sub-assembly
*2 Starter Drive Housing Assembly


Remove the starter center bearing clutch sub-assembly from the starter drive housing assembly.