Home › Engine / Hybrid System › M15A-FKS (STARTING) › STARTER (w/ Stop And Start System) › from 2020.07
RM36W0E _51 Engine / Hybrid System _089409 M15A-FKS STARTING _0432160 STARTER(w/ Stop And Start System) G

M15A-FKS STARTING  STARTER(w/ Stop And Start System)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a no-load performance test.

i.
A469415C02
2.271,0.646 2.542,0.365 false 2.479,2.354 2.656,2.354 2.656,2.354 3.031,1.542 false 2.625,0.24 2.938,0.438 0.313,0.198 10 false *a 2.24,2.26 2.552,2.458 0.313,0.198 10 false *1
*1 Terminal 50
*a Starter Body
V100135

Moves outward


Connect a battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

NOTICE:

If the positive (+) and negative (-) leads are connected incorrectly, the IC inside the starter inrush current reduction relay will be damaged. Be sure to connect them correctly.


If the result is not as specified, replace the magnet starter switch assembly


ii.
A469416C01
2.49,2.458 2.656,2.458 2.656,2.458 3.01,1.531 false 2.292,0.646 2.552,0.406 false 2.25,2.385 2.563,2.583 0.313,0.198 10 false *1 2.646,0.281 2.958,0.479 0.313,0.198 10 false *a
*1 Terminal 50
*a Starter Body
V113147

Disconnect
V100135

Returns inward


While maintaining the battery connections of the pull-in test, disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.

If the result is not as specified, replace the magnet starter switch assembly.


iii.

Secure the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter assembly is secured in the vise to prevent it from falling out.



iv.

Connect the battery and an ammeter to the starter assembly as shown in the illustration.

A469417C01
0.896,2.25 1.073,2.25 1.073,2.25 1.313,1.833 true 2.094,1.406 2.563,0.688 2.563,0.688 2.76,0.688 true 3.083,2.083 3.417,2.083 false 0.656,2.135 0.969,2.333 0.313,0.198 10 false *1 2.833,0.594 3.146,0.792 0.313,0.198 10 false *2 3.521,2 3.833,2.198 0.313,0.198 10 false *3
*1 Terminal 50 *2 Terminal 30
*3 Starter Body - -
V100135

Rotates - -


NOTICE:

Do not allow any lead to get caught as the clutch pinion gear operates.



v.

Check that the starter assembly operates smoothly and steadily while the clutch pinion gear is moving outward. Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive
(+) terminal -
Terminal 30 -
Terminal 50
11.5 V Below 90 A


If the result is not as specified, repair or replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.
A224239C01
2.26,1.167 2.885,1.094 2.885,1.094 2.354,0.958 false 2.917,1.021 3.229,1.219 0.313,0.198 10 false *a
*a Segment


Check the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



b.
A224240C01
0.792,1.302 1.073,1.302 1.073,1.302 1.604,0.896 false 2.302,1.198 2.615,0.542 2.615,0.542 2.833,0.542 true 2.885,0.458 3.198,0.656 0.313,0.198 10 false *a 0.563,1.219 0.875,1.417 0.313,0.198 10 false *b
*a Segment
*b Starter Armature Core


Check the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter armature core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.

Check the commutator appearance.

If the surface is dirty or burnt, replace the starter armature assembly.


d.
A037025C12
0.365,0.635 0.552,0.635 0.552,0.635 0.875,0.833 false 2.052,1.417 2.604,1.698 2.604,1.698 2.823,1.698 true 0.208,0.542 0.427,0.698 0.219,0.156 10 false *a 2.844,1.604 3.063,1.76 0.219,0.156 10 false *a
*a Armature Shaft


Check the commutator for runout.

i.

Place the armature shaft on V-blocks.


ii.

Using a dial indicator, measure the runout.

Maximum Runout:

0.05 mm (0.00197 in.)


If the runout is greater than the maximum, replace the starter armature assembly.



e.
A062221C05
0.167,0.063 0.479,0.219 0.313,0.156 10 false *a
*a Diameter


Using a vernier caliper, measure the commutator diameter.

Standard Diameter (convex part):

29 mm (1.1417 in.)


Minimum Diameter (convex part):

28 mm (1.1024 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A062222C05
2.667,0.479 2.979,0.635 0.313,0.156 10 false *a
*a Undercut Depth


Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard Undercut Depth (convex part):

0.7 mm (0.0276 in.)


Minimum Undercut Depth (convex part):

0.4 mm (0.0157 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.


Hide 28140 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
A204349C04
2.74,0.219 3.052,0.375 0.313,0.156 10 *a
*a Length


Check the brush length.

i.

Using a vernier caliper, measure the brush length.

Standard Length (convex part):

11.6 mm (0.457 in.)


Minimum Length (convex part):

7.6 mm (0.299 in.)


If the length is less than the minimum, replace the starter brush holder assembly.



Hide 28021 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A439288

Install the starter armature assembly to the starter center bearing clutch sub-assembly.


b.
A433409C02
2.042,0.646 2.208,0.802 0.167,0.156 10 false *a 2,1.74 2.156,1.906 0.156,0.167 10 true *b
*a Free
*b Lock


Hold the starter armature assembly, rotate the clutch pinion gear clockwise, and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks. If the clutch pinion gear does not operate as specified, replace the starter center bearing clutch sub-assembly.


Hide 28226B 5.INSPECT REPAIR SERVICE STARTER KIT

A033580

a.

Check the plunger.

i.

Push in the plunger and check that it returns quickly to its original position.

NOTICE:
·

Do not drop the plunger.

·

To avoid damaging the inside of the magnet switch, do not release the plunger quickly.



If the plunger does not operate as specified, replace the repair service starter kit.



b.
A430881C05
2.25,1 2.583,0.667 2.583,0.667 2.75,0.667 true 1.25,0.75 1.083,0.333 1.083,0.333 0.917,0.333 true 0.75,0.26 1.063,0.417 0.313,0.156 10 false *a 2.854,0.583 3.167,0.74 0.313,0.156 10 false *b
*a Magnet Starter Switch Assembly Body
*b Terminal 50


Check the repair service starter kit resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - magnet starter switch assembly body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.