Home › Engine / Hybrid System › M15A-FKS (STARTING) › STARTER (w/ Stop And Start System) › from 2020.07
RM36W0E _51 Engine / Hybrid System _089409 M15A-FKS STARTING _0432160 STARTER(w/ Stop And Start System) A

M15A-FKS STARTING  STARTER(w/ Stop And Start System)  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A247255C11
0,0 0,0 false
V100135

High-temperature Grease


Apply high-temperature grease to the pinion drive lever.

HINT:

Apply approximately 0.1 g of high-temperature grease to each section.



b.
A469418C01
1.344,0.635 2.094,0.385 2.094,0.385 2.26,0.385 true 1.573,1.938 1.833,1.938 1.833,1.938 2.104,1.271 true 2.344,0.292 2.656,0.448 0.313,0.156 10 false *a 1.406,1.854 1.719,2.01 0.313,0.156 10 false *b
*a Cutout
*b Protrusion


Align the cutout of the starter drive housing assembly with the protrusion of the starter center bearing clutch sub-assembly and install the starter center bearing clutch sub-assembly.


c.
A469413

Install the rubber seal to the starter drive housing assembly.


Hide 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A248658

Install the starter commutator end frame assembly to the starter brush holder assembly as shown in the illustration.

HINT:

If the parts are not aligned correctly, the through bolt cannot be attached.



b.
A248796

Spread the brushes on the starter brush holder assembly, and install the starter armature assembly to the starter brush holder assembly.


Hide 28160 3.INSTALL STARTER ARMATURE ASSEMBLY

a.
A430883C01
1.188,0.771 1.594,0.771 false 0.875,1.24 1.094,1.24 1.094,1.24 1.656,1.823 true 0.844,2.167 1.25,2.167 false 1.969,3.063 2.375,3.063 false 0.688,2.083 1,2.24 0.313,0.156 10 false *1 2.417,2.99 2.729,3.146 0.313,0.156 10 false *2 0.708,1.156 1.021,1.313 0.313,0.156 10 false *3 1.021,0.677 1.333,0.833 0.313,0.156 10 false *a
*1 Starter Yoke Assembly
*2 Starter Brush Holder Assembly
*3 Starter Armature Assembly
*a Hammer


Install the starter yoke assembly while holding down the starter armature assembly and starter brush holder assembly with the handle of a hammer.

HINT:

The starter armature assembly will be attracted by the magnetic field of the starter yoke assembly. Hold the starter armature assembly with the handle of the hammer.



Hide 4.INSTALL STARTER YOKE ASSEMBLY

a.
A430884C01
0.927,0.771 1.156,0.219 1.156,0.219 1.385,0.219 false 1.385,0.792 1.698,1.688 1.698,1.688 1.917,1.688 true 1.406,0.146 1.719,0.302 0.313,0.156 10 false *a 1.938,1.615 2.25,1.771 0.313,0.156 10 false *b
*a Protrusion
*b Cutout


Align the cutout of the starter yoke assembly with the protrusion of the starter center bearing clutch sub-assembly.


b.
A430874

Install the starter yoke assembly with the 3 through bolts.

Torque:
3.2 N*m (33 kgf*cm, 28 in.*lbf)


Hide 28226B 5.INSTALL REPAIR SERVICE STARTER KIT

a.
A469411C02
1.104,2.573 1.708,2.573 true 1.792,2.49 2.104,2.646 0.313,0.156 10 false *a
*a Terminal C


Hang the hook of the magnet starter switch assembly on the pinion drive lever.

NOTICE:
·

Connect the magnet starter switch assembly securely to terminal C.

·

Check that the parts are free of foreign matter, oil or grease.




b.

Install the magnet starter switch assembly with the 2 nuts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


Hide 28249 6.INSTALL STARTER INRUSH CURRENT REDUCTION RELAY

A469409

a.

Install the starter inrush current reduction relay to the starter drive housing assembly with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 7.INSTALL WIRE HARNESS

a.
A469408C02
0.281,0.302 0.531,0.302 false 0.375,0.938 0.625,0.938 false 0.188,0.844 0.5,1 0.313,0.156 10 false *1 0.115,0.198 0.427,0.354 0.313,0.156 10 false *a
*1 Wire Harness
*a Nut


Install the wire harness to the starter assembly with the 2 nuts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)