Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2020.07–2020.09
RM36W0E _59 Vehicle Exterior _088063 WIPER / WASHER _0420505 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Read the Data List according to the display on the GTS.



Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper Motor Cam Switch 1 Windshield wiper motor cam signal OFF or ON OFF: Front wiper motor stop
ON: Front wiper motor operation
-
Wiper Control Switch HI Front wiper switch HI position signal OFF or ON OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position
-
Communication Wiper ECU Connection status between windshield wiper motor assembly and main body ECU (multiplex network body ECU) STOP or OK STOP: Not Connected
OK: Connected
Although this item is displayed on the GTS, it is not applicable to this vehicle.
Communication Wiper Module Connection status between windshield wiper relay assembly and main body ECU (multiplex network body ECU) STOP or OK STOP: Not Connected
OK: Connected
DTCs are stored if a malfunction occurs in the CXPI communication system.
Communication Humidity/Rain Sensor Connection status between rain sensor and main body ECU (multiplex network body ECU) STOP or OK STOP: Not Connected
OK: Connected
Although this item is displayed on the GTS, it is not applicable to this vehicle.
R Wiper Stop Function at Back Door/Trunk Lid Open Function to enable the back door open linked rear wiper suspend function Enable or Disable Customize setting displayed -
Rear Wiper Washer Function Function to enable the rear washer linked rear wiper operation function Enable or Disable Customize setting displayed -
Rear Wiper with Reverse Setting Function to enable the R shift position linked rear wiper operation function Disable, 1 time, Continuation Customize setting displayed -
Wiper Power Relay Wiper relay position signal OFF or ON OFF: WIPER relay off
ON: WIPER relay on
-
Front Washer Relay Front washer operation OFF or ON OFF: Front washer switch off
ON: Front washer switch ON
-
Front Wiper Lo Operation Windshield wiper motor assembly LO operation OFF or ON OFF: Front wiper motor stopped
ON: During front wiper motor LO operation
-
Front Wiper Hi Operation Windshield wiper motor assembly HI operation OFF or ON OFF: Front wiper motor stopped
ON: During front wiper motor HI operation
-
Rear Washer Relay Rear washer operation OFF or ON OFF: Rear washer switch off
ON: Rear washer switch ON
-
Rear Wiper Operation Rear wiper operation OFF or ON OFF: Rear wiper motor stopped
ON: During rear wiper motor LO operation
-
Chassis > Steering Angle Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Wiper OFF Switch Front wiper switch OFF position signal OFF or ON OFF: Front wiper switch not in OFF position
ON: Front wiper switch in OFF position
-
Wiper Auto/Int Switch Front wiper switch or INT position signal OFF or ON OFF: Front wiper switch not in or INT position
ON: Front wiper switch in INT position
-
Wiper Lo Switch Front wiper switch LO position signal OFF or ON OFF: Front wiper switch not in LO position
ON: Front wiper switch in LO position
-
Wiper Hi Switch Front wiper switch HI position signal OFF or ON OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position
-
Wiper Mist Switch Front wiper switch MIST position signal OFF or ON OFF: Front wiper switch not in MIST position
ON: Front wiper switch in MIST position
-
Washer Switch Washer switch Fr WASH position signal OFF or ON OFF: Washer switch not in Fr WASH position
ON: Washer switch in Fr WASH position
-
Rear Wiper INT Switch Rear wiper switch Rr INT position signal OFF or ON OFF: Rear wiper switch not in Rr INT position
ON: Rear wiper switch in Rr INT position
-
Rear Wiper ON Switch Rear wiper switch Rr ON position signal OFF or ON OFF: Rear wiper switch not in Rr ON position
ON: Rear wiper switch in Rr ON position
-
Rear Washer Switch Washer switch Rr WASH position signal OFF or ON OFF: Washer switch not in Rr WASH position
ON: Washer switch in Rr WASH position
-
Intermittent Time Volume (Shortest) Intermittent time adjustment switch condition OFF or ON OFF: Washer switch not in P4 position
ON: Washer switch in P4 position
Although this item is displayed on the GTS, it is not applicable to this vehicle.
Intermittent Time Volume (Shorter) Intermittent time adjustment switch condition OFF or ON OFF: Washer switch not in P3 position
ON: Washer switch in P3 position
Although this item is displayed on the GTS, it is not applicable to this vehicle.
Intermittent Time Volume (Longer) Intermittent time adjustment switch condition OFF or ON OFF: Washer switch not in P2 position
ON: Washer switch in P2 position
Although this item is displayed on the GTS, it is not applicable to this vehicle.
Intermittent Time Volume (Longest) Intermittent time adjustment switch condition OFF or ON OFF: Washer switch not in P1 position
ON: Washer switch in P1 position
Although this item is displayed on the GTS, it is not applicable to this vehicle.
Wiper Spec Info Function information Unknown, Auto spec or Int spec Unknown: Specification not stored
Auto spec: w/ Auto wiper system
Int spec: w/o Auto wiper system
-
Body Electrical > Rain and/or Humidity Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sensor Info Rain sensor temperature circuit condition OK or NG OK: Rain sensor is normal
NG: Malfunction in rain sensor thermistor
-
Sensor Reaction Info Rain sensor output condition OK or NG OK: Rain sensor is normal
NG: Malfunction in rain sensor thermistor output
-
Sensor High Temp Info Rain sensor high temperature condition OK or NG OK: Rain sensor is normal
NG: Rain sensor temperature is high
-
Sensor Low Temp Info Rain sensor low temperature condition OK or NG OK: Rain sensor is normal
NG: Rain sensor temperature is low
-
Wiper Switch Auto Signal Windshield wiper switch assembly (AUTO position) condition OFF or ON OFF: Windshield wiper switch assembly not in AUTO position
ON: Windshield wiper switch assembly in AUTO position
-
Intermittent Time Volume Auto sensitivity adjustment switch condition Shortest, Shorter, Longer or Longest Shortest: P4
Shorter: P3
Longer: P2
Longest: P1
*1
Wiper Type Displays vehicle wiper type Normal, Reversing (1 Motor) or Reversing (2 Motor) Shows vehicle wiper type -
Wiper Stop Position Windshield wiper motor assembly stop position Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos Store Area/Lower Rev Pos: Lower reverse position or lower
Wipe Area: Between lower reverse position and upper reverse position
Upper Rev Pos: Upper reverse position
Although this item is displayed on the GTS, it is not applicable to this vehicle.
Wiper Stop Position (Sub Motor) No. 2 Windshield wiper motor assembly stop position Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos Store Area/Lower Rev Pos: Lower reverse position or lower
Wipe Area: Between lower reverse position and upper reverse position
Upper Rev Pos: Upper reverse position
Although this item is displayed on the GTS, it is not applicable to this vehicle.
Motor Status Wiper motor control condition in response to rain sensor request Normal, Normal (Link Ctrl), Normal (Req Deny), Abnormal or Normal (Wiper Ctrl) Current motor control condition -
Wiping Mode Signal (Sensor to Wiper) Status of command request signal for front wiper speed and intermittent time from rain sensor Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (rain not detected)
LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested
HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested
INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s
INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s
INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s
INT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s
INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s
INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s
INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s
INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s
INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s
INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s
INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s
INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s
INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s
INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s
INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested
OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization)
Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction)
-
Wiper LO Single Operation Signal Wiper LO Single Operation Signal ON or OFF ON: Windshield wiper switch assembly in AUTO position and sensor determines small amount of rain while wiper is in stopped position
OFF: Windshield wiper switch assembly in AUTO position and wiper in position other than stopped
-
Wiping Mode Signal (Wiper to Sensor) Response status of command request signal for front wiper speed and intermittent time from rain sensor to windshield wiper relay assembly Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (rain not detected)
LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested
HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested
INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s
INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s
INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s
INT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s
INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s
INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s
INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s
INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s
INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s
INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s
INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s
INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s
INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s
INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s
INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested
OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization)
Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction)
-
Sensor High Temp History History of if the rain sensor temperature being high (approximately 80°C (176°F)) OFF or ON OFF: The rain sensor temperature has not been (approximately 80°C (176°F))
ON: The rain sensor temperature reached high (approximately 80°C (176°F))
Clearing the DTCs also clears the history
Sensor Low Temp History History of if the rain sensor temperature being low (approximately -40 °C (-104°F)) OFF or ON OFF: The rain sensor temperature has not been low (approximately -40°C (-104°F))
ON: The rain sensor temperature reached low (approximately -40°C (-104°F))
Clearing the DTCs also clears the history
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -
Auto Wiper Setting to switch control between automatic wipers/vehicle speed sensing intermittent time adjustment Avail or Not Avl Almost the same as actual vehicle speed -
Number of Trouble Code Number of DTCs 0 to 255 Number of stored DTCs displayed -

*1: Refer to Inspection for each position of the switch.

Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>INSPECTION


ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wiper Power Relay Function to operate the WIPER relay OFF or ON -
Front Washer Relay Function to operate the windshield washer motor and pump assembly (Front) OFF or ON -
Front Wiper Lo Operation Function to operate the windshield wiper motor assembly in LO OFF or ON -
Front Wiper Hi Operation Function to operate the windshield wiper motor assembly in HI OFF or ON -
Rear Washer Relay Function to operate the windshield washer motor and pump assembly (Rear) OFF or ON -
Rear Wiper Operation Function to operate the rear wiper motor assembly OFF or ON -