When the manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release with bearing cylinder assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.
35150D
1.INSTALL TRANSMISSION CASE PLUG ASSEMBLY
Perform this procedure only when replacement of the manual transaxle assembly is necessary.
Coat the O-ring of a new transmission case plug assembly with gear oil.
Install the transmission case plug assembly to the front transaxle case.
2.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the manual transmission case with the bolt.
Install the wire harness clamp brackets to the front transaxle (MTM) case with the 2 bolts.
87121V
3.INSTALL HEATER BRACKET
Install the heater bracket to the manual transmission case with the bolt.
31400
4.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY
31407B
5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
6.INSPECT CLUTCH PIPE LINE
31407B
7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
31484
8.INSTALL CLUTCH FLEXIBLE HOSE BRACKET
Install the clutch flexible hose bracket to the manual transmission case with the bolt.
31483
9.INSTALL BLEEDER CLUTCH RELEASE TUBE
12364B
10.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
Install the No. 2 engine moving control rod to the front transaxle case with the 4 bolts in the order shown in the illustration.
51201
11.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Install the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.
30300
12.INSTALL MANUAL TRANSAXLE ASSEMBLY
| *1 | Knock Pin |
Check that the 2 knock pins are installed on the engine assembly before installing the manual transaxle assembly.
Align the input shaft with the clutch disc and install the engine assembly to the manual transaxle assembly.
Make sure that the wire harness or similar items are not pinched between the contact surfaces.
Do not forcibly pry on the manual transaxle assembly when installing it to the engine assembly.
Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.
Make sure that the knock pins fit securely into the holes when installing the manual transaxle assembly to the engine assembly.
Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.
Temporarily install the bolt (A).
Bolt (A): Install from the manual transaxle assembly side.
Install the bolt (B), then fully tighten the bolt (A).
Bolt (B): Install from the manual transaxle assembly side.
Install the bolts (C).
Bolt (C): Install from the manual transaxle assembly side.
Install the 4 bolts (D).
Bolt (D): Install from the engine assembly side.
43409E
13.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
| *a | Temporarily Tighten |
Install the drive shaft heat insulator sub-assembly to the manual transmission case with the 2 bolts in the order shown in the illustration.
14.CONNECT ENGINE WIRE
Engage the 3 clamps.
Engage the 3 clamps.
| *a | Neutral Position Switch Connector |
Connect the neutral position switch connector.
Engage the 3 clamps.
Install the 3 bolts.
Engage the clamp.
| *a | Back-up Light Switch Assembly Connector |
Connect the back-up light switch assembly connector.
28100
15.INSTALL STARTER ASSEMBLY
16.REMOVE ENGINE HANGERS
17.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
18. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART