Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › INPUT SHAFT › from 2020.07
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432180 INPUT SHAFT G

C551 MANUAL TRANSMISSION / TRANSAXLE  INPUT SHAFT  INSPECTION  


PROCEDURE

Hide 33333 1.INSPECT 3RD GEAR THRUST CLEARANCE

a.
G021219

Using a feeler gauge, measure the 3rd gear thrust clearance.

Standard clearance:

0.10 to 0.35 mm (0.0039 to 0.0138 in.)

Maximum clearance:

0.35 mm (0.0138 in.)


If the clearance is more than the maximum, replace the No. 2 transmission clutch hub, 3rd gear or input shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33336 2.INSPECT 5TH GEAR THRUST CLEARANCE

a.
G021220

Using a dial indicator, measure the 5th gear thrust clearance.

Standard clearance:

0.10 to 0.50 mm (0.0039 to 0.0197 in.)

Maximum clearance:

0.50 mm (0.0197 in.)


If the clearance is more than the maximum, replace the No. 3 transmission clutch hub, 5th gear or 5th thrust washer. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33333 3.INSPECT 3RD GEAR RADIAL CLEARANCE

a.
G021221

Using a dial indicator, measure the 3rd gear radial clearance.

Standard clearance:

0.015 to 0.058 mm (0.0006 to 0.0023 in.)

Maximum clearance:

0.058 mm (0.0023 in.)


If the clearance is more than the maximum, replace the 3rd gear, 3rd gear needle roller bearing or input shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33334 4.INSPECT 4TH GEAR RADIAL CLEARANCE

a.
G021222

Using a dial indicator, measure the 4th gear radial clearance.

Standard clearance:

0.015 to 0.058 mm (0.0006 to 0.0023 in.)

Maximum clearance:

0.058 mm (0.0023 in.)


If the clearance is more than the maximum, replace the 4th gear, 4th gear needle roller bearing or input shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33336 5.INSPECT 5TH GEAR RADIAL CLEARANCE

a.
G021223

Using a dial indicator, measure the 5th gear radial clearance.

Standard clearance:

0.015 to 0.058 mm (0.0006 to 0.0023 in.)

Maximum clearance:

0.058 mm (0.0023 in.)


If the clearance is more than the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33334 6.INSPECT 4TH GEAR THRUST CLEARANCE

a.
G021228

Using a dial indicator, measure the 4th gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.0039 to 0.0217 in.)

Maximum clearance:

0.55 mm (0.0217 in.)


If the clearance is more than the maximum, replace the No. 2 transmission clutch hub, 4th gear or 5th thrust washer. Replace the part or parts determined to be the most likely cause of the problem.


Hide 33311 7.INSPECT INPUT SHAFT

a.

Check the input shaft for wear and damage.


b.
G021244

Using a dial indicator, check the input shaft runout.

Maximum runout:

0.03 mm (0.0012 in.)


If the runout exceeds the maximum, replace the input shaft.


c.
U161415E02
0.281,0.375 0.417,0.573 0.135,0.198 10 false A 0.604,0.333 0.729,0.531 0.125,0.198 10 false B 0.875,0.323 1.01,0.542 0.135,0.219 10 false C 1.26,0.313 1.406,0.51 0.146,0.198 10 false D 2.083,0.354 2.219,0.552 0.135,0.198 10 false E 2.188,1.458 2.323,1.667 0.135,0.208 10 false F

Using a micrometer, measure the outer diameter of the input shaft journal surface, at the locations indicated.

Standard outer diameter:
Part A:

25.502 to 25.515 mm (1.0040 to 1.0045 in.)

Part B:

30.985 to 31.000 mm (1.2199 to 1.2205 in.)

Part C and D:

33.985 to 34.000 mm (1.3380 to 1.3386 in.)

Part E:

23.002 to 23.015 mm (0.9056 to 0.9061 in.)

Part F:

22.967 to 23.000 mm (0.9042 to 0.9055 in.)


If the outer diameter is less than the minimum, replace the input shaft.

If the outer diameters are below the minimums, replace the input shaft.


Hide 33333 8.INSPECT 3RD GEAR

a.
G021246

Using a cylinder gauge, measure the inside diameter of the 3rd gear.

Standard inside diameter:

39.015 to 39.031 mm (1.5360 to 1.5367 in.)


Maximum inside diameter:

39.031 mm (1.5367 in.)


If the inside diameter is more than the maximum, replace the 3rd gear.


Hide 33334 9.INSPECT 4TH GEAR

a.
G021246

Using a cylinder gauge, measure the inside diameter of the 4th gear.

Standard inside diameter:

39.015 to 39.031 mm (1.5360 to 1.5367 in.)


Maximum inside diameter:

39.031 mm (1.5367 in.)


If the inside diameter is more than the maximum, replace the 4th gear.


Hide 33336 10.INSPECT 5TH GEAR

a.
G021246

Using a cylinder gauge, measure the inside diameter of the 5th gear.

Standard inside diameter:

36.015 to 36.031 mm (1.4180 to 1.4185 in.)


Maximum inside diameter:

36.031 mm (1.4185 in.)


If the inside diameter is more than the maximum, replace the 5th gear.


Hide 33368G 11.INSPECT 3RD GEAR SYNCHRONIZER RING

a.

Check for wear and damage.


b.

Coat the 3rd gear cone with gear oil.


c.
G021238

Turn the 3rd gear synchronizer ring in both directions while pushing it against the 3rd gear cone and check that it locks in both directions. If the 3rd gear synchronizer ring does not lock, replace the 3rd gear synchronizer ring.


d.
G021239

Using a feeler gauge, measure the clearance between the 3rd gear synchronizer ring back and the 3rd gear spline end.

Standard clearance:

0.75 to 1.65 mm (0.030 to 0.064 in.)


Minimum clearance:

0.75 mm (0.030 in.)


If the clearance is less than the minimum, replace the 3rd gear synchronizer ring.


Hide 33368H 12.INSPECT 4TH GEAR SYNCHRONIZER RING

a.

Check for wear and damage.


b.

Coat the 4th gear cone with gear oil.


c.
G021238

Turn the 4th gear synchronizer ring in both directions while pushing it against the 4th gear cone and check that it locks in both directions. If the 4th gear synchronizer ring does not lock, replace the 4th gear synchronizer ring.


d.
G021239

Using a feeler gauge, measure the clearance between the 4th gear synchronizer ring back and the 4th gear spline end.

Standard clearance:

0.75 to 1.65 mm (0.030 to 0.064 in.)


Minimum clearance:

0.75 mm (0.030 in.)


If the clearance is less than the minimum, replace the 4th gear synchronizer ring.


Hide 33368J 13.INSPECT 5TH GEAR SYNCHRONIZER RING

a.

Check for wear and damage.


b.

Coat the 5th gear cone with gear oil.


c.
G021238

Turn the 5th gear synchronizer ring in both directions while pushing it against the 5th gear cone and check that it locks in both directions. If the 5th gear synchronizer ring does not lock, replace the 5th gear synchronizer ring.


d.
G021239

Using a feeler gauge, measure the clearance between the 5th synchronizer ring back and the 5th gear spline end.

Standard clearance:

0.75 to 1.65 mm (0.030 to 0.064 in.)


Minimum clearance:

0.75 mm (0.030 in.)


If the clearance is less than the minimum, replace the 5th gear synchronizer ring.


Hide 33364 14.INSPECT NO. 2 TRANSMISSION HUB SLEEVE

a.
G021241E03
2.76,0.375 3.01,0.615 0.25,0.24 10 false A 2.802,1.271 3.031,1.552 0.229,0.281 10 false B

Using a vernier caliper, measure the width of the No. 2 transmission hub sleeve groove (A) and the thickness of the claw part on the No. 2 gear shift fork (B), and then calculate the clearance.

Standard clearance (A-B):

0.15 to 0.35 mm (0.0059 to 0.0138 in.)


If the clearance is not as specified, replace the No. 2 transmission hub sleeve and No. 2 gear shift fork.


Hide 33395 15.INSPECT NO. 3 TRANSMISSION HUB SLEEVE

a.
G021243E03
3.073,0.427 3.188,0.625 0.115,0.198 10 false A 3.073,1.177 3.188,1.375 0.115,0.198 10 false B

Using a vernier caliper, measure the width of the No. 3 transmission hub sleeve groove (A) and the thickness of the claw part on the No. 3 gear shift fork (B), and then calculate the clearance.

Standard clearance (A-B):

0.15 to 0.35 mm (0.0059 to 0.0138 in.)


If the clearance is not as specified, replace the No. 3 transmission hub sleeve and No. 3 gear shift fork.