Home › Drivetrain › C551 (MANUAL TRANSMISSION / TRANSAXLE) › SHIFT AND SELECT LEVER SHAFT › from 2020.07
RM36W0E _52 Drivetrain _091208 C551 MANUAL TRANSMISSION / TRANSAXLE _0432182 SHIFT AND SELECT LEVER SHAFT A

C551 MANUAL TRANSMISSION / TRANSAXLE  SHIFT AND SELECT LEVER SHAFT  REASSEMBLY  


PROCEDURE

Hide 33528C 1.INSTALL CONTROL SHAFT COVER OIL SEAL

a.

Coat the lip of a new control shaft cover oil seal with MP grease.


b.
D005800E01
0.687,1.527 0.425,1.1 0.425,1.1 0.7,1.315 false 0.051,1.004 0.390,1.151 0.339,0.147 10 SST

Using SST and a hammer, tap in the control shaft cover oil seal to the control shaft cover.

SST
09950-60010  (09951-00260)
09950-70010  (09951-07100)

Standard depth:

0 to 0.5 mm (0 to 0.0196 in.)


NOTICE:

Be careful not to damage the lip of the control shaft cover oil seal.



Hide 33262F 2.INSTALL SELECT LEVER SHAFT OIL SEAL

a.

Coat the lip of a new select lever shaft oil seal with MP grease.


b.
D005796E01
0.946,1.329 0.513,0.702 0.513,0.702 0.954,0.985 false 0.131,0.621 0.462,0.768 0.332,0.147 10 SST

Using SST and a hammer, tap in the select lever shaft oil seal to the control shaft cover.

SST
09950-60010  (09951-00240)
09950-70010  (09951-07100)

Standard depth:

2.0 to 2.5 mm (0.0788 to 0.0984 in.)


NOTICE:

Be careful not to damage the lip of the select lever shaft oil seal.



Hide 33261C 3.INSTALL SHIFT AND SELECT LEVER SHAFT

a.
C232578C03
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surface of the shift lever boot and install the shift lever boot to the shift and select lever shaft.


b.

Apply MP grease to the contact surfaces of the control shaft cover and shift and select lever shaft.


c.

Install the shift and select lever shaft together with the shift lever boot to the control shaft cover.

NOTICE:

Be careful not to damage the lip of the control shaft cover oil seal.



d.
F100235C04
0.792,0.334 1.102,0.609 false 0.596,0.205 0.869,0.439 0.273,0.235 10 *a
*a Rope or equivalent


Using a screwdriver and hammer, install a new snap ring to the shift and select lever shaft.

HINT:

Lifting the control shaft cover up with a piece of rope or the equivalent makes the work easier.



Hide 33256 4.INSTALL SELECT INNER LEVER

a.
C058753

Install the select inner lever to the control shaft cover.


Hide 33262E 5.INSTALL SELECT LEVER SHAFT

a.

Apply MP grease to the contact surfaces of the control shaft cover and select lever shaft.


b.
C245805

Install the select lever shaft to the control shaft cover and pass the select lever shaft through the select inner lever.

NOTICE:
·

Be careful not to damage the lip of the select lever shaft oil seal.

·

Fit the end of the select inner lever into the groove of the shift and select lever shaft as shown in the illustration.




c.

Clean and degrease the bolt and installation hole in the select lever shaft.


d.

Coat the threads of the bolt with adhesive and install it to the select inner lever.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



Hide 33277 6.INSTALL NO. 2 SELECT SPRING SEAT

a.
U161403C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the inner surface of the No. 2 select spring seat and shift and select lever shaft, and then install the No. 2 select spring seat to the shift and select lever shaft.


Hide 33276F 7.INSTALL SELECT RETURN COMPRESSION SPRING

a.
F100240

Install the select return compression spring to the shift and select lever shaft.


Hide 33293G 8.INSTALL LOCK BALL HOLDER

a.

Install the lock ball pin and spring to the lock ball holder.


b.
U161036

Install the lock ball holder to the shift interlock plate.


Hide 33251A 9.INSTALL INNER NO. 1 SHIFT LEVER (w/o Stop and Start System)

a.
C242618C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surfaces of the shift interlock plate and shift and select lever shaft.


b.
F100237

While pushing up the inner No. 1 shift lever so that the hole of the inner No. 1 shift lever aligns with the hole of the shift and select lever shaft, insert a 5 mm pin punch halfway into the inner No. 1 shift lever, and then using another 5 mm pin punch and a hammer, tap in the inner No. 1 shift lever slotted pin. When the inner No. 1 shift lever is fixed in place with the slotted spring pin, pull out the pin punch while holding the inner No. 1 shift lever.

Standard depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)



c.
D005790

Using a screwdriver and hammer, install a new snap ring to the shift and select lever shaft.


Hide 33251A 10.INSTALL INNER NO. 1 SHIFT LEVER (w/ Stop and Start System)

a.
C309305C01
0,0 0,0 false
V100135

MP grease


Apply MP grease to the contact surfaces of the shift interlock plate and shift and select lever shaft.


b.
C309306

While pushing up the inner No. 1 shift lever so that the hole of the inner No. 1 shift lever aligns with the hole of the shift and select lever shaft, insert a 5 mm pin punch halfway into the inner No. 1 shift lever, and then using another 5 mm pin punch and a hammer, tap in the inner No. 1 shift lever slotted pin. When the inner No. 1 shift lever is fixed in place with the slotted spring pin, pull out the pin punch while holding the inner No. 1 shift lever.

Standard depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)