Home › Power Source / Network › 1KR-FE (BATTERY / CHARGING) › GENERATOR (for 80A Type) › from 2020.07
RM36W0E _57 Power Source / Network _090846 1KR-FE BATTERY / CHARGING _0432212 GENERATOR(for 80A Type) A

1KR-FE BATTERY / CHARGING  GENERATOR(for 80A Type)  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A325004

Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.
A330710C01
1.25,0.26 1.531,0.26 1.531,0.26 1.917,0.708 false 2.823,1.823 2.823,1.083 false 2.031,2.344 2.281,2.802 2.281,2.802 2.521,2.802 false 1.073,0.146 1.385,0.302 0.313,0.156 10 false *a 2.656,1.885 3.208,2.094 0.552,0.208 10 false SST A 2.604,2.698 3.375,2.896 0.771,0.198 10 false SST A
*a Rotor Shaft


Place the rotor shaft end into SST (A).

SST
09820-70010  (09821-70010, 09822-70010)


c.
A330711C01
1.302,0.427 1.875,0.427 false 2.677,1.844 2.677,1.063 false 2.333,2.75 2.115,2.75 2.115,2.75 1.948,2.344 false 1.146,0.333 1.458,0.49 0.313,0.156 10 false *1 2.5,1.885 3.073,2.115 0.573,0.229 10 false SST B 2.406,2.646 2.979,2.875 0.573,0.229 10 false SST B
*1 Generator Pulley with Clutch


Fit SST (B) to the generator pulley with clutch.


d.
A330712C01
1.979,1.052 2.042,0.802 2.042,0.802 2.26,0.802 true 2.146,1.125 2.333,1 2.333,1 2.531,1 false 0.552,1.333 0.771,1.333 0.771,1.333 1.115,1.615 false 1.552,1.76 1.76,1.969 1.76,1.969 1.948,1.969 false 0.365,1.25 0.677,1.406 0.313,0.156 10 false *a 2.021,1.875 2.25,2.073 0.229,0.198 10 true *b 2.594,0.927 3.052,1.156 0.458,0.229 10 false SST A 2.302,0.719 2.76,0.948 0.458,0.229 10 false SST B
*a Turn
*b Hold


Loosen the generator pulley with clutch by turning SST (A) as shown in the illustration.

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.


·

Hold SST (B) tightly during the operation.




e.

Remove SST (A) and (B) from the generator pulley with clutch.


f.

Remove the generator pulley with clutch from the rotor shaft.


g.

Remove the generator assembly from the vise.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.
A153378

Place the generator assembly on the generator pulley with clutch.


b.
A325033

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 4.REMOVE GENERATOR TERMINAL INSULATOR

a.
A108428

Remove the generator terminal insulator from the generator coil assembly.


Hide 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A108418

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A325035

Remove the 4 bolts.


b.
A153383C18
1.063,1.802 0.99,1.802 0.99,1.802 0.635,1.573 false 2.667,0.688 2.563,0.688 2.563,0.688 2.094,0.854 false 1.115,1.719 1.406,1.875 0.292,0.156 10 false SST 2.719,0.604 3.01,0.75 0.292,0.146 10 false SST 2.823,0.094 3.135,0.25 0.313,0.156 10 false *a 0.615,0.563 0.927,0.719 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


c.
A284548

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove the broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A118367C02
0.646,0.375 0.979,0.375 0.979,0.375 1.208,0.74 false 2.365,1.604 2.604,1.844 2.604,1.844 2.844,1.844 false 0.438,0.313 0.75,0.469 0.313,0.156 10 false *1 2.896,1.74 3.208,1.896 0.313,0.156 10 false *2
*1 Generator Rotor Assembly
*2 Generator Drive End Frame


Remove the generator rotor assembly from the generator drive end frame.


Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A108429

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A264634N01
1.946,1.566 2.25,1.727 0.304,0.161 10 SST 1.912,1.647 1.213,1.354 false 1.912,1.647 1.204,1.136 false

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)