Home › Power Source / Network › 1KR-FE (BATTERY / CHARGING) › GENERATOR (for 100A Type) › from 2020.07
RM36W0E _57 Power Source / Network _090846 1KR-FE BATTERY / CHARGING _0432213 GENERATOR(for 100A Type) A

1KR-FE BATTERY / CHARGING  GENERATOR(for 100A Type)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A183132N04
1.073,0.677 0.531,0.281 0.531,0.281 0.948,1.042 false 2.354,0.677 1.865,0.323 1.865,0.323 2.156,0.833 false 0.219,0.198 0.583,0.365 0.365,0.167 10 SST 1.573,0.24 1.958,0.427 0.385,0.188 10 SST

Using SST and a press, install a new generator drive end frame bearing.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A153389C11
2.729,1.344 2.448,2 2.448,2 2.208,2 true 2.74,0.865 2.031,0.302 2.031,0.302 1.813,0.302 false 1.615,0.219 1.781,0.365 0.167,0.146 10 false *a 2.042,1.906 2.208,2.063 0.167,0.156 10 false *b
*a Tab
*b Cutout


Fit the tabs of the retainer plate into the cutouts of the generator drive end frame to install the retainer plate.


c.

Install the 4 screws.

Torque:
2.2 N*m (22 kgf*cm, 19 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

a.

Place the generator drive end frame on the generator pulley with clutch.


b.

Install the generator rotor assembly to the generator drive end frame.


Hide 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A314531C01
1.938,0.5 2.448,0.5 true 1.927,1.448 2.438,1.448 true 2.49,0.417 2.802,0.573 0.313,0.156 10 false *a 2.479,1.385 2.792,1.542 0.313,0.156 10 false *b
*a Protrusion
*b Groove


Install a new bearing cover packing.

NOTICE:

Align the protrusions of the bearing cover packing with the grooves of the generator coil assembly when installing.



b.
A285303N03
2.635,0.563 2.792,0.177 2.792,0.177 2.969,0.177 false 1.188,0.688 0.844,0.24 0.844,0.24 0.594,0.24 false 3.031,0.083 3.406,0.313 0.375,0.229 10 false SST 0.292,0.146 0.729,0.344 0.438,0.198 10 false SST

Using SST and a press, slowly press the generator coil assembly to install it.

SST
09612-70100  (09612-07240)


c.

Install the 4 bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A153827C12
2.479,0.74 1.979,0.198 1.979,0.198 1.729,0.198 false 0.917,0.521 0.708,0.198 0.708,0.198 0.458,0.198 false 1.521,0.094 1.833,0.313 0.313,0.219 10 false *a 0.271,0.104 0.583,0.323 0.313,0.219 10 false *a
*a Pin (1.0 mm)


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the generator brush holder assembly hole.


b.
A284142C02
1.76,1.042 2.646,1.656 2.646,1.656 2.854,1.656 false 2.917,1.604 3.229,1.76 0.313,0.156 10 false *a
*a Pin (1.0 mm)


Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.

Pull out the pin from the generator brush holder assembly hole.


Hide 5.INSTALL GENERATOR TERMINAL INSULATOR

a.

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the generator terminal insulator in the correct direction.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27415 7.INSTALL GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.

Temporarily install the generator pulley with clutch to the rotor shaft.


c.
A193558C02
1.25,0.281 1.479,0.281 1.479,0.281 1.896,0.708 false 2.885,1.802 2.885,1.094 false 2.594,2.823 2.594,2.49 false 1.063,0.167 1.375,0.323 0.313,0.156 10 false *a 2.677,1.854 3.177,2.115 0.5,0.26 10 false SST A 2.427,2.854 2.927,3.115 0.5,0.26 10 false SST A
*a Rotor Shaft


Place the rotor shaft end into SST (A).

SST
09820-63021  


d.
A193559C01
2.615,0.26 2.771,0.26 2.771,0.26 2.906,0.594 false 2.708,1.875 2.542,1.875 2.542,1.875 2.354,2.083 false 1.25,0.521 1.802,0.521 false 1.094,0.438 1.406,0.594 0.313,0.156 10 false *1 2.167,0.188 2.635,0.385 0.469,0.198 10 false SST B 2.781,1.792 3.25,1.99 0.469,0.198 10 false SST B
*1 Generator Pulley with Clutch


Fit SST (B) to the generator pulley with clutch.


e.
A325036C01
0.302,1.146 0.531,1.146 0.531,1.146 0.625,1.531 false 2.281,1.792 2.531,2.042 0.25,0.25 10 true *a 0.115,1.052 0.427,1.208 0.313,0.156 10 false *b 1.844,2.917 2.156,3.073 0.313,0.156 10 false *c 1.354,1.75 1.646,2.01 0.292,0.26 10 true *d
*a Hold
*b Turn
*c Length of SST 100 mm (3.94 in.)
*d Length of Torque Wrench 400 mm (1.312 ft.)


Tighten the generator pulley with clutch by turning SST (B) as shown in the illustration.

Torque:
Specified tightening torque : 80 N*m (816 kgf*cm, 59 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (1.312 ft.)): 64 N*m (653 kgf*cm, 47 ft.*lbf)




f.

Remove SST from the generator pulley with clutch.


g.

Check that the generator pulley with clutch rotates smoothly.


h.

Remove the generator assembly from the vise.


Hide 27416 8.INSTALL GENERATOR PULLEY CAP

a.

Install a new generator pulley cap to the generator pulley with clutch.