Clean the work area, tools to be used, other equipment, etc., thoroughly before performing this procedure, as there is a possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.
Do not use cotton work gloves, cloths, paper towels, etc., that may produce lint, dust or foreign matter.
When cleaning parts, make sure that dust or foreign matter does not enter the CVT.
When replacing any tapered roller bearing (inner race) or tapered roller bearing (outer race), replace both the tapered roller bearing (inner race) and tapered roller bearing (outer race) with new ones.
When the tapered roller bearing (inner race) is removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) need to be replaced.
When the tapered roller bearing (inner race) is not removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) can be reused.
Shift shock may increase after replacing the transmission valve body assembly or forward multiple disc clutch assembly. In this case, shift shock will reduce as the vehicle is driven.
33493C
1.REMOVE TRANSMISSION OIL COOLER ASSEMBLY
Remove the 3 bolts and transmission oil cooler from the transaxle housing.
Remove the 2 O-rings from the transaxle housing.
84540
2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
| *a | Piece of Wood or Equivalent |
Using a piece of wood or equivalent to secure the transmission control shaft lever to prevent it from rotating, remove the nut, washer and transmission control shaft lever from the manual valve lever shaft.
| *1 | Transmission Control Shaft Lever |
| *2 | Manual Valve Link Lever Sub-assembly |
| *3 | Manual Valve |
If the transmission control shaft lever is not secured when loosening the nut, the manual valve link lever sub-assembly may separate from the manual valve.
Remove the 2 bolts and park/neutral position switch assembly from the transaxle case sub-assembly.
89419B
3.REMOVE SHIFT STROKE SENSOR
Remove the bolt and shift stroke sensor from the transaxle case sub-assembly.
89413M
4.REMOVE TRANSMISSION REVOLUTION SENSOR (NOUT)
Remove the bolt and transmission revolution sensor (NOUT) from the transaxle case sub-assembly.
Remove the O-ring from the transmission revolution sensor (NOUT).
89413N
5.REMOVE TRANSMISSION REVOLUTION SENSOR (NT)
Remove the bolt and transmission revolution sensor (NT) from the rear transaxle case sub-assembly.
Remove the O-ring from the transmission revolution sensor (NT).
89413T
6.REMOVE TRANSMISSION REVOLUTION SENSOR (NSS)
Remove the bolt and transmission revolution sensor (NSS) from the transaxle case sub-assembly.
Remove the O-ring from the transmission revolution sensor (NSS).
35151K
7.REMOVE AUTOMATIC TRANSMISSION CASE COVER
Remove the 2 clips and automatic transmission case cover from the transaxle case sub-assembly.
89637K
8.REMOVE OIL PRESSURE SENSOR
Remove the oil pressure sensor from the rear transaxle case sub-assembly.
9.REMOVE REFILL PLUG
Remove the refill plug and gasket from the rear transaxle case sub-assembly.
30400
10.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
Place the continuously variable transaxle assembly on wooden blocks.
| *a | Wooden Block | - | - |
35125F
11.REMOVE OVERFLOW PLUG
Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle case sub-assembly.
35125E
12.REMOVE OVERFLOW(CVT) TUBE
Using a 6 mm hexagon socket wrench, remove the overflow (CVT) tube from the transaxle case sub-assembly.
35015Y
13.REMOVE TRANSAXLE SIDE COVER SUB-ASSEMBLY
Remove the 11 bolts and transaxle side cover sub-assembly from the transaxle case sub-assembly.
Remove the O-ring from the transaxle side cover sub-assembly.
35410J
14.REMOVE TRANSMISSION VALVE BODY ASSEMBLY
Temporarily install the transmission control shaft lever to the manual valve lever shaft.
Turn the transmission control shaft lever clockwise until it stops.
Remove the transmission control shaft lever from the manual valve lever shaft.
Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.
Disconnect the 6 solenoid valve connectors.
Remove the bolt and temperature sensor clamp from the transmission valve body assembly.
Disconnect the temperature sensor from the transmission valve body assembly.
Remove the 11 bolts and valve body assembly from the transaxle case sub-assembly.
Make sure the manual valve does not fall out when removing the transmission valve body assembly, as the manual valve is not secured to the transmission valve body assembly.
Remove the front oil pump cover gasket from the transaxle case sub-assembly.
w/ Stop and Start System:
Remove the 4 transaxle case gaskets from the transaxle case sub-assembly.
w/o Stop and Start System:
Remove the 3 transaxle case gaskets from the transaxle case sub-assembly.
82125M
15.REMOVE TRANSMISSION WIRE
Disconnect the transmission revolution sensor (NC1) connector.
Remove the bolt and transmission wire from the transaxle case sub-assembly.
Remove the O-ring from the temperature sensor.
89413S
16.REMOVE TRANSMISSION REVOLUTION SENSOR (NC1)
Remove the bolt and transmission revolution sensor (NC1) from the transaxle case sub-assembly.
35111C
17.REMOVE TRANSAXLE HOUSING
Remove the 20 bolts.
Using a plastic hammer, tap on the circumference of the transaxle housing to remove it from the transaxle case sub-assembly.
Remove the 5 O-rings from the transaxle case sub-assembly.
35174B
18.REMOVE OIL RESERVOIR LOCK PLATE
Remove the 3 bolts and oil reservoir lock plate from the transaxle housing.
35394D
19.REMOVE OIL CLEANER(CVT) MAGNET
Remove the 3 oil cleaner magnets from the oil reservoir lock plate.
35882E
20.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE
Remove the 2 bolts and differential gear lube apply tube from the transaxle housing.
35896A
21.REMOVE SECONDARY SHAFT LUBE APPLY TUBE
Using a snap ring plier, remove the snap ring from the transaxle housing.
Remove the secondary shaft lube apply tube from the transaxle housing.
Remove the O-ring from the secondary shaft lube apply tube.
35809
22.REMOVE C-2 CLUTCH PRESSURE APPLY TUBE SUB-ASSEMBLY
Remove the C-2 clutch pressure apply tube sub-assembly from the transaxle housing.
Remove the O-ring from the C-2 clutch pressure apply tube sub-assembly.
35593A
23.REMOVE CAM GUIDE SLEEVE
Remove the 2 bolts and cam guide sleeve from the transaxle housing.
35556N
24.REMOVE PARKING LOCK PAWL SHAFT
| *1 | Parking Lock Pawl Shaft |
| *2 | Torsion Spring |
Remove the parking lock pawl shaft and torsion spring from the transaxle housing.
35557C
25.REMOVE PARKING LOCK PAWL
Remove the parking lock pawl from the transaxle housing.
35598B
26.REMOVE PARKING LOCK SLEEVE
Remove the parking lock sleeve from the transaxle housing.
27.REMOVE REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the reduction driven gear front tapered roller bearing (outer race) and shim from the transaxle housing.
Be careful not to damage the transaxle housing.
Align the claw of SST with the indentation of the transaxle housing when removing the parts.
28.REMOVE DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the differential case front tapered roller bearing (outer race) and shim from the transaxle housing.
Be careful not to damage the transaxle housing.
Align the claw of SST with the indentation of the transaxle housing when removing the parts.
43410M
29.REMOVE FRONT DRIVE SHAFT OIL SEAL RH
Using SST and a hammer, remove the front drive shaft oil seal RH from the transaxle housing.
30.REMOVE CVT TYPE T OIL SEAL
Using SST and a hammer, remove the transaxle housing type T oil seal from the transaxle housing.
31.REMOVE REDUCTION DRIVEN GEAR SUB-ASSEMBLY
Remove the reduction driven gear sub-assembly from the transaxle case sub-assembly.
32.REMOVE DIFFERENTIAL CASE SUB-ASSEMBLY
Remove the differential case sub-assembly from the transaxle case sub-assembly.
35317A
33.REMOVE NO. 2 TRANSMISSION OIL PUMP SEPARATE PLATE
Disengage the 4 claws to remove the No. 2 transmission oil pump separate plate from the No. 1 transmission oil pump separate plate.
35782P
34.REMOVE DRIVE SPROCKET
Remove the thrust needle roller bearing from the drive sprocket.
| *1 | Drive Sprocket |
| *2 | Transmission Drive Chain |
Remove the drive sprocket and transmission drive chain.
35783M
35.REMOVE DRIVEN SPROCKET
Using a snap ring expander, remove the driven sprocket from the front oil pump assembly.
Remove the snap ring from the front oil pump assembly.
35316A
36.REMOVE NO. 1 TRANSMISSION OIL PUMP SEPARATE PLATE
Remove the 2 bolts and No. 1 transmission oil pump separate plate from the front oil pump assembly.
35310G
37.REMOVE FRONT OIL PUMP ASSEMBLY
Remove the 4 bolts and front oil pump assembly from the transaxle case sub-assembly.
Remove the front oil pump cover gasket from the transaxle case sub-assembly.
35330J
38.REMOVE OIL STRAINER ASSEMBLY
Remove the 2 bolts and oil strainer assembly from the front oil pump assembly.
Remove the O-ring from the oil strainer assembly.
35165B
39.REMOVE NO. 1 TRANSMISSION CASE PLATE
Remove the 2 bolts and No. 1 transmission case plate from the transaxle case sub-assembly.
35370E
40.REMOVE STATOR SHAFT ASSEMBLY
Remove the 7 bolts and stator shaft assembly from the transaxle case sub-assembly.
33032
41.REMOVE 1ST GEAR SUB-ASSEMBLY
Remove the bolt to disconnect the No. 1 gear shift fork assembly from the No. 1 gear shift fork shaft.
Remove the 1st gear sub-assembly with the No. 1 gear shift fork assembly from the No. 1 gear shift fork shaft.
33210A
42.REMOVE NO. 1 GEAR SHIFT FORK ASSEMBLY
Move the No. 1 gear shift fork assembly as shown in the illustration.
Remove the No. 1 gear shift fork assembly from the 1st gear sub-assembly.
43.REMOVE STAY
Remove the bolt and stay from the No. 1 gear shift fork assembly.
35610A
44.REMOVE FORWARD MULTIPLE DISC CLUTCH ASSEMBLY
Remove the forward multiple disc clutch assembly from the planetary gear assembly.
Remove the thrust bearing race from the forward multiple disc clutch assembly.
45.REMOVE NO. 1 CLUTCH DISC
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the forward clutch drum sub-assembly.
Be careful not to damage the forward clutch drum sub-assembly.
| *1 | Clutch Flange |
| *2 | No. 1 Clutch Disc |
| *3 | No. 1 Clutch Plate |
Remove the clutch flange, 3 No. 1 clutch discs and 3 No. 1 clutch plates from the forward clutch drum sub-assembly.
46.REMOVE NO. 1 CLUTCH BALANCER
Place SST on the No. 1 clutch balancer and compress the forward clutch return spring sub-assembly with a press.
Do not compress the forward clutch return spring sub-assembly excessively.
Using a snap ring expander, remove the snap ring from the forward clutch drum sub-assembly.
Remove the No. 1 clutch balancer from the forward clutch drum sub-assembly.
Remove the D-ring from the No. 1 clutch balancer.
35603E
47.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY
Remove the forward clutch return spring sub-assembly from the forward clutch drum sub-assembly.
48.REMOVE CLUTCH PISTON
Install the forward clutch drum sub-assembly to the stator shaft assembly.
Apply compressed air (approximately 250 kPa (2.5 kgf/cm2, 36 psi)) to the fluid hole of the stator shaft assembly to separate the clutch piston from the forward clutch drum sub-assembly.
Be careful as fluid may spray when applying compressed air.
Remove the clutch piston from the forward clutch drum sub-assembly.
| *1 | O-Ring |
| *2 | D-Ring |
Remove the O-ring and D-ring from the clutch piston.
Remove the forward clutch drum sub-assembly from the stator shaft assembly.
49.REMOVE CLUTCH DRUM OIL SEAL RING
Remove the 2 clutch drum oil seal rings from the stator shaft assembly.
Do not expand the clutch drum oil seal rings excessively.
35720M
50.REMOVE PLANETARY GEAR ASSEMBLY
Remove the planetary gear assembly from the front planetary ring gear sub-assembly.
Remove the thrust needle roller bearing from the planetary gear assembly.
35075D
51.REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY
Remove the thrust needle roller bearing from the front planetary ring gear sub-assembly.
Remove the front planetary ring gear sub-assembly from the transaxle case sub-assembly.
35726A
52.REMOVE PLANETARY RING GEAR THRUST WASHER
Remove the planetary ring gear thrust washer from the transaxle case sub-assembly.
35681B
53.REMOVE NO. 1 BRAKE DISC
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.
Be careful not to damage the transaxle case sub-assembly.
| *1 | Brake Flange |
| *2 | No. 1 Brake Disc |
| *3 | No. 1 Brake Plate |
| *4 | Brake Cushion Plate |
Remove the brake flange, 3 No. 1 brake discs, 3 No. 1 brake plates and brake cushion plate from the transaxle case sub-assembly.
54.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.
Do not compress the 1st and reverse brake return spring sub-assembly excessively.
Using a screwdriver with its tip wrapped with protective tape, remove the snap ring from the transaxle case sub-assembly.
Be careful not to damage the transaxle case sub-assembly.
Remove the 1st and reverse brake return spring sub-assembly from the transaxle case sub-assembly.
35623L
55.REMOVE REVERSE BRAKE PISTON
Apply compressed air (approximately 250 kPa (2.5 kgf/cm2, 36 psi)) to the fluid hole to disconnect the reverse brake piston from the transaxle case sub-assembly.
Be careful as fluid may spray when applying compressed air.
Remove the reverse brake piston from the transaxle case sub-assembly.
Remove the 2 O-rings from the reverse brake piston.
56.REMOVE REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the reduction driven gear rear tapered roller bearing (outer race) from the transaxle case sub-assembly.
Align the claw of SST with the indentation of the transaxle case sub-assembly when removing the parts.
57.REMOVE DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)
Using SST, remove the differential case rear tapered roller bearing (outer race) from the transaxle case sub-assembly.
Align the claw of SST with the indentation of the transaxle case sub-assembly when removing the parts.
43420H
58.REMOVE FRONT DRIVE SHAFT OIL SEAL LH
Using SST and a hammer, remove the front drive shaft oil seal LH from the transaxle case sub-assembly.
59.REMOVE REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold |
| *b | Turn |
Using SST, remove the reduction driven gear rear tapered roller bearing (inner race) from the reduction driven gear sub-assembly.
Because SST is attached to the roller portion, there is a possibility that the roller portion could break and SST could come off before the reduction driven gear rear tapered roller bearing (inner race) comes off.
| *a | Hold |
| *b | Turn |
If the roller portion breaks and SST comes off, reattach SST to the inner race in the position shown in the illustration, and continue removing the parts.
60.REMOVE REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold |
| *b | Turn |
Using SST, remove the reduction driven gear front tapered roller bearing (inner race) from the reduction driven gear sub-assembly.
61.REMOVE DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold |
| *b | Turn |
Using SST, remove the differential case rear tapered roller bearing (inner race) from the differential case sub-assembly.
62.REMOVE DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)
| *a | Hold |
| *b | Turn |
Using SST, remove the differential case front tapered roller bearing (inner race) from the differential case sub-assembly.
63.REMOVE STRAIGHT PIN
Remove the 2 straight pins from the transaxle case sub-assembly.