Home › Drivetrain › K320 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE UNIT › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422056 CONTINUOUSLY VARIABLE TRANSAXLE UNIT A

K320 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Clean the work area, tools to be used, other equipment, etc., thoroughly before performing this procedure, as there is a possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, paper towels, etc., that may produce lint, dust or foreign matter.

·

When cleaning parts, make sure that dust or foreign matter does not enter the CVT.

·

When replacing any tapered roller bearing (inner race) or tapered roller bearing (outer race), replace both the tapered roller bearing (inner race) and tapered roller bearing (outer race) with new ones.

·

When the tapered roller bearing (inner race) is removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) need to be replaced.

·

When the tapered roller bearing (inner race) is not removed, the tapered roller bearing (inner race) and tapered roller bearing (outer race) can be reused.



HINT:

Shift shock may increase after replacing the transmission valve body assembly or forward multiple disc clutch assembly. In this case, shift shock will reduce as the vehicle is driven.


PROCEDURE

Hide 1. BEARING POSITION

a.

Check the position and installation direction of each bearing.

C432758N01
2.75,3.354 2.948,3.604 0.198,0.25 10 false A 2.188,7.51 2.385,7.76 0.198,0.25 10 false B 3.604,6.729 3.802,6.979 0.198,0.25 10 false C

Thrust Needle Roller Bearing and Thrust Bearing Race Diameter
Mark Thrust Bearing Race Diameter Inside / Outside
mm (in.)
Thrust Needle Roller Bearing Diameter Inside / Outside
mm (in.)
A - 47.75 (1.88) / 65.8 (2.59)
B 26.38 (1.04) / 38.9 (1.53) 24.9 (0.98) / 38.9 (1.53)
C - 29.7 (1.17) / 49.1 (1.93)


Hide 2.INSTALL STRAIGHT PIN

a.
C432759

Install the 2 straight pins to the transaxle case sub-assembly.

Protrusion Height:

7.0 to 8.0 mm (0.276 to 0.315 in.)



Hide 3.INSTALL DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C432760N01
1.083,2 1.417,2 false 0.75,1.917 1.042,2.135 0.292,0.219 10 true SST

Using SST and a press, install a new differential case rear tapered roller bearing (inner race) to the differential case sub-assembly.

SST
09223-00010  

NOTICE:
·

Do not damage the differential case rear tapered roller bearing (inner race) cage when installing the differential case rear tapered roller bearing (inner race).

·

Be sure to install the differential case rear tapered roller bearing (inner race) so that there is no clearance between the differential case rear tapered roller bearing (inner race) and the differential case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.




Hide 4.INSTALL DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C432761N01
0.958,2.104 1.448,1.938 false 0.604,2.042 0.948,2.229 0.344,0.188 10 true SST

Using SST and a press, install a new differential case front tapered roller bearing (inner race) to the differential case sub-assembly.

SST
09309-37010  

NOTICE:
·

Do not damage the differential case front tapered roller bearing (inner race) cage when installing the differential case front tapered roller bearing (inner race).

·

Be sure to install the differential case front tapered roller bearing (inner race) so that there is no clearance between the differential case front tapered roller bearing (inner race) and the differential case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.




Hide 5.INSTALL DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C432762N01
0.938,1.531 0.417,1.094 0.417,1.094 1.01,1.323 true 0.104,0.979 0.469,1.198 0.365,0.219 10 false SST

Using SST and a hammer, install a new differential case rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60021  (09951-00680)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the differential case rear tapered roller bearing (outer race) so that there is no clearance between the differential case rear tapered roller bearing (outer race) and the transaxle case sub-assembly. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.



Hide 6.INSTALL DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C432763

Install the shim to the transaxle housing.


b.
C432764N01
0.865,1.479 0.396,1.594 0.396,1.594 1.01,1.156 true 0.083,1.521 0.406,1.76 0.323,0.24 10 true SST

Using SST and a hammer, install a new differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60011  (09951-00650)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the differential case front tapered roller bearing (outer race) so that there is no clearance between the differential case front tapered roller bearing (outer race), shim and the transaxle housing. If there is any clearance, the turning torque of the differential case sub-assembly cannot be measured correctly.



Hide 7.ADJUST DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case sub-assembly.

NOTICE:

Make sure that there is no Toyota Genuine CVT fluid FE on the contact surfaces.



b.
C432765

Install the differential case sub-assembly to the transaxle case sub-assembly.


c.
C432696

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


d.
C432766N01
0.521,1.51 1.667,1.51 true 0.198,1.417 0.573,1.646 0.375,0.229 10 false SST

Using SST, turn the differential case sub-assembly right and left 2 or 3 times to settle the bearings.

SST
09564-32011  


e.
C432767N01
0.531,1.531 1.667,1.521 true 0.208,1.427 0.583,1.646 0.375,0.219 10 false SST

Using SST and a torque wrench, measure the turning torque of the differential case tapered roller bearing while rotating SST at 10 rpm.

SST
09564-32011  

Standard Turning Torque:

1.61 to 2.57 N*m (17 to 26 kgf*cm, 15 to 22 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness:
Part Number Thickness
mm (in.)
90564-58002 1.76 (0.0693)
90564-58003 1.79 (0.0705)
90564-58004 1.82 (0.0717)
90564-58005 1.85 (0.0728)
90564-58006 1.88 (0.0740)
90564-58007 1.91 (0.0752)
90564-58008 1.94 (0.0764)
90564-58009 1.97 (0.0776)
90564-58010 2.00 (0.0787)
90564-58011 2.03 (0.0799)
90564-58012 2.06 (0.0811)
90564-58013 2.09 (0.0823)
90564-58014 2.12 (0.0835)
90564-58015 2.15 (0.0846)
90564-58016 2.18 (0.0858)
90564-58017 2.21 (0.0870)
90564-58018 2.24 (0.0882)
90564-58019 2.27 (0.0894)
90564-58020 2.30 (0.0906)
90564-58021 2.33 (0.0917)



f.

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


g.

Remove the differential case sub-assembly from the transaxle case sub-assembly.


Hide 8.INSTALL REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (INNER RACE)

a.
C432768N01
1.198,1.969 1.542,1.969 false 0.885,1.896 1.25,2.115 0.365,0.219 10 false SST

Using SST and a press, install a new reduction driven gear rear tapered roller bearing (inner race) to the reduction driven gear sub-assembly.

SST
09325-40010  

NOTICE:
·

Do not damage the reduction driven gear rear tapered roller bearing (inner race) cage when installing the reduction driven gear rear tapered roller bearing (inner race).

·

Be sure to install the reduction driven gear rear tapered roller bearing (inner race) so that there is no clearance between the reduction driven gear rear tapered roller bearing (inner race) and the reduction driven gear sub-assembly. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.




Hide 9.INSTALL REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (INNER RACE)

a.
C432769N01
1.479,2.458 1.073,1.74 1.073,1.74 1.5,2.104 false 1.656,3.146 2.438,3.188 true 0.802,1.656 1.156,1.865 0.354,0.208 10 false SST 2.469,3.104 2.823,3.313 0.354,0.208 10 false SST

Using SST and a press, install a new reduction driven gear front tapered roller bearing (inner race) to the reduction driven gear sub-assembly.

SST
09950-60011  (09951-00300, 09951-00320)
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the reduction driven gear front tapered roller bearing (inner race) cage when installing the reduction driven gear front tapered roller bearing (inner race).

·

Be sure to install the reduction driven gear front tapered roller bearing (inner race) so that there is no clearance between the reduction driven gear front tapered roller bearing (inner race) and the reduction driven gear sub-assembly. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.




Hide 10.INSTALL REDUCTION DRIVEN GEAR REAR TAPERED ROLLER BEARING (OUTER RACE)

a.
C432770N01
1.063,1.625 0.469,1.229 0.469,1.229 1.135,1.448 true 0.125,1.135 0.479,1.344 0.354,0.208 10 false SST

Using SST and a hammer, install a new reduction driven gear rear tapered roller bearing (outer race) to the transaxle case sub-assembly.

SST
09950-60011  (09951-00560)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the reduction driven gear rear tapered roller bearing (outer race) so that there is no clearance between the reduction driven gear rear tapered roller bearing (outer race) and the transaxle case sub-assembly. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.



Hide 11.INSTALL REDUCTION DRIVEN GEAR FRONT TAPERED ROLLER BEARING (OUTER RACE)

a.
C432771

Install the shim to the transaxle housing.


b.
C432772N01
1.323,1.531 0.615,0.698 0.615,0.698 1.406,1.281 true 0.313,0.625 0.771,0.823 0.458,0.198 10 false SST

Using SST and a hammer, install a new reduction driven gear front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60011  (09951-00500)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the reduction driven gear front tapered roller bearing (outer race) so that there is no clearance between the reduction driven gear front tapered roller bearing (outer race), shim and the transaxle housing. If there is any clearance, the turning torque of the reduction driven gear sub-assembly cannot be measured correctly.



Hide 12.ADJUST REDUCTION DRIVEN GEAR TAPERED ROLLER BEARING PRELOAD

a.
C432773

Turn the reduction drive gear assembly right and left 2 or 3 times to settle the bearings.


b.

Install SST.

i.

Set SST to the parking lock gear as shown in the illustration.

C432774C01
3.979,2.042 5.927,1.135 5.927,1.135 4.542,1.135 true 4,0.5 4.354,0.5 false 6.01,1.052 6.469,1.25 0.458,0.198 10 false SST 4.396,0.396 4.708,0.667 0.313,0.271 10 false *a
*a SST (Center Bolt) - -


SST
09950-40011  (09951-04010, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
09950-60011  (09951-00360, 09951-00250, 09952-06010)

NOTICE:

Do not tighten SST (center bolt) more than is necessary to hold SST in place or the parking lock gear or bearing may unseat.



ii.
C432775C01
1.188,0.375 1.531,0.375 false 1,0.271 1.281,0.5 0.281,0.229 10 false *a
*a SST (Center Bolt)


Tighten SST (center bolt).

HINT:

Torque: 0.5 N*m (5 kgf*cm, 4 in.*lbf)




c.
C432776

Using a torque wrench, measure and note the turning torque (T1) of the reduction drive gear assembly while rotating SST at 10 rpm.

HINT:

No specified range is provided for T1 as it is only used for calculating the total preload of the differential case sub-assembly and reduction driven gear sub-assembly.



d.

Remove SST from the parking lock gear.


e.
C432716

Install the differential case sub-assembly to the transaxle case sub-assembly.


f.
C432777

Install the reduction driven gear sub-assembly to the transaxle case sub-assembly.


g.
C432696

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


h.
C434369N01
0.531,1.531 1.667,1.521 true 0.208,1.427 0.583,1.646 0.375,0.219 10 false SST

Using SST, turn the differential case sub-assembly right and left 2 or 3 times to settle the bearings.

SST
09564-32011  


i.
C432767N01
0.531,1.531 1.667,1.521 true 0.208,1.427 0.583,1.646 0.375,0.219 10 false SST

Using a torque wrench, measure and note the turning torque (T2) of the differential case tapered roller bearing while rotating SST at 10 rpm.

SST
09564-32011  


j.

Subtract T1 from T2 to calculate the total preload of the differential case sub-assembly and reduction driven gear sub-assembly.

Standard Turning Torque:

Differential case tapered roller bearing preload + 2.63 to 4.88 N*m (27 to 49 kgf*cm, 2 to 3 ft.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness:
Part Number Thickness
mm (in.)
Mark
90564-44074 1.71 (0.0673) E
90564-44075 1.74 (0.0685) F
90564-44076 1.77 (0.0697) G
90564-44077 1.80 (0.0709) H
90564-44078 1.83 (0.0720) J
90564-44079 1.86 (0.0732) K
90564-44080 1.89 (0.0744) L
90564-44081 1.92 (0.0756) M
90564-44082 1.95 (0.0768) N
90564-44083 1.98 (0.0780) P
90564-44084 2.01 (0.0791) Q
90564-44085 2.04 (0.0803) R
90564-44086 2.07 (0.0815) S
90564-44087 2.10 (0.0827) T
90564-44088 2.13 (0.0839) U
90564-44089 2.16 (0.0850) V
90564-44090 2.19 (0.0862) W
90564-44091 2.22 (0.0874) X
90564-44092 2.25 (0.0886) Y
90564-44093 2.28 (0.0898) -
90564-44094 2.31 (0.0909) -
90564-44095 2.34 (0.0921) -
90564-44096 2.37 (0.0933) -



k.

Remove the 20 bolts and transaxle housing from the transaxle case sub-assembly.


l.

Remove the reduction driven gear sub-assembly from the transaxle case sub-assembly.


m.

Remove the differential case sub-assembly from the transaxle case sub-assembly.


Hide 43420H 13.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C432778N01
2.188,2.302 2.688,2.792 true 2.719,2.76 3.094,2.979 0.375,0.219 10 false SST

Using SST and a hammer, install a new front drive shaft oil seal LH to the transaxle case sub-assembly.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal LH is installed in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 35623L 14.INSTALL REVERSE BRAKE PISTON

a.
C395759

Coat 2 new O-rings with Toyota Genuine CVT fluid FE and install them to the reverse brake piston.

NOTICE:

Ensure that the O-rings is not twisted.



b.
C432746

Install the reverse brake piston to the transaxle case sub-assembly.


Hide 15.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C432744

Install the 1st and reverse brake return spring sub-assembly to the transaxle case sub-assembly.


b.
C432742N01
1.771,1.198 2.385,0.833 true 2.417,0.74 2.74,0.927 0.323,0.188 10 true SST

Place SST on the 1st and reverse brake return spring sub-assembly and compress it with a press.

SST
09223-56010  

NOTICE:

Do not compress the 1st and reverse brake return spring sub-assembly excessively.



c.
C432743

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the transaxle case sub-assembly.

NOTICE:

Be careful not to damage the transaxle case sub-assembly.



Hide 35681B 16.INSTALL NO. 1 BRAKE DISC

a.
C432741C01
3.135,1.167 3.302,1.167 3.302,1.167 3.302,2.729 false 3.135,1.635 3.302,1.635 false 3.135,2.115 3.302,2.115 false 2.073,0.917 2.073,1.917 2.073,1.917 2.25,1.917 false 2.25,0.917 1.906,0.917 false 2.25,1.417 2.073,1.417 false 1.938,0.583 2.271,0.583 false 2.24,2.406 2.052,2.406 false 1.74,0.5 1.917,0.708 0.177,0.208 10 true *1 1.74,0.813 1.906,1.031 0.167,0.219 10 true *2 3.208,2.729 3.396,2.969 0.188,0.24 10 false *3 1.875,2.323 2.094,2.594 0.219,0.271 10 false *4
*1 Brake Flange
*2 No. 1 Brake Disc
*3 No. 1 Brake Plate
*4 Brake Cushion Plate


Install the brake flange, 3 No. 1 brake discs, 3 No. 1 brake plates and brake cushion plate to the transaxle case sub-assembly.


b.

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the transaxle case sub-assembly.

C432779C01
5.146,0.073 5.417,0.302 0.271,0.229 10 false *a
*a Snap ring opening within this area. - -


NOTICE:

Be careful not to damage the transaxle case sub-assembly.



Hide 35726A 17.INSTALL PLANETARY RING GEAR THRUST WASHER

a.
C432739

Install the planetary ring gear thrust washer to the transaxle case sub-assembly.


Hide 35075D 18.INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY

a.
C432738

Install the front planetary ring gear sub-assembly to the transaxle case sub-assembly.


b.
C432780

Coat the thrust needle roller bearing with Toyota Genuine CVT fluid FE and install it to the front planetary ring gear sub-assembly.


Hide 35720M 19.INSTALL PLANETARY GEAR ASSEMBLY

a.
C432781

Coat the thrust needle roller bearing with Toyota Genuine CVT fluid FE and install it to the planetary gear assembly.


b.
C432735

Install the planetary gear assembly to the front planetary ring gear sub-assembly.


Hide 20.INSTALL CLUTCH PISTON

a.
C395740C01
1.021,0.302 1.302,0.49 0.281,0.188 10 false *1 2.625,1.844 2.896,2.042 0.271,0.198 10 false *2
*1 O-Ring
*2 D-Ring


Coat a new O-ring and a new D-ring with Toyota Genuine CVT fluid FE and install them to the clutch piston.

NOTICE:

Ensure that the O-ring and D-ring are not twisted.



b.
C395739

Install the clutch piston to the forward clutch drum sub-assembly.


Hide 35603E 21.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C395736

Install the forward clutch return spring sub-assembly to the forward clutch drum sub-assembly.


Hide 22.INSTALL NO. 1 CLUTCH BALANCER

a.
C395735

Coat a new D-ring with Toyota Genuine CVT fluid FE and install it to the No. 1 clutch balancer.

NOTICE:

Ensure that the D-ring is not twisted.



b.
C395734

Install the No. 1 clutch balancer to the forward clutch drum sub-assembly.


c.
C395732N01
1.906,0.917 2.396,0.917 false 2.448,0.823 2.833,1.094 0.385,0.271 10 false SST

Place SST on the No. 1 clutch balancer and compress the forward clutch return spring sub-assembly with a press.

SST
09387-00020  

NOTICE:

Do not compress the forward clutch return spring sub-assembly excessively.



d.
C395733

Using a snap ring expander, install the snap ring to the forward clutch drum sub-assembly.


Hide 23.INSTALL NO. 1 CLUTCH DISC

a.
C395731C01
3.146,1.292 3.292,1.292 3.292,1.292 3.292,2.792 false 2.021,2.156 1.833,2.156 1.833,2.156 1.833,1.021 false 1.625,1.021 2.031,1.021 false 1.833,1.583 2.021,1.583 false 3.167,1.885 3.292,1.885 false 3.156,2.49 3.292,2.49 false 1.625,0.698 2.031,0.698 false 1.469,0.604 1.771,0.823 0.302,0.219 10 false *1 1.469,0.927 1.76,1.156 0.292,0.229 10 false *2 3.229,2.792 3.417,3.01 0.188,0.219 10 false *3
*1 Clutch Flange
*2 No. 1 Clutch Disc
*3 No. 1 Clutch Plate


Install the clutch flange, 3 No. 1 clutch discs and 3 No. 1 clutch plates to the forward clutch drum sub-assembly.


b.
C432734

Using a screwdriver with its tip wrapped with protective tape, install the snap ring to the forward clutch drum sub-assembly.

NOTICE:

Be careful not to damage the forward clutch drum sub-assembly.



Hide 35610A 24.INSTALL FORWARD MULTIPLE DISC CLUTCH ASSEMBLY

a.
C432782

Install the thrust bearing race to the forward multiple disc clutch assembly.


b.
C432733

Install the forward multiple disc clutch assembly to the planetary gear assembly.


Hide 25.INSTALL STAY

a.

Clean and degrease the bolt and installation hole in the No. 1 gear shift fork assembly.


b.
P000601C22
1.979,1.177 2.177,0.229 2.177,0.229 2.302,0.229 false 2.323,0.135 2.521,0.323 0.198,0.188 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.



c.
C432732

Install the stay to the No. 1 gear shift fork assembly with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 33210A 26.INSTALL NO. 1 GEAR SHIFT FORK ASSEMBLY

a.
C432731

Install the No. 1 gear shift fork assembly to the 1st gear sub-assembly.


b.

Move the No. 1 gear shift fork assembly as shown in the illustration.

C432783


Hide 33032 27.INSTALL 1ST GEAR SUB-ASSEMBLY

a.

Clean and degrease the bolt and installation hole in the No. 1 gear shift fork shaft.


b.
C432729

Install the 1st gear sub-assembly with the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft.


c.
C395724C01
1.969,1.219 2.094,0.406 2.094,0.406 2.26,0.406 false 2.302,0.292 2.594,0.552 0.292,0.26 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

In order to ensure proper sealing of the bolt, apply adhesive to the bolt and install it within 10 minutes of adhesive application.



d.
C432728

Install the bolt to connect the No. 1 gear shift fork assembly to the No. 1 gear shift fork shaft.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 28.INSTALL CLUTCH DRUM OIL SEAL RING

a.
C395741

Install 2 new clutch drum oil seal rings to the stator shaft assembly.

NOTICE:

Do not expand the gap of the clutch drum oil seal ring excessively.



Hide 35370E 29.INSTALL STATOR SHAFT ASSEMBLY

a.
C432727N01
0.573,0.063 0.74,0.208 0.167,0.146 10 true A 3.073,1.229 3.229,1.427 0.156,0.198 10 true B 2.74,0.313 2.896,0.51 0.156,0.198 10 true A 0.313,0.604 0.438,0.802 0.125,0.198 10 true B 0.406,1.01 0.531,1.208 0.125,0.198 10 true A 0.521,1.5 0.635,1.708 0.115,0.208 10 true A 2.969,0.75 3.125,0.948 0.156,0.198 10 true A

Install the stator shaft assembly to the transaxle case sub-assembly with the 7 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
30 mm (1.18 in.) 40 mm (1.57 in.)



Hide 35165B 30.INSTALL NO. 1 TRANSMISSION CASE PLATE

a.
C432726

Install the No. 1 transmission case plate to the transaxle case sub-assembly with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35330J 31.INSTALL OIL STRAINER ASSEMBLY

a.
C432725

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted.



b.
C432724

Install the oil strainer assembly to the front oil pump assembly with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35310G 32.INSTALL FRONT OIL PUMP ASSEMBLY

a.
C432723

Coat a new front oil pump cover gasket with Toyota Genuine CVT fluid FE and install it to the transaxle case sub-assembly.


b.
C432722N01
1.188,0.021 1.323,0.167 0.135,0.146 10 true A 1.323,1.771 1.479,1.958 0.156,0.188 10 true B 2.5,1.479 2.656,1.677 0.156,0.198 10 true A 2.76,0.792 2.917,0.979 0.156,0.188 10 true B

Install the front oil pump assembly to the transaxle case sub-assembly with the 4 bolts.

Torque:
22.1 N*m (225 kgf*cm, 16 ft.*lbf)

Bolt Length:
Bolt (A) Bolt (B)
30 mm (1.18 in.) 40 mm (1.57 in.)



Hide 35316A 33.INSTALL NO. 1 TRANSMISSION OIL PUMP SEPARATE PLATE

a.
C432721

Install the No. 1 transmission oil pump separate plate to the front oil pump assembly with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35783M 34.INSTALL DRIVEN SPROCKET

a.

Install the snap ring to the front oil pump assembly.

C432720


b.

Using a snap ring expander, install the driven sprocket to the front oil pump assembly.


Hide 35782P 35.INSTALL DRIVE SPROCKET

a.
C432719C01
1.198,0.292 1.792,0.292 true 2.177,0.469 2.656,0.469 true 1.01,0.208 1.292,0.448 0.281,0.24 10 false *1 2.708,0.354 2.99,0.594 0.281,0.24 10 false *2
*1 Drive Sprocket
*2 Transmission Drive Chain


Install the drive sprocket and transmission drive chain.


b.
C432784

Install the thrust needle roller bearing to the drive sprocket.


Hide 35317A 36.INSTALL NO. 2 TRANSMISSION OIL PUMP SEPARATE PLATE

a.
C432717

Engage the 4 claws to install the No. 2 transmission oil pump separate plate to the No. 1 transmission oil pump separate plate.


Hide 37.INSTALL DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C432716

Install the differential case sub-assembly to the transaxle case sub-assembly.


Hide 38.INSTALL REDUCTION DRIVEN GEAR SUB-ASSEMBLY

a.
C432715

Install the reduction driven gear sub-assembly to the transaxle case sub-assembly.


Hide 39.INSTALL CVT TYPE T OIL SEAL

a.

Coat the lip of a new transaxle housing type T oil seal with a small amount of MP grease.


b.
C432785N01
0.531,1.229 0.781,1.229 true 0.208,1.135 0.5,1.313 0.292,0.177 10 true SST

Using SST and a hammer, install the transaxle housing type T oil seal to the transaxle housing.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Make sure that the transaxle housing type T oil seal is installed in the correct direction.



Hide 43410M 40.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C432786N01
0.563,1.229 0.938,1.396 false 0.25,1.146 0.563,1.323 0.313,0.177 10 true SST

Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Make sure that the front drive shaft oil seal RH is installed in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 35598B 41.INSTALL PARKING LOCK SLEEVE

a.
C432708

Install the parking lock sleeve to the transaxle housing.


Hide 35557C 42.INSTALL PARKING LOCK PAWL

a.
C432707

Install the parking lock pawl to the transaxle housing.


Hide 35556N 43.INSTALL PARKING LOCK PAWL SHAFT

a.
C432787C01
1.021,0.198 1.521,0.198 false 1.125,0.688 1.333,0.5 1.333,0.5 1.521,0.5 false 1.563,0.094 1.844,0.313 0.281,0.219 10 false *1 1.563,0.396 1.885,0.615 0.323,0.219 10 false *2
*1 Parking Lock Pawl Shaft
*2 Torsion Spring


Install the parking lock pawl shaft and torsion spring to the transaxle housing.


Hide 35593A 44.INSTALL CAM GUIDE SLEEVE

a.
C432705

Install the cam guide sleeve to the transaxle housing with the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35809 45.INSTALL C-2 CLUTCH PRESSURE APPLY TUBE SUB-ASSEMBLY

a.
C395537

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the C-2 clutch pressure apply tube sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



b.
C432703

Install the C-2 clutch pressure apply tube sub-assembly to the transaxle housing.


Hide 35896A 46.INSTALL SECONDARY SHAFT LUBE APPLY TUBE

a.
C395535

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the secondary shaft lube apply tube.

NOTICE:

Ensure that the O-ring is not twisted.



b.

Install the secondary shaft lube apply tube to the transaxle housing.

C432788C01
3.698,0.813 4.094,1.042 true 5.323,1.365 5.583,1 true 4.167,0.958 4.448,1.219 0.281,0.26 10 false *a 5.229,1.365 5.458,1.542 0.229,0.177 10 false *b
*a Protrusion *b Cutout


NOTICE:

Align the cutout of the transaxle housing with the protrusion of the secondary shaft lube apply tube.



c.
C432701

Using a snap ring plier, install the snap ring to the transaxle housing.


Hide 35882E 47.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C432700

Install the differential gear lube apply tube to the transaxle housing with the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35394D 48.INSTALL OIL CLEANER(CVT) MAGNET

a.
C432699

Install the 3 oil cleaner magnets to the oil reservoir lock plate.


Hide 35174B 49.INSTALL OIL RESERVOIR LOCK PLATE

a.
C432698

Install the oil reservoir lock plate to the transaxle housing with the 3 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35111C 50.INSTALL TRANSAXLE HOUSING

a.

Clean and degrease the contact surfaces of the transaxle housing and transaxle case sub-assembly.

NOTICE:

Make sure that there is no Toyota Genuine CVT fluid FE on the contact surfaces.



b.

Clean and degrease the 20 bolts and installation holes of the transaxle case sub-assembly.


c.
C432697

Coat 5 new O-rings with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.

NOTICE:

Ensure that the O-rings is not twisted.



d.
C432789C01
0,0 0,0 false
V100155

Seal Packing Start and End Point Range


Apply seal packing to the transaxle case sub-assembly.

Seal Packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Standard Seal Diameter:

1.5 mm (0.0591 in.)


NOTICE:
·

Make sure to overlap the start and end points of the seal packing.

·

Make sure that the start and end points of the seal packing are within the shaded area shown in the illustration.

·

Apply seal packing in a continuous line (width 1.5 mm (0.0591 in.)) along the sealing surface.

·

After applying seal packing, install the transaxle housing to the transaxle case sub-assembly within 3 minutes and tighten the bolts within 10 minutes.




e.
C432696

Install the transaxle housing to the transaxle case sub-assembly with the 20 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 89413S 51.INSTALL TRANSMISSION REVOLUTION SENSOR (NC1)

a.
C432695

Install the transmission revolution sensor (NC1) to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 82125M 52.INSTALL TRANSMISSION WIRE

a.
C429258

Coat the O-ring of the transmission wire with Toyota Genuine CVT fluid FE.

NOTICE:

If reusing the transmission wire, check that the O-ring is not damaged.



b.
C395524

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the temperature sensor.

NOTICE:

Ensure that the O-ring is not twisted.



c.
C432694

Install the transmission wire to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.
C432693

Connect the transmission revolution sensor (NC1) connector.

NOTICE:
C467180

Securely align the wire harness with the cutout of the transaxle case sub-assembly.



Hide 35410J 53.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C467183

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


b.

Turn the transmission control shaft lever clockwise until it stops.


c.

Remove the transmission control shaft lever from the manual valve lever shaft.


d.

w/ Stop and Start System:

i.
C439380

Coat 4 new transaxle case gaskets with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.



e.

w/o Stop and Start System:

i.
C432692

Coat 3 new transaxle case gaskets with Toyota Genuine CVT fluid FE and install them to the transaxle case sub-assembly.



f.
C432691

Coat a new front oil pump cover gasket with Toyota Genuine CVT fluid FE and install it to the transaxle case sub-assembly.


g.

Align the slit portion of the manual valve and the manual valve link lever sub-assembly as shown in the illustration, and temporarily install the transmission valve body assembly to the transaxle case sub-assembly with the 2 bolts.

C432790C01
6.219,1.708 6.375,1.469 true 5.833,0.99 5.656,0.781 false 5.49,0.688 5.75,0.917 0.26,0.229 10 false *1 6.042,1.625 6.313,1.823 0.271,0.198 10 false *2
*1 Manual Valve *2 Manual Valve Link Lever Sub-assembly


Bolt Length:

40 mm (1.57 in.)



h.
C432791N01
1.156,1.938 1.313,2.135 0.156,0.198 10 true A 1.51,1.927 1.667,2.125 0.156,0.198 10 true A 1.813,1.969 1.969,2.167 0.156,0.198 10 true A 2.01,0.115 2.167,0.313 0.156,0.198 10 true A 1.417,0.094 1.573,0.292 0.156,0.198 10 true B 0.052,0.792 0.208,0.99 0.156,0.198 10 true B 0.76,1.167 0.917,1.365 0.156,0.198 10 true B 0.615,0.063 0.771,0.26 0.156,0.198 10 true B 2.979,1.313 3.135,1.51 0.156,0.198 10 true B

Temporarily install the 9 bolts.

Bolt Length:
Bolt (A) Bolt (B)
40 mm (1.57 in.) 55 mm (2.17 in.)



i.
C432792

Connect the temperature sensor to the transmission valve body assembly.

NOTICE:

To prevent it from being pinched between the transmission valve body assembly and the transaxle side cover sub-assembly, do not let the transmission wire ride up over the area shown in the illustration.

C432793C01
0,0 0,0 false
V100145

Do not let transmission wire protrude into this area. - -




j.
C432689

Temporarily install the temperature sensor clamp to the transmission valve body assembly with the bolt.

Bolt Length:

55 mm (2.17 in.)



k.
C434367

Fully tighten the 12 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


l.
C432688

Connect the 6 solenoid valve connectors.


m.

Engage the clamp to connect the transmission wire to the solenoid lock plate.


Hide 35015Y 54.INSTALL TRANSAXLE SIDE COVER SUB-ASSEMBLY

a.
C432795C01
0,0 0,0 false
V100145

Area to be cleaned


Clean the transaxle side cover sub-assembly installation surface of the transaxle case sub-assembly.

NOTICE:

Completely remove any oil or grease from the contact surface of the transaxle case sub-assembly.



b.
C395511

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transaxle side cover sub-assembly.

NOTICE:

Ensure that the O-ring is not twisted.



c.
C432687N01
0.427,0.219 0.583,0.417 0.156,0.198 10 false 8 2.615,1.906 2.771,2.104 0.156,0.198 10 false 4 2.833,0.49 2.99,0.688 0.156,0.198 10 false 2 0.427,1.896 0.583,2.094 0.156,0.198 10 false 1 0.292,1.042 0.521,1.271 0.229,0.229 10 false 7 2.865,1.104 3.021,1.302 0.156,0.198 10 false 3 1.49,0.115 1.646,0.313 0.156,0.198 10 true 9 2.021,1.948 2.177,2.146 0.156,0.198 10 true 5 1.906,0.052 2.146,0.229 0.24,0.177 10 true 10 2.094,0.323 2.302,0.521 0.208,0.198 10 true 11 1.25,1.979 1.406,2.177 0.156,0.198 10 false 6

Temporarily install a new transaxle side cover sub-assembly to the transaxle case sub-assembly with the 11 bolts.


d.

Fully tighten the 11 bolts in the order shown in the illustration.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35125E 55.INSTALL OVERFLOW (CVT) TUBE

a.
C432686

Using a 6 mm hexagon socket wrench, install the overflow (CVT) tube to the transaxle case sub-assembly.

Torque:
0.8 N*m (8 kgf*cm, 7 in.*lbf)


Hide 35125G 56.INSTALL OVERFLOW PLUG

a.

Coat a new gasket with Toyota Genuine CVT fluid FE and install it to the overflow plug.


b.
C432685

Using a 10 mm hexagon socket wrench, install the overflow plug to the transaxle case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 57.INSTALL REFILL PLUG

a.

Coat a new gasket with Toyota Genuine CVT fluid FE and install it to the refill plug .


b.
C432683

Install the refill plug to the rear transaxle case sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 89637K 58.INSTALL OIL PRESSURE SENSOR

a.
C395505

Coat the O-ring of the oil pressure sensor with Toyota Genuine CVT fluid FE.

NOTICE:

If reusing the oil pressure sensor, check that the O-ring is not damaged.



b.
C432682

Using a 27 mm deep socket wrench, install the oil pressure sensor to the rear transaxle case sub-assembly.

Torque:
20.6 N*m (210 kgf*cm, 15 ft.*lbf)

NOTICE:

Be careful not to damage the O-ring.



Hide 35151K 59.INSTALL AUTOMATIC TRANSMISSION CASE COVER

a.
C432681

Install the automatic transmission case cover to the transaxle case sub-assembly with the 2 clips.


Hide 89413T 60.INSTALL TRANSMISSION REVOLUTION SENSOR (NSS)

a.
C395501

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NSS).

NOTICE:

Ensure that the O-ring is not twisted.



b.
C432680

Install the transmission revolution sensor (NSS) to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.



Hide 89413N 61.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)

a.
C395501

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NT).

NOTICE:

Ensure that the O-ring is not twisted.



b.
C432679

Install the transmission revolution sensor (NT) to the rear transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.



Hide 89413M 62.INSTALL TRANSMISSION REVOLUTION SENSOR (NOUT)

a.
C395501

Coat a new O-ring with Toyota Genuine CVT fluid FE and install it to the transmission revolution sensor (NOUT).

NOTICE:

Ensure that the O-ring is not twisted.



b.
C432678

Install the transmission revolution sensor (NOUT) to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.



Hide 89419B 63.INSTALL SHIFT STROKE SENSOR

a.
C430123

Coat the O-ring of the shift stroke sensor with Toyota Genuine CVT fluid FE.

NOTICE:

If reusing the shift stroke sensor, check that the O-ring is not damaged.



b.
C432677

Install the shift stroke sensor to the transaxle case sub-assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Be careful not to damage the O-ring.



Hide 84540 64.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C432676

Temporarily install the park/neutral position switch assembly to the transaxle case sub-assembly with the 2 bolts.


b.
C432796

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


c.
C432797C01
0.76,1.573 0.948,1.802 0.188,0.229 10 true *a
*a N


Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.



d.

Remove the transmission control shaft lever from the manual valve lever shaft.


e.
C432798C01
2.479,0.615 2.885,0.375 2.885,0.375 2.49,0.448 true 2.917,0.26 3.167,0.521 0.25,0.26 10 false *a
*a Protrusion


Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


f.
C432676

Hold the park/neutral position switch assembly in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


g.
C430122

Install the transmission control shaft lever to the manual valve lever shaft with the washer and nut.

NOTICE:

Be careful of the direction of the transmission control shaft lever.


Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 33493C 65.INSTALL TRANSMISSION OIL COOLER ASSEMBLY

a.
C432673

Coat 2 new O-rings with Toyota Genuine CVT fluid FE and install them to the transaxle housing.

NOTICE:

Ensure that the O-rings are not twisted.



b.
C432672

Install the transmission oil cooler to the transaxle housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)