Home › Drivetrain › K320 (MULTIDRIVE / CVT) › FRONT DIFFERENTIAL OIL SEAL › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422058 FRONT DIFFERENTIAL OIL SEAL A

K320 MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front drive shaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of CVT fluid
w/ Stop and Start System:

Bleed air from oil pump (continuously variable transaxle assembly)


Stop and Start System (Click here)
ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)

PROCEDURE

Hide 43420H 3.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C428859E01
1.583,0.906 1.167,0.49 true 1.833,2.844 2,2.51 false 1.563,2.792 2.021,2.99 0.458,0.198 10 false SST 0.875,0.417 1.167,0.583 0.292,0.167 10 true SST

Using SST, remove the front drive shaft oil seal LH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C428860E01
0.906,0.604 1.24,0.979 false 2.167,2.833 2.281,2.573 false 1.917,2.781 2.375,2.979 0.458,0.198 10 false SST 0.656,0.542 1.115,0.74 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43420H 5.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C428862C01
1.74,2.271 2.073,2.146 false 1.729,0.792 1.313,0.375 true 2.104,2.083 2.563,2.281 0.458,0.198 10 false SST 1.021,0.302 1.313,0.469 0.292,0.167 10 true SST 2.063,2.656 2.521,2.854 0.458,0.198 10 false *a
*a Drive in Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the continuously variable transaxle assembly.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 43410M 6.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C428861C02
2.375,2.417 2.146,2.375 false 1.438,0.521 2.031,0.844 true 2.417,2.354 2.875,2.552 0.458,0.198 10 false SST 1.177,0.417 1.5,0.583 0.323,0.167 10 false SST 2.115,2.969 2.573,3.167 0.458,0.198 10 false *a
*a Drive in Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the continuously variable transaxle assembly.

SST
09223-00010  

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.