Home › Drivetrain › K320 (MULTIDRIVE / CVT) › SHIFT LEVER (for TMMF Made) › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0432243 SHIFT LEVER(for TMMF Made) G

K320 MULTIDRIVE / CVT  SHIFT LEVER(for TMMF Made)  INSPECTION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RHD and LHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 1.INSPECT SHIFT LOCK CONTROL ECU (w/ Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.


a.

Inspect the wire harness.

i.
C439390

Disconnect the shift lock control ECU connector.


ii.
C431707C01
1.417,0.25 1.917,0.5 0.5,0.25 2.156,1.458 2.51,1.229 2.51,1.229 2.646,1.229 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 2.708,1.177 2.917,1.354 0.208,0.177 10 false IG 1.552,0.302 2.01,0.5 0.458,0.198 10 false H20
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H20-5(IG) - Body ground Ignition switch ON 11 to 14 V
H20-5(IG) - Body ground Ignition switch off Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.
C431707C02
1.417,0.25 1.917,0.5 0.5,0.25 2.625,0.594 2.417,0.594 2.417,0.594 1.969,1.448 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 2.698,0.531 3.031,0.708 0.333,0.177 10 false STP 1.563,0.313 2.021,0.51 0.458,0.198 10 false H20
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H20-4(STP) - Body ground Brake pedal depressed 11 to 14 V
H20-4(STP) - Body ground Brake pedal released Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iv.
C431707C03
1.417,0.25 1.833,0.5 0.417,0.25 1.271,1.5 0.813,1.125 0.813,1.125 0.667,1.125 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 0.521,1.063 0.729,1.24 0.208,0.177 10 false E 1.521,0.313 1.979,0.51 0.458,0.198 10 false H20
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H20-1(E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Inspect shift lock solenoid:

i.
C439391

Disconnect the shift lock solenoid connector.


ii.
C197452C57
1.448,0.167 1.948,0.417 0.5,0.25 0.802,1.521 1.365,1.25 true 1.135,1.802 1.594,1.25 true 2.063,1.25 2.615,1.542 true 2.281,1.802 1.844,1.25 true 0.083,0.083 0.292,0.271 0.208,0.188 10 false *a 2.677,1.5 2.833,1.698 0.156,0.198 10 false P 2.333,1.74 2.583,1.927 0.25,0.188 10 false E2 0.771,1.75 1.198,1.938 0.427,0.188 10 false SLS- 0.438,1.469 0.885,1.667 0.448,0.198 10 false SLS+ 1.667,0.219 1.823,0.417 0.156,0.198 10 false A
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
A-4(P) - A-3(E2) Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω


If the result is not as specified, replace the shift lock control unit assembly.



Hide 2.INSPECT SHIFT LOCK CONTROL ECU (w/o Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.


a.

Inspect the wire harness.

i.
C439390

Disconnect the shift lock control ECU connector.


ii.
C333431C13
1.469,0.167 1.969,0.417 0.5,0.25 0.917,0.917 1.448,1.083 true 1.969,1.083 2.5,0.917 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.615,0.844 1.073,1.042 0.458,0.198 10 false ACC 2.542,0.844 3,1.042 0.458,0.198 10 false IG 1.615,0.219 2.073,0.417 0.458,0.198 10 false H19
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-1(ACC) - Body ground Ignition switch ACC 11 to 14 V
H19-1(ACC) - Body ground Ignition switch off Below 1 V
H19-4(IG) - Body ground Ignition switch ON 11 to 14 V
H19-4(IG) - Body ground Ignition switch off Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.
C333431C14
1.458,0.167 1.958,0.417 0.5,0.25 1.969,1.333 2.5,1.5 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.542,1.438 3,1.635 0.458,0.198 10 false STP 1.583,0.229 2.042,0.427 0.458,0.198 10 false H19
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
8 (STP) - Body ground Ignition switch ON, brake pedal depressed 11 to 14 V
8 (STP) - Body ground Ignition switch ON, brake pedal released Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iv.
C333431C15
1.448,0.167 1.948,0.417 0.5,0.25 1.792,1.365 2.25,1.76 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.313,1.719 2.469,1.917 0.156,0.198 10 false E 1.573,0.219 2.031,0.417 0.458,0.198 10 false H19
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-7(E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Inspect key interlock solenoid operation signal:

i.
C439390

Connect the shift lock control ECU connector.


ii.
C440008C01
1.333,1.75 1.833,2 0.5,0.25 1.844,2.99 2.229,2.99 true 0.594,1.688 0.844,1.938 0.25,0.25 10 false *a 2.271,2.875 2.688,3.073 0.417,0.198 10 false KLS+ 1.458,1.802 1.917,2 0.458,0.198 10 false H19
*a Component with harness connected
(Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
5 (KLS+) - Body ground Ignition switch ACC and shift lever not in P 11 to 14 V


HINT:

Do not disconnect the shift lock control ECU connector.


If the result is not as specified, replace the shift lock control unit assembly.



c.

Inspect shift lock solenoid:

i.
C439391

Disconnect the shift lock solenoid connector.


ii.
C197452C59
1.448,0.167 1.948,0.417 0.5,0.25 0.802,1.521 1.365,1.25 true 1.135,1.802 1.594,1.25 true 2.063,1.25 2.615,1.542 true 2.281,1.802 1.844,1.25 true 0.083,0.083 0.292,0.271 0.208,0.188 10 false *a 2.677,1.5 2.833,1.698 0.156,0.198 10 false P 2.333,1.74 2.583,1.927 0.25,0.188 10 false E2 0.771,1.75 1.198,1.938 0.427,0.188 10 false SLS- 0.438,1.469 0.885,1.667 0.448,0.198 10 false SLS+ 1.667,0.208 1.823,0.406 0.156,0.198 10 false A
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
A-4(P) - A-3(E2) Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω


If the result is not as specified, replace the shift lock control unit assembly.



Hide 3.INSPECT TRANSMISSION CONTROL SWITCH (for LHD)

a.
C439392

Disconnect the transmission control switch connector.


b.
C401772C04
0.677,1.542 1.24,1.271 true 1.031,1.771 1.49,1.281 true 2.75,1.531 2.188,1.26 true 2.438,1.771 1.979,1.281 true 1.802,1.781 1.729,1.292 true 1.646,1.813 2.146,2.01 0.5,0.198 10 false SFTU 2.49,1.729 2.667,1.917 0.177,0.188 10 false E 2.813,1.458 3.25,1.656 0.438,0.198 10 false SFTD 0.531,1.479 0.708,1.688 0.177,0.208 10 false S 0.073,0.052 0.292,0.25 0.219,0.198 10 false *a 0.865,1.719 1.219,1.927 0.354,0.208 10 false IG
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.


Hide 4.INSPECT TRANSMISSION CONTROL SWITCH (for RHD)

a.
C439393

Disconnect the transmission control switch connector.


b.
C401772C08
1.417,0.25 1.917,0.5 0.5,0.25 0.677,1.542 1.24,1.271 true 1.031,1.771 1.49,1.281 true 2.75,1.531 2.188,1.26 true 2.438,1.771 1.979,1.281 true 1.802,1.781 1.729,1.292 true 1.646,1.813 2.146,2.01 0.5,0.198 10 false SFTD 2.49,1.729 2.667,1.917 0.177,0.188 10 false E 2.813,1.458 3.25,1.656 0.438,0.198 10 false SFTU 0.531,1.479 0.708,1.688 0.177,0.208 10 false S 0.073,0.052 0.292,0.25 0.219,0.198 10 false *a 0.865,1.719 1.219,1.927 0.354,0.208 10 false IG 1.531,0.292 1.99,0.49 0.458,0.198 10 false H64
*a Component without harness connected
(Transmission Control Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
Shift lever not in M, "+" or "-" 10 kΩ or higher
1 (SFTU) - 2 (E) Shift lever held in "+"
(Up-shift)
Below 1 Ω
Shift lever not held in "+"
(Up-shift)
10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-"
(Down-shift)
Below 1 Ω
Shift lever not held in "-"
(Down-shift)
10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.