|
*1: Connect the GTS to the DLC3 when measuring the fluid pressure. *2: Depress the accelerator pedal at a consistent angle to maintain the specified vehicle speed. |
||
| Engine stall speed | D | 2300 +/- 400 rpm |
| Fluid pressure (Throttle valve fully opened)*1 | ||
| Engine stall speed
2300 +/- 400 rpm |
D | 3400 to 4200 kPa (34.7 to 42.8 kgf/cm2, 493 to 609 psi) |
| R | 2400 to 3200 kPa (24.5 to 32.6 kgf/cm2, 348 to 464 psi) | |
| Time lag | N → D | Less than 1.2 seconds |
| N → R | Less than 1.5 seconds | |
| Engine idle speed (A/C off) | N | 850 to 950 rpm |
| Shift schedule (D) (NORMAL) | ||
| Throttle valve position (100%) | Fully depressed
(Before 1st up-shift) |
6050 to 6900 rpm |
| Fully depressed
(Highest engine speed after the 1st up-shift) |
6100 to 6900 rpm | |
| Throttle valve position (Constant opening angle)*2 | 30 km/h (19 mph) | 900 to 1350 rpm |
| 70 km/h (43 mph) | 1150 to 1650 rpm | |
| 100 km/h (62 mph) | 1800 to 2300 rpm | |
| Kick down | Accelerating from 20 km/h (12 mph) | 2000 rpm or more |
| Shift schedule (D) (PWR) | ||
| Throttle valve position (100%) | Fully depressed
(Before 1st up-shift) |
6050 to 6900 rpm |
| Fully depressed
(Highest engine speed after the 1st up-shift) |
6100 to 6900 rpm | |
| Throttle valve position (Constant opening angle)*2 | 30 km/h (19 mph) | 1500 to 1950 rpm |
| 70 km/h (43 mph) | 2100 to 2600 rpm | |
| 100 km/h (62 mph) | 2500 to 3000 rpm | |
| Kick down | Accelerating from 20 km/h (12 mph) | 2000 rpm or more |
| Lock-up point | ||
| Lock-up ON
(Accelerator pedal opening 5%) |
D | 10 to 30 km/h (6 to 19 mph) |
| Lock-up OFF
(Accelerator pedal opening 0%) |
D | 5 to 20 km/h (3 to 12 mph) |
|
*1: Connect the GTS to the DLC3 when measuring the fluid pressure. *2: Depress the accelerator pedal at a consistent angle to maintain the specified vehicle speed. |
||
| Engine stall speed | D | 2300 +/- 400 rpm |
| Fluid pressure (Throttle valve fully opened)*1 | ||
| Engine stall speed
2300 +/- 400 rpm |
D | 3400 to 4200 kPa (34.7 to 42.8 kgf/cm2, 493 to 609 psi) |
| R | 2400 to 3200 kPa (24.5 to 32.6 kgf/cm2, 348 to 464 psi) | |
| Time lag | N → D | Less than 1.2 seconds |
| N → R | Less than 1.5 seconds | |
| Engine idle speed (A/C off) | N | 850 to 950 rpm |
| Shift schedule (D) (NORMAL) | ||
| Throttle valve position (100%) | Fully depressed
(Before 1st up-shift) |
6050 to 6900 rpm |
| Fully depressed
(Highest engine speed after the 1st up-shift) |
6100 to 6900 rpm | |
| Throttle valve position (Constant opening angle)*2 | 30 km/h (19 mph) | 900 to 1350 rpm |
| 70 km/h (43 mph) | 1150 to 1650 rpm | |
| 100 km/h (62 mph) | 1750 to 2250 rpm | |
| Kick down | Accelerating from 20 km/h (12 mph) | 2000 rpm or more |
| Shift schedule (D) (PWR) | ||
| Throttle valve position (100%) | Fully depressed
(Before 1st up-shift) |
6050 to 6900 rpm |
| Fully depressed
(Highest engine speed after the 1st up-shift) |
6100 to 6900 rpm | |
| Throttle valve position (Constant opening angle)*2 | 30 km/h (19 mph) | 1500 to 1950 rpm |
| 70 km/h (43 mph) | 2100 to 2600 rpm | |
| 100 km/h (62 mph) | 2450 to 2950 rpm | |
| Kick down | Accelerating from 20 km/h (12 mph) | 2000 rpm or more |
| Lock-up point | ||
| Lock-up ON
(Accelerator pedal opening 5%) |
D | 10 to 30 km/h (6 to 19 mph) |
| Lock-up OFF
(Accelerator pedal opening 0%) |
D | 5 to 20 km/h (3 to 12 mph) |
|
*: Using CVT (Continuously Variable Transaxle) fluid other than the above type may cause abnormal noise or vibration, or damage the CVT (Continuously Variable Transaxle) of your vehicle. |
|||
| Dry fill | w/o Stop and Start System | 8.44 liters (8.92 US qts, 7.43 Imp. qts) | Toyota Genuine CVT fluid FE* |
| w/ Stop and Start System | 8.12 liters (8.6 US qts, 7.1 Imp. qts) | ||
| Input shaft sub-assembly | Standard input shaft end play | 0.387 to 1.400 mm (0.0152 to 0.0551 in.) | |
| Clearance of C-1 clutch | Pack clearance (Reference) | 0.45 to 0.75 mm (0.0177 to 0.0295 in.) | |
| Forward clutch flange thickness | Part number | Thickness (mm (in.)) | Mark |
| 35635-12410 (35635-K0010) | 3.5 (0.138) | 0 | |
| 35635-12420 (35635-K0020) | 3.6 (0.142) | 1 | |
| 35635-12430 (35635-K0030) | 3.7 (0.146) | 2 | |
| 35635-12440 (35635-K0040) | 3.8 (0.150) | 3 | |
| 35635-12450 (35635-K0050) | 3.9 (0.154) | 4 | |
| 35635-12460 (35635-K0060) | 4.0 (0.157) | 5 | |
| 35635-12470 (35635-K0070) | 4.1 (0.161) | 6 | |
| Forward clutch return spring sub-assembly | Standard free length | 18.54 mm (0.730 in.) | |
| Planetary gear assembly | Standard clearance | 0.16 to 0.61 mm (0.00630 to 0.0240 in.) | |
| Clearance of No. 1 brake | Pack clearance | 0.54 to 1.32 mm (0.0213 to 0.0520 in.) | |
| 1st and reverse brake return spring sub-assembly | Standard free length | 15.70 mm (0.618 in.) | |
| Thrust needle roller bearing and thrust bearing race diameter | Mark | Thrust bearing race diameter inside / outside
mm (in.) |
Thrust bearing race diameter inside / outside
mm (in.) |
| A | - | 47.75 (1.88) / 65.8 (2.59) | |
| B | 26.38 (1.04) / 38.9 (1.53) | 24.9 (0.98) / 38.9 (1.53) | |
| C | - | 29.7 (1.17) / 49.1 (1.93) | |
| Straight pin | Protrusion height | 7.0 to 8.0 mm (0.276 to 0.315 in.) | |
| Differential case tapered roller bearing preload (at 10 rpm) | Standard turning torque | 1.61 to 2.57 N*m (17 to 26 kgf*cm, 15 to 22 in.*lbf) | |
| Shim thickness | Part number | Thickness (mm (in.)) | |
| 90564-58002 | 1.76 (0.0693) | ||
| 90564-58003 | 1.79 (0.0705) | ||
| 90564-58004 | 1.82 (0.0717) | ||
| 90564-58005 | 1.85 (0.0728) | ||
| 90564-58006 | 1.88 (0.0740) | ||
| 90564-58007 | 1.91 (0.0752) | ||
| 90564-58008 | 1.94 (0.0764) | ||
| 90564-58009 | 1.97 (0.0776) | ||
| 90564-58010 | 2.00 (0.0787) | ||
| 90564-58011 | 2.03 (0.0799) | ||
| 90564-58012 | 2.06 (0.0811) | ||
| 90564-58013 | 2.09 (0.0823) | ||
| 90564-58014 | 2.12 (0.0835) | ||
| 90564-58015 | 2.15 (0.0846) | ||
| 90564-58016 | 2.18 (0.0858) | ||
| 90564-58017 | 2.21 (0.0870) | ||
| 90564-58018 | 2.24 (0.0882) | ||
| 90564-58019 | 2.27 (0.0894) | ||
| 90564-58020 | 2.30 (0.0906) | ||
| 90564-58021 | 2.33 (0.0917) | ||
| Adjust reduction driven gear tapered roller bearing preload (at 10 rpm) | Standard turning torque | Differential case tapered roller bearing preload + 2.63 to 4.88 N*m (27 to 49 kgf*cm, 2 to 3 ft.*lbf) | |
| Shim thickness | Part number | Thickness (mm (in.)) | Mark |
| 90564-44074 | 1.71 (0.0673) | E | |
| 90564-44075 | 1.74 (0.0685) | F | |
| 90564-44076 | 1.77 (0.0697) | G | |
| 90564-44077 | 1.80 (0.0709) | H | |
| 90564-44078 | 1.83 (0.0720) | J | |
| 90564-44079 | 1.86 (0.0732) | K | |
| 90564-44080 | 1.89 (0.0744) | L | |
| 90564-44081 | 1.92 (0.0756) | M | |
| 90564-44082 | 1.95 (0.0768) | N | |
| 90564-44083 | 1.98 (0.0780) | P | |
| 90564-44084 | 2.01 (0.0791) | Q | |
| 90564-44085 | 2.04 (0.0803) | R | |
| 90564-44086 | 2.07 (0.0815) | S | |
| 90564-44087 | 2.10 (0.0827) | T | |
| 90564-44088 | 2.13 (0.0839) | U | |
| 90564-44089 | 2.16 (0.0850) | V | |
| 90564-44090 | 2.19 (0.0862) | W | |
| 90564-44091 | 2.22 (0.0874) | X | |
| 90564-44092 | 2.25 (0.0886) | Y | |
| 90564-44093 | 2.28 (0.0898) | - | |
| 90564-44094 | 2.31 (0.0909) | - | |
| 90564-44095 | 2.34 (0.0921) | - | |
| 90564-44096 | 2.37 (0.0933) | - | |
| Front drive shaft oil seal LH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Transaxle housing type T oil seal | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Front drive shaft oil seal RH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) | |
| Drive plate runout | Maximum | 0.30 mm (0.0118 in.) |
| Front drive shaft oil seal LH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) |
| Front drive shaft oil seal RH | Standard depth | -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) |
| Transmission revolution sensor (NT) | ||
| Tester Connection | Condition | Specified Condition |
| 1 (NTO) - 2 (NTB) | Low signal | 4 to 8 mA |
| High signal | 12 to 16 mA | |
| Transmission revolution sensor (NOUT) | ||
| Tester Connection | Condition | Specified Condition |
| 1 (NOO) - 2 (NOB) | Low signal | 4 to 8 mA |
| High signal | 12 to 16 mA | |
| Transmission revolution sensor (NSS) | ||
| Tester Connection | Condition | Specified Condition |
| 1 (NSSO) - 2 (NSSB) | Low signal | 4 to 8 mA |
| High signal | 12 to 16 mA | |
| Shift stroke sensor | ||
| Standard voltage (Combined dry-cell battery voltage of 4.5 V) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (VOUT) - 3 (GND) | High signal | 4.09 to 4.19 V |
| Low signal | 0.36 to 0.45 V | |
| Reference voltage (Combined dry-cell battery voltage of 5.0 V) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (VOUT) - 3 (GND) | High signal | 4.55 to 4.65 V |
| Low signal | 0.4 to 0.5 V | |
| Park/neutral position switch assembly | ||
| Tester Connection | Condition | Specified Condition |
| 4 (B) - 5 (L) | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P and N | 10 kΩ or higher | |
| 2 (RB) - 6 (PL) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 2 (RB) - 1 (RL) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 2 (RB) - 9 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 2 (RB) - 7 (DL) | Shift lever in D, M, "+" or "-" | Below 1 Ω |
| Shift lever not in D, M, "+" or "-" | 10 kΩ or higher | |
| 2 (RB) - 3 (2L) | Shift lever in B | Below 1 Ω |
| Shift lever not in B | 10 kΩ or higher | |
| Shift lock control ECU (w/ Smart Entry and Start System) | ||
| Wire harness: | ||
| Tester Connection | Condition | Specified Condition |
| 5 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 4 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 1 (E) - Body ground | Always | Below 1 Ω |
| Shift lock solenoid: | ||
| Tester Connection | Condition | Specified Condition |
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω | |
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
| Shift lock control ECU (w/o Smart Entry and Start System) | ||
| Wire harness: | ||
| Tester Connection | Condition | Specified Condition |
| 1 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 8 (STP) - Body ground | Ignition switch ON, brake pedal depressed | 11 to 14 V |
| Ignition switch ON, brake pedal released | Below 1 V | |
| 4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 7 (E) - Body ground | Always | Below 1 Ω |
| 5 (KLS+) - Body ground | Ignition switch ACC and shift lever in P | Below 1 V |
| Ignition switch ACC and shift lever not in P | 11 to 14 V | |
| Shift lock solenoid: | ||
| Tester Connection | Condition | Specified Condition |
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω | |
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
| Transmission control switch | ||
| Tester Connection | Condition | Specified Condition |
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| 1 (SFTU) - 2 (E) | Shift lever held in "+"
(Up-shift) |
Below 1 Ω |
| Shift lever not held in "+"
(Up-shift) |
10 kΩ or higher | |
| 3 (SFTD) - 2 (E) | Shift lever held in "-"
(Down-shift) |
Below 1 Ω |
| Shift lever not held in "-"
(Down-shift) |
10 kΩ or higher | |
| Shift lock control ECU (w/ Smart Entry and Start System) | ||
| Wire harness: | ||
| Tester Connection | Condition | Specified Condition |
| 5 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 4 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| Brake pedal released | Below 1 V | |
| 1 (E) - Body ground | Always | Below 1 Ω |
| Shift lock solenoid: | ||
| Tester Connection | Condition | Specified Condition |
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω | |
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
| Shift lock control ECU (w/o Smart Entry and Start System) | ||
| Wire harness: | ||
| Tester Connection | Condition | Specified Condition |
| 1 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 8 (STP) - Body ground | Ignition switch ON, brake pedal depressed | 11 to 14 V |
| Ignition switch ON, brake pedal released | Below 1 V | |
| 4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |
| 7 (E) - Body ground | Always | Below 1 Ω |
| 5 (KLS+) - Body ground | Ignition switch ACC and shift lever in P | Below 1 V |
| Ignition switch ACC and shift lever not in P | 11 to 14 V | |
| Shift lock solenoid: | ||
| Tester Connection | Condition | Specified Condition |
| 4 (P) - 3 (E2) | Shift lever in P | 10 kΩ or higher |
| Shift lever not in P | Below 1 Ω | |
| 1 (SLS+) - 2 (SLS-) | Always | 112 Ω |
| Transmission control switch (for LHD) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| 3 (SFTU) - 2 (E) | Shift lever held in "+"
(Up-shift) |
Below 1 Ω |
| Shift lever not held in "+"
(Up-shift) |
10 kΩ or higher | |
| 1 (SFTD) - 2 (E) | Shift lever held in "-"
(Down-shift) |
Below 1 Ω |
| Shift lever not held in "-"
(Down-shift) |
10 kΩ or higher | |
| Transmission control switch (for RHD) | ||
| Tester Connection | Condition | Specified Condition |
| 4 (IG) - 5 (S) | Shift lever in M, "+" or "-" | Below 1 Ω |
| Shift lever not in M, "+" or "-" | 10 kΩ or higher | |
| 1 (SFTU) - 2 (E) | Shift lever held in "+"
(Up-shift) |
Below 1 Ω |
| Shift lever not held in "+"
(Up-shift) |
10 kΩ or higher | |
| 3 (SFTD) - 2 (E) | Shift lever held in "-"
(Down-shift) |
Below 1 Ω |
| Shift lever not held in "-"
(Down-shift) |
10 kΩ or higher | |
| No. 1 transmission shift switch assembly | ||
| Tester Connection | Condition | Specified Condition |
| 1 (SDN) - 2 (ECC) | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher | |
| 1 (SDN) - 3 (ECC1) | "-" (Down shift) shift paddle switch operated and held | Below 2.5 Ω |
| "-" (Down shift) shift paddle switch not operated | 1 MΩ or higher | |
| No. 2 transmission shift switch assembly | ||
| Tester Connection | Condition | Specified Condition |
| 1 (SUP) - 2 (ECC) | "+" (Up shift) shift paddle switch operated and held | Below 2.5 Ω |
| "+" (Up shift) shift paddle switch not operated | 1 MΩ or higher | |
| Combination switch assembly | ||
| Tester Connection | Condition | Specified Condition |
| 8 (MSW1) - 5 (E) | Switch pushed | Below 1 Ω |
| Switch not pushed | 10 kΩ or higher | |
| Measurement Condition | Specified Condition | |
| Battery positive (+) → 4 (ILL+) | Illuminates | |
| Battery negative (-) → 1 (ILL-) | ||
| Shift solenoid valve (SLG, SL1, SL2, SLU, SLP, SLS) | ||
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |