Home › Drivetrain › P910 (HYBRID TRANSMISSION / TRANSAXLE) › SHIFT LEVER (for TMC Made) › from 2020.07
RM36W0E _52 Drivetrain _088636 P910 HYBRID TRANSMISSION / TRANSAXLE _0432251 SHIFT LEVER(for TMC Made) G

P910 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER(for TMC Made)  INSPECTION  


PROCEDURE

Hide 1.INSPECT SHIFT LOCK CONTROL ECU (w/ Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.


a.

Inspect the wire harness.

i.
C429246

Disconnect the shift lock control ECU connector.


ii.
C431707C04
1.417,0.25 1.917,0.5 0.5,0.25 2.156,1.458 2.51,1.229 2.51,1.229 2.646,1.229 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 2.708,1.177 2.917,1.354 0.208,0.177 10 false IG 1.552,0.302 2.01,0.5 0.458,0.198 10 false H20
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H20-5(IG) - Body ground Ignition switch ON 11 to 14 V
H20-5(IG) - Body ground Ignition switch off Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.
C431707C05
1.417,0.25 1.917,0.5 0.5,0.25 2.625,0.594 2.417,0.594 2.417,0.594 1.969,1.448 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 2.698,0.531 3.031,0.708 0.333,0.177 10 false STP 1.563,0.313 2.021,0.51 0.458,0.198 10 false H20
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H20-4(STP) - Body ground Ready ON, brake pedal depressed 11 to 14 V
H20-4(STP) - Body ground Ready ON, brake pedal released Below 1 V


If the result is not as specified, repair or replace the wire harness or connector or replace the hybrid vehicle control ECU assembly.


iv.
C431707C06
1.417,0.25 1.833,0.5 0.417,0.25 1.271,1.5 0.813,1.125 0.813,1.125 0.667,1.125 true 0.104,0.104 0.292,0.281 0.188,0.177 10 false *a 0.521,1.063 0.729,1.24 0.208,0.177 10 false E 1.521,0.313 1.979,0.51 0.458,0.198 10 false H20
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H20-1(E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Inspect shift lock solenoid:

i.
C429245

Disconnect the shift lock solenoid connector.


ii.
C197452C57
1.448,0.167 1.948,0.417 0.5,0.25 0.802,1.521 1.365,1.25 true 1.135,1.802 1.594,1.25 true 2.063,1.25 2.615,1.542 true 2.281,1.802 1.844,1.25 true 0.083,0.083 0.292,0.271 0.208,0.188 10 false *a 2.677,1.5 2.833,1.698 0.156,0.198 10 false P 2.333,1.74 2.583,1.927 0.25,0.188 10 false E2 0.771,1.75 1.198,1.938 0.427,0.188 10 false SLS- 0.438,1.469 0.885,1.667 0.448,0.198 10 false SLS+ 1.667,0.219 1.823,0.417 0.156,0.198 10 false A
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
A-4(P) - A-3(E2) Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω


If the result is not as specified, replace the shift lock control unit assembly.



Hide 2.INSPECT SHIFT LOCK CONTROL ECU (w/o Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.


a.

Inspect the wire harness.

i.
C429246

Disconnect the shift lock control ECU connector.


ii.
C333431C13
1.469,0.167 1.969,0.417 0.5,0.25 0.917,0.917 1.448,1.083 true 1.969,1.083 2.5,0.917 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 0.615,0.844 1.073,1.042 0.458,0.198 10 false ACC 2.542,0.844 3,1.042 0.458,0.198 10 false IG 1.615,0.219 2.073,0.417 0.458,0.198 10 false H19
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-1(ACC) - Body ground Ignition switch ACC 11 to 14 V
H19-1(ACC) - Body ground Ignition switch off Below 1 V
H19-4(IG) - Body ground Ignition switch ON 11 to 14 V
H19-4(IG) - Body ground Ignition switch off Below 1 V


If the result is not as specified, repair or replace the shift lock control ECU wire harness.


iii.
C333431C14
1.458,0.167 1.958,0.417 0.5,0.25 1.969,1.333 2.5,1.5 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.542,1.438 3,1.635 0.458,0.198 10 false STP 1.583,0.229 2.042,0.427 0.458,0.198 10 false H19
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-8(STP) - Body ground Ignition switch ON, brake pedal depressed 11 to 14 V
H19-8(STP) - Body ground Ignition switch ON, brake pedal released Below 1 V


If the result is not as specified, repair or replace the wire harness or connector or replace the hybrid vehicle control ECU assembly.


iv.
C333431C15
1.448,0.167 1.948,0.417 0.5,0.25 1.792,1.365 2.25,1.76 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.313,1.719 2.469,1.917 0.156,0.198 10 false E 1.573,0.219 2.031,0.417 0.458,0.198 10 false H19
*a Front view of wire harness connector
(to Shift Lock Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-7(E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the shift lock control ECU wire harness.



b.

Inspect key interlock solenoid operation signal:

i.
C429246

Connect the shift lock control ECU connector.


ii.
C431708C03
1.479,1.75 1.979,2 0.5,0.25 2.01,2.958 2.396,2.958 true 0.781,1.698 1.031,1.948 0.25,0.25 10 false *a 2.458,2.896 2.875,3.094 0.417,0.198 10 false KLS+ 1.615,1.802 2.073,2 0.458,0.198 10 false H19
*a Component with harness connected
(Shift Lock Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-5(KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
H19-5(KLS+) - Body ground Ignition switch ACC and shift lever not in P 11 to 14 V


HINT:

Do not disconnect the shift lock control ECU connector.


If the result is not as specified, replace the shift lock control unit assembly.



c.

Inspect shift lock solenoid:

i.
C429245

Disconnect the shift lock solenoid connector.


ii.
C197452C58
1.448,0.167 1.948,0.417 0.5,0.25 0.802,1.521 1.365,1.25 true 1.135,1.802 1.594,1.25 true 2.063,1.25 2.615,1.542 true 2.281,1.802 1.844,1.25 true 0.083,0.083 0.292,0.271 0.208,0.188 10 false *a 2.677,1.5 2.833,1.698 0.156,0.198 10 false P 2.333,1.74 2.583,1.927 0.25,0.188 10 false E2 0.771,1.75 1.198,1.938 0.427,0.188 10 false SLS- 0.438,1.469 0.885,1.667 0.448,0.198 10 false SLS+ 1.667,0.219 1.823,0.417 0.156,0.198 10 false A
*a Front view of wire harness connector
(to Shift Lock Solenoid)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4(P) - A-3(E2) Shift lever in P 10 kΩ or higher
A-4(P) - A-3(E2) Shift lever not in P Below 1 Ω
A-1(SLS+) - A-2(SLS-) Always 112 Ω


If the result is not as specified, replace the shift lock control unit assembly.