Home › Brake › BRAKE SYSTEM (OTHER) › VACUUM PUMP (for TMC Made) › 2020.07–2020.09
RM36W0E _54 Brake _088656 BRAKE SYSTEM (OTHER) _0432281 VACUUM PUMP(for TMC Made) A

BRAKE SYSTEM (OTHER)  VACUUM PUMP(for TMC Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during vacuum pump assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

*2: w/ Gasoline Particulate Filter

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
If possible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
If impossible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


GPF Deposition Values*2

-

GPF deposition values save

-

GPF deposition values write



·

MIL comes on

·

Deterioration of fuel efficiency


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 44777 2.DISCONNECT NO. 1 VACUUM HOSE CONNECTOR

a.
C435064C01
2.542,3.625 2.177,3.771 2.177,3.771 2.542,3.365 true 2.042,3.75 2.354,3.906 0.313,0.156 10 false *a
*a Retainer
V100135

Pinch
V113148

Pull off


Pinch the retainer of the No. 1 vacuum hose connector, and then pull the No. 1 vacuum hose connector off of the vacuum pump assembly.

NOTICE:

Be sure to disconnect the No. 1 vacuum hose connector by hand.



Hide 77261D 3.SEPARATE FUEL TANK TO CANISTER TUBE

a.
C435065

Separate the fuel tank to canister tube.


Hide 82121 4.SEPARATE ENGINE WIRE

a.
C435066

Disconnect the 2 connectors.


b.

Remove the 4 bolts and separate the engine wire.


c.
C435067

Disconnect the 2 connectors.


d.

Remove the bolt and separate the engine wire.


e.

Disengage the clamp to separate the engine wire.


f.
C435068

Disconnect the 6 connectors.


g.

Disengage the 2 clamps to separate the engine wire.


h.
C435069

Disconnect the connector.


i.

Remove the bolt and clamp to separate the engine wire.


Hide 29300 5.REMOVE VACUUM PUMP ASSEMBLY

a.
C435070

Using an 8 mm socket wrench, remove the 3 bolts and vacuum pump assembly from the engine assembly.


b.
C435071

Remove the No. 1 vacuum pump O-ring from the vacuum pump assembly.