Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  UTILITY  


DESCRIPTION


a.

Refer to the table below and then perform the necessary operation according to the part to be replaced in order to perform calibration.

Parts to be Replaced / Operation Necessary Operation
Skid control ECU (brake actuator assembly) Perform yaw rate and acceleration sensor zero point calibration and store system information.
Yaw rate and acceleration sensor (airbag sensor assembly)
1.

Perform "Reset Memory".

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information memorization.


Wheel alignment adjustment
1.

Perform "Reset Memory".

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information memorization.





UTILITY ITEMS


Utility Items Main Purpose Link
All Readiness Confirm if DTC judgment has been completed. Refer to utility
Calibration Enter Dealer Mode (Calibration) and perform yaw rate and acceleration sensor zero point calibration and system information memorization. Refer to utility
Inspection Mode Enter Inspection Mode which prohibits operation of VSC and TRC. Refer to utility
Signal Check Enter Dealer Mode (Signal Check) and perform a signal inspection of the electronically controlled brake system. (Click here)
Vehicle Control History (RoB) View vehicle control history. (Click here)
Reset Memory Clear yaw rate and acceleration sensor zero point calibration data and system information. Refer to utility


ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Operate the GTS to clear the codes even if no DTCs are stored.

Chassis > Brake > Clear DTCs
50002 435
Chassis > Steering Angle Sensor > Clear DTCs
50002 445

b.

Press the DTC clear button.


c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform the DTC judgment driving pattern to run the DTC judgment.


f.

Operate the GTS to select "All Readiness".

Chassis > Brake > Utility
Tester Display
All Readiness
50005 435 20
Chassis > Steering Angle Sensor > Utility
Tester Display
All Readiness
50005 445 20

g.

Input the DTC to be confirmed.


h.

Check the DTC judgment result.

GTS Display Description
Normal
·

DTC judgment completed

·

System normal


Abnormal
·

DTC judgment completed

·

System abnormal


Incomplete
·

DTC judgment not completed

·

Perform the driving pattern


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

·

Perform the driving pattern



If the judgment result shows Incomplete or N/A, perform the DTC confirmation driving pattern again.



CALIBRATION


NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform "Calibration" after performing "Reset Memory".

·

As the yaw rate and acceleration sensor zero point cannot be stored again until the current zero point is cleared, perform "Reset Memory" and "Calibration" after replacing or removing and installing the yaw rate and acceleration sensor (airbag sensor assembly).

·

While obtaining the zero point, keep the vehicle stationary and do not vibrate, tilt, move, or shake it.

·

Be sure to perform this procedure on a level surface (with an inclination of less than 0.2 degrees).

·

While obtaining the zero point, make sure the tire pressure is as specified and the vehicle is in full contact with the ground (not lifted up or loaded).



HINT:

When entering Dealer Mode (Calibration), the skid control ECU (brake actuator assembly) communicates with the forward recognition camera to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Dealer Mode (Calibration) within 5 seconds of entering Dealer Mode (Calibration) (w/ Pre-collision System).


a.

Clear the zero point calibration data and system information.

i.

Turn the ignition switch off.


ii.

Apply the parking brake (for manual transaxle).


iii.

Check that the shift lever is in P (for CVT).


iv.

Check that the shift lever is in N (for manual transaxle).


v.

Using the GTS, select the skid control ECU (brake actuator assembly) to clear the zero point calibration data using the GTS.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560

vi.

Perform "Reset Memory".

NOTICE:

After perform "Reset Memory", the ABS warning light, brake system warning light (red indicator) and slip indicator light illuminate. If the vehicle is driven with the memory cleared, DTCs C051D54, C056054 or C121054 will be stored.




b.

Perform "Calibration".

HINT:
·

Yaw rate and acceleration sensor zero point calibration and store system information memorization are automatically performed immediately after Dealer Mode (Calibration) is entered.

·

If store system information memorization has not yet been performed, the slip indicator light will remain on.

·

If yaw rate and acceleration sensor zero point calibration is not successful, the slip indicator light will remain on and DTC C051D54 will be stored.

·

If system information data stored and that provided from other systems are not match, DTC U030057 or U130857 will be stored.



i.

Turn the ignition switch off.


ii.

Apply the parking brake (for manual transaxle).


iii.

Check that the shift lever is in P (for CVT).


iv.

Check that the shift lever is in N (for manual transaxle).


v.

Check that the steering wheel is centered.


vi.

Using the GTS, switch the skid control ECU (brake actuator assembly) to Dealer Mode (Calibration).

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

vii.

Perform "Calibration".


viii.

Confirm that the ABS warning light and slip indicator light indicate the Dealer Mode pattern (blinking at 0.25 second intervals).

HINT:
·

After "Calibration" has successfully completed, the ABS warning light and slip indicator light indicate the Dealer Mode pattern (blinking at 0.25 second intervals).

·

The slip indicator light may illuminate for approximately 7 seconds before learning successfully completes.

·

Do not exit Dealer Mode (Calibration) within 5 seconds of entering Dealer Mode (Calibration). If Dealer Mode (Calibration) is exited within 5 seconds of entering Dealer Mode (Calibration), enter Dealer Mode (Calibration) again, wait at least 5 seconds, then recheck for DTCs (w/ Pre-collision System).




ix.

Turn the ignition switch off.




INSPECTION MODE (WHEN USING GTS)


a.

Activating Inspection Mode

NOTICE:
·

Inspection Mode will be canceled when the ignition switch is turned off. Make sure to enter Inspection Mode again if the inspection is continued after the ignition switch is turned off.

·

Never drive the vehicle while in Inspection Mode.



i.

Ensure that the ignition switch is off and the engine is stopped.


ii.

Using the GTS, switch the skid control ECU (brake actuator assembly) to Inspection Mode.

Chassis > Brake > Utility
Tester Display
Inspection Mode
50005 435 4555

iii.

Check that the VSC OFF indicator light comes on and "Traction Control Turned OFF" is displayed on the multi-information display (Confirm that the system has entered Inspection Mode).



b.

End of Inspection Mode.

i.

Turning the ignition switch off ends Inspection Mode.

NOTICE:

If the ignition switch is turned to ON within 60 seconds of being turned off, the system will reenter Inspection Mode.



ii.

Confirm that the VSC OFF indicator light turns off and the "Traction Control Turned OFF" on the multi-information display is cleared (Confirm that Inspection Mode is canceled).




INSPECTION MODE (WHEN NOT USING GTS)


a.

Activating Inspection Mode

NOTICE:
·

Inspection Mode will be canceled when the ignition switch is turned off. Make sure to enter Inspection Mode again if the inspection is continued after the ignition switch is turned off.

·

Never drive the vehicle while in Inspection Mode.



i.

Perform steps "D" to "H" within 30 seconds.


ii.

Ensure that the ignition switch is off and the engine is stopped (Step "A").


iii.

Apply the parking brake (for manual transaxle) (Step "B").


iv.

Make sure that the shift lever is in P (for CVT) (Step "C").


v.

Make sure that the shift lever is in N (for manual transaxle) (Step "C").


vi.

Start the engine (Step "D").


vii.

Depress and release the brake pedal twice (Step "E").


viii.

While holding the brake pedal down, release and apply the parking brake twice (Step "F").


ix.

With the parking brake applied, depress and release the brake pedal twice (Step "G").


x.

Check that the VSC OFF indicator light comes on and "Traction Control Turned OFF" is displayed on the multi-information display (Step "H").

HINT:

If the VSC OFF indicator light does not come on and "Traction Control Turned OFF" is not displayed on the multi-information display in step "H", repeat steps "A" to "H".




b.

End of Inspection Mode.

i.

Turning the ignition switch off ends Inspection Mode.

NOTICE:

If the ignition switch is turned to ON within 60 seconds of being turned off, the system will reenter Inspection Mode.



ii.

Confirm that the VSC OFF indicator light turns off and the "Traction Control Turned OFF" on the multi-information display is cleared (Confirm that Inspection Mode is canceled).