The skid control ECU (brake actuator assembly) communicates with the following ECUs and sensors via CAN communication.
ECM
TCM (for CVT)
Airbag sensor assembly
Yaw rate and acceleration sensor (airbag sensor assembly)
Steering sensor
Power steering ECU assembly
Main body ECU (multiplex network body ECU)
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| U007488 | Control Module Communication Bus "B" Off Bus Off | The +BS terminal voltage is between 9.6 and a 16.5 V and a bus OFF state occurs for 0.1 second or more. | CAN communication system | Brake |
| U007688 | Control Module Communication Bus "D" Off Bus Off | The +BS terminal voltage is between 9.6 and a 16.5 V and a bus OFF state occurs for 0.1 second or more. | CAN communication system | Brake |
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the ECM for 2 seconds or more. | ·
CAN communication system ·
ECM ·
Skid control ECU (brake actuator assembly) |
Brake |
| U010187 | Lost Communication with TCM Missing Message | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals cannot be sent to the TCM (ECM) for 2 seconds or more. | ·
CAN communication system ·
TCM (ECM) ·
Skid control ECU (brake actuator assembly) |
Brake |
| U012587 | Lost Communication with Multi-axis Acceleration Sensor Module Missing Message | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the yaw rate and acceleration sensor (airbag sensor assembly) cannot be received for 1 second or more. | ·
CAN communication system ·
Yaw rate and acceleration sensor (airbag sensor assembly) ·
Skid control ECU (brake actuator assembly) |
Brake |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the steering sensor cannot be received for 1 second or more. | ·
CAN communication system ·
Steering sensor ·
Skid control ECU (brake actuator assembly) |
Brake |
| U015187 | Lost Communication with Restraints Control Module Missing Message | The +BS terminal voltage is between 9.6 and 16.5 V, the vehicle speed is 6 km/h (4 mph) or more, and signals from the airbag sensor assembly cannot be received for 5 seconds or more. | ·
CAN communication system ·
Airbag sensor assembly ·
Skid control ECU (brake actuator assembly) |
Brake |
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Operate the GTS to enter the Health Check.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs for related systems are output together with DTC U007488, U010087, U010187, U012587, U012687 or U015187 | A |
| Only U007488, U010087, U010187, U012587, U012687 or U015187 is output | B |
| DTCs are not output | C |
A
B
C
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING