Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  TERMINALS OF ECU  


TERMINALS OF ECU (BRAKE ACTUATOR ASSEMBLY)


C439616C01
0.198,0.146 0.51,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Skid Control ECU [Brake Actuator Assembly])
- -


Terminal No. (Symbol) Terminal Description
1 (+BM) ABS motor relay power supply
2 (STP) Stop light switch assembly input
3 -
4 (SP1) Speed signal output for speedometer
5 -
6 (IGR) IGR power source input
7 -
8 -
9 -
10 (CANL) CAN communication line 1 (L)
11 (CANH) CAN communication line 1 (H)
12 (STP2) Stop light switch assembly input
13 (GND2) Pump motor ground
14 -
15 -
16 -
17 -
18 (CA2L) CAN communication line 2 (L)
19 (CA2H) CAN communication line 2 (H)
20 (CSW) VSC OFF switch (combination switch assembly) input
21 -
22 -
23 -
24 -
25 (+BS) ABS solenoid relay power supply
26 (FR-) Front wheel speed RH (-) signal input
27 (FR+) Front wheel speed RH (+) signal input
28 (STPO) Stop light switch assembly output
29 (RL+) Rear wheel speed LH (+) signal input
30 (RL-) Rear wheel speed LH (-) signal input
31 -
32 -
33 (RR-) Rear wheel speed RH (-) signal input
34 (RR+) Rear wheel speed RH (+) signal input
35 -
36 (FL+) Front wheel speed LH (+) signal input
37 (FL-) Front wheel speed LH (-) signal input
38 (GND1) Skid control ECU (brake actuator assembly) ground


TERMINAL INSPECTION (BRAKE ACTUATOR ASSEMBLY)


a.

Disconnect the A37 connector and measure the voltage or resistance on the wire harness side.

C439617C02
1.667,1.167 2.104,1.469 0.438,0.302 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.75,1.24 2.208,1.438 0.458,0.198 10 false A37
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control (brake actuator assembly) as the connector is watertight.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A37-1 (+BM) - Body ground ABS motor relay power supply Always 11 to 14 V
A37-2 (STP) - Body ground Stop light switch assembly input Brake pedal depressed → released (Brake pedal depressed → released) 8 to 14 V → Below 1.5 V
A37-6 (IGR) - Body ground IGR power source input Ignition switch ON 11 to 14 V
A37-12 (STP2) - Body ground Stop light switch assembly input Stop light switch assembly on → off (Brake pedal depressed → released) 8 to 14 V → Below 1.5 V
A37-13 (GND2) - Body ground Pump motor ground Always Below 1 Ω
A37-20 (CSW) - Body ground VSC OFF switch (combination switch assembly) input VSC OFF switch (combination switch assembly) on → off (Pressed → not pressed) Below 1 Ω → 10 kΩ or higher
A37-25 (+BS) - Body ground ABS solenoid relay power supply Always 11 to 14 V
A37-28 (STPO) - Body ground Stop light switch assembly output Always 11 to 14 V
A37-38 (GND1) - Body ground Skid control ECU (Brake actuator assembly) ground Always Below 1 Ω



TERMINALS OF ECU (STEERING SENSOR)


C358931C12
4.74,0.854 5.073,1.104 0.333,0.25 4.667,0.177 4.979,0.375 0.313,0.198 10 false *a 4.792,0.917 5.104,1.115 0.313,0.198 10 false H39
*a Component without harness connected
(Steering Sensor)
- -


Terminal No. (Symbol) Terminal Description
1 -
2 (2S) Wiper motor operation signal
3 (CANH) CAN communication line H
4 (BAT) ECU power supply input
5 -
6 (ESS) Body Ground
7 (HEAD) Headlight operation signal
8 (CANL) CAN communication line L
9 (IGR) ECU power supply input
10 -


TERMINAL INSPECTION (STEERING SENSOR)


a.

Disconnect the H39 connector and measure the voltage or resistance on the wire harness side.

C427251C01
3.448,0.292 3.781,0.573 0.333,0.281 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 3.49,0.354 3.948,0.552 0.458,0.198 10 false H39
*a Front view of wire harness connector
(to Steering Sensor)
- -


HINT:

Voltage cannot be measured with the connector connected to the steering sensor as the connector is watertight.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H39-4 (BAT) - Body ground ECU power supply input Always 11 to 14 V
H39-6 (ESS) - Body ground Body ground Always Below 1 Ω
H39-9 (IGR) - Body ground ECU power supply input Ignition switch ON 11 to 14 V