Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR GLASS › 2020.07–2021.11
RM36W0E _59 Vehicle Exterior _088061 MIRROR (EXT) _0421712 OUTER REAR VIEW MIRROR GLASS G

MIRROR (EXT)  OUTER REAR VIEW MIRROR GLASS  INSPECTION  


PROCEDURE

Hide 87961 1.INSPECT MIRROR OUTER LH (for TMC Made)

a.

Check the operation of the mirror heater.

i.
B563094C01
1.646,0.854 2.26,0.438 true 2.021,1.188 2.698,1.188 true 2.323,0.344 2.479,0.573 0.156,0.229 10 false 2 2.76,1.094 2.917,1.323 0.156,0.229 10 false 1 2.427,0.74 2.708,0.938 0.281,0.198 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 6.4 to 9.6 Ω


If the result is not as specified, replace the outer mirror LH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.


i.

Connect 4 new 1.5 V dry-cell batteries in series.


ii.
B563095C01
2.094,0.615 2.406,0.813 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
1 - 6 V battery positive (+)
2 - 6 V battery negative (-)
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror LH.



Hide 87931 2.INSPECT OUTER MIRROR RH (for TMC Made)

a.

Check the operation of the mirror heater.

i.
B563092C01
1.073,0.51 1.813,0.896 true 0.76,1.271 1.438,1.271 true 0.833,0.865 1.146,1.063 0.313,0.198 10 false *a 0.583,1.177 0.896,1.375 0.313,0.198 10 false 1 0.948,0.406 1.26,0.604 0.313,0.198 10 false 2
*a Component without harness connected
(Outer Mirror RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 6.4 to 9.6 Ω


If the result is not as specified, replace the outer mirror RH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 6 V.


i.
B563093C01
0.51,0.74 0.823,0.938 0.313,0.198 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Connect 4 new 1.5 V dry-cell batteries in series.


ii.

Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
1 - 6 V battery positive (+)
2 - 6 V battery negative (-)
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror RH.



Hide 87961 3.INSTALL OUTER MIRROR LH (for TMMF Made)

a.
B539044C01
2,1.479 2.771,1.573 true 1.875,0.958 2.594,0.771 true 0.177,0.146 0.49,0.344 0.313,0.198 10 true *a 2.625,0.677 2.938,0.875 0.313,0.198 10 false 1 2.833,1.479 3.146,1.677 0.313,0.198 10 false 2
*a Component without harness connected
(Outer Mirror LH)


Check the outer mirror heater operation. (w/ Mirror Heater )

i.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 10.5 to 12.8 Ω


If the result is not as specified, replace the outer mirror LH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 4.5 V.


i.

Connect 3 new 1.5 V dry-cell batteries in series.


ii.
B539280C01
0.292,0.333 0.667,0.604 0.375,0.271 10 false *a
*a Component without harness connected
(Outer Mirror LH)


Apply 4.5 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
1 - 4.5 V battery negative (-)
2 - 4.5 V battery positive (+)
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror LH.



Hide 87931 4.INSPECT OUTER MIRROR RH (for TMMF Made)

a.
B535019C01
0.667,1.5 1.438,1.5 true 0.802,0.771 1.563,0.938 true 0.188,0.167 0.5,0.365 0.313,0.198 10 false *a 0.667,0.667 0.979,0.865 0.313,0.198 10 false 1 0.521,1.427 0.833,1.625 0.313,0.198 10 false 2
*a Component without harness connected
(Outer Mirror RH)


Check the outer mirror heater operation. (w/ Mirror Heater)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 25°C 10.5 to 12.8 Ω


If the result is not as specified, replace the outer mirror RH.



b.

Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor System)

NOTICE:

Do not apply a voltage of more than 4.5 V.


i.

Connect 3 new 1.5 V dry-cell batteries in series.


ii.
B539281C01
0.177,0.24 0.552,0.49 0.375,0.25 10 false *a
*a Component without harness connected
(Outer Mirror RH)


Apply 4.5 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on.

OK:
Tester Connection Specified Condition
1 - 4.5 V battery negative (-)
2 - 4.5 V battery positive (+)
Outer rear view mirror indicator comes on


If the result is not as specified, replace the outer mirror RH.