Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY (for Halogen Headlight) › 2020.07–2021.11
RM36W0E _59 Vehicle Exterior _087824 LIGHTING (EXT) _0421009 HEADLIGHT ASSEMBLY(for Halogen Headlight) A

LIGHTING (EXT)  HEADLIGHT ASSEMBLY(for Halogen Headlight)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Halogen Headlight)>PRECAUTION

·

Handle components indoors as much as possible to prevent foreign matter from entering and adhering to headlight assembly components.

·

Do not reuse parts which have reduced fastening ability due to thread damage.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

When installing components, make sure that the wire harness is not pinched or pulled.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 8158AJ 1.REMOVE DAYTIME RUNNING LIGHT LED

a.
E431584C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the daytime running light LED as shown in the illustration.


Hide 81110B 2.REMOVE NO. 1 HEADLIGHT BULB

a.
E431578C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the No. 1 headlight bulb from the headlight assembly as shown in the illustration.

NOTICE:

Do not touch the No. 1 headlight bulb glass with your fingers.



Hide 81135F 3.REMOVE HEADLIGHT BACK COVER

a.
E431579

Remove the headlight back cover.


Hide 81610F 4.REMOVE CLEARANCE LIGHT BULB

a.
E431580C01
0,0 0,0 false
V113147

Disconnect in this Direction


Turn the clearance light socket with the clearance light bulb as shown in the illustration to remove it.


b.
E431581

Remove the clearance light bulb from the clearance light socket.


Hide 81510D 5.REMOVE FRONT TURN SIGNAL LIGHT BULB

a.
E431582C01
0,0 0,0 false
V113147

Remove in this Direction


Turn the front turn signal light socket with the front turn signal light bulb as shown in the illustration to remove it.


b.
E431583

Remove the front turn signal light bulb from the front turn signal light socket.


Hide 85662 6.REMOVE HEADLIGHT LEVELING MOTOR (for TMC Made)

a.
E431585

Turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit.

HINT:

Make sure to remember the number of aiming screw rotations.



b.
E431586C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the headlight leveling motor as shown in the illustration.


Hide 85662 7.REMOVE HEADLIGHT LEVELING MOTOR (for TMMF Made)

a.
E450095

Turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit.

HINT:

Make sure to remember the number of aiming screw rotations.



b.
E450096C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the headlight leveling motor as shown in the illustration.


Hide 85669 8.REMOVE HEADLIGHT LEVELING MOTOR BASE PACKING

a.
E431589

Remove the headlight leveling motor base packing.

NOTICE:

The headlight leveling motor base packing must not be reused.



Hide 8110B 9.REMOVE HEADLIGHT LENS SUB-ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight lens.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the back of the headlight lens, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E431593

Remove the 9 screws.


b.
E431595

Using a dryer, heat the backside of the headlight assembly.

NOTICE:

If the headlight assembly is heated unevenly, it will deform or melt.



c.
E431597

Disengage the claws to remove the headlight lens sub-assembly.


d.

Remove the headlight lens from the headlight housing sub-assembly.

HINT:

If the headlight lens cannot be removed even after heating, using a screwdriver with its tip wrapped with protective tape, lift the headlight lens. Be careful not to damage the headlight lens and headlight housing sub-assembly.



Hide 81134 10.REMOVE HEADLIGHT GASKET

NOTICE:
·

The headlight lens gasket must not be reused.

·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not touch the inner surface of the lens and metallic surfaces as much as possible, or they may become dirty.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E375115

Remove the headlight lens gasket from the headlight housing sub-assembly.

NOTICE:

Make sure to replace the headlight lens gasket with a new one. Failure to do so may cause water ingress.



Hide 11.REMOVE NO. 2 HEADLIGHT REFLECTOR (for TMC Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No. 2 headlight reflector or other components.

·

Do not touch the No. 2 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the No. 2 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E438672

Remove the 3 screws and No. 2 headlight reflector.


Hide 12.REMOVE NO. 2 HEADLIGHT REFLECTOR (for TMMF Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No. 2 headlight reflector or other components.

·

Do not touch the No. 2 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the No. 2 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E444070

Disengage the claws to remove the No. 2 headlight reflector.


Hide 13.REMOVE NO. 1 HEADLIGHT REFLECTOR (for TMC Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No.1 headlight reflector or other components.

·

D(o not touch the No.1 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matte on the No. 1 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E438671

Remove the screw.


b.

Disengage the claw to remove the No. 1 headlight reflector.


Hide 14.REMOVE NO. 1 HEADLIGHT REFLECTOR (for TMMF Made)

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the No.1 headlight reflector or other components.

·

D(o not touch the No.1 headlight reflector with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matte on the No. 1 headlight reflector or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



a.
E444069

Remove the 2 screws.


b.

Disengage the claw to remove the No. 1 headlight reflector.


Hide 81175 15.REMOVE HEADLIGHT UNIT ASSEMBLY

NOTICE:
·

Make sure to wear clean rubber gloves when performing this procedure.

·

Do not allow dirt or foreign matter to get on the headlight unit assembly or other components.

·

Prevention of static electricity is required during this procedure.

·

Use static electricity countermeasures SST (desktop anti-static mat set) and observe all precautions to prevent damage to the system by electrostatic discharge (ESD).

·

Do not touch the headlight unit assembly with bare hands.

·

Do not allow metallic surfaces to become dirty, as such surfaces become damaged even if they are only lightly wiped with a soft cloth.

·

If there are any fingerprints or foreign matter on the headlight unit assembly or other components, wipe them off with a soft cloth.

·

Do not use solvent to clean components. Only clean them with a dry cloth.



SST
09890-47010  (09891-04010, 09891-04020, 09891-04030, 09891-04040)

a.
E438673

Disengage the claws.


b.
E438674

Disengage the clamp and claws.


c.
E438675

While holding the headlight unit assembly by hand, turn the aiming screw as shown in the illustration until the aiming screw are disconnected from the headlight unit assembly.

HINT:

Make sure to remember the number of aiming screw rotations.



d.
E438676C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the headlight unit assembly from the headlight housing sub-assembly.


e.

When installing a new headlight unit assembly:

i.
E450097

Disengage clamp to remove the pivot collar.