Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › 2020.07–2021.04
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM U

1KR-FE ENGINE CONTROL  SFI SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in neutral, the A/C switch should be off and all accessory switches should be off.


a.

Warm up the engine.


b.

Turn the A/C switch off.


c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Data List.

HINT:
·

To display the list box, press the pull down menu button next to Primary. Then select a measurement group.

·

When you select a measurement group, the ECU data belonging to that group is displayed.

·

Measurement Group List / Description

-

All Data / All data

-

Primary / -

-

Engine Control / Engine control system related data

-

Ptrl General / -

-

Ptrl AF Control / Air fuel ratio control system related data

-

Ptrl AF O2 Sensor / Air fuel ratio sensors related data

-

Ptrl Throttle / Gasoline throttle system related data

-

Ptrl Intake Control / Intake control system related data

-

Ptrl Valve Control / Valve control system related data

-

Ptrl Misfire / "Misfire" related data

-

Ptrl Starting / "Difficult to start" related data

-

Ptrl Rough Idle / "Rough idle" related data

-

Ptrl Evaporative / Evaporative system related data

-

Ptrl CAT Converter / Catalyst converter related data

-

Check Mode / Check mode related data

-

Monitor Status / Monitor status related data

-

Ignition / Ignition system related data

-

Charging Control / Charging control system related data

-

Compression / Data used during "Check the Cylinder Compression" Active Test

-

Vehicle Information / Vehicle information





h.

According to the display on the GTS, read the Data List.

HINT:

The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all of the Data List items listed for that group will be displayed.




Various Vehicle Conditions 1 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Total distance traveled Min.: 0 [km], Max.: 1677215 [km] - -
Total Distance Traveled - Unit Total Distance Traveled unit km or mile - -
Vehicle Speed Vehicle speed Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Actual vehicle speed
·

This is the current vehicle speed.

·

The vehicle speed is detected using the wheel speed sensors.

-

There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the Freeze Frame Data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.



Engine Speed Engine speed Min.: 0 rpm, Max.: 16383 rpm 790 to 940 rpm: Idling (shift lever in neutral, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
Calculate Load Load calculated by ECM Min.: 0%, Max.: 100% 11 to 25%: Idling
15 to 25%: Running without load at 2500 rpm
·

This is the engine load calculated based on the actual intake manifold pressure.

·

Calculate Load = Actual intake manifold pressure / maximum intake manifold pressure x 100 (%)

(For example, when the estimated intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.)


Vehicle Load Vehicle load Min.: 0%, Max.: 25700% - This is the engine intake air charging efficiency.
Atmospheric Pressure Atmospheric pressure Min.: 0 kPa (0 psi), Max.: 255 kPa (36.98 psi) Equivalent to atmospheric pressure (absolute pressure)
·

This value is calculated based on the atmospheric pressure sensor.

·

Standard atmospheric pressure: 101 kPa(abs) [758 mmHg(abs)]

·

For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). This varies by weather.


Intake Manifold Absolute Pressure Intake manifold absolute pressure Min.: 0 kPa (0 psi), Max.: 2047.96 kPa (296.95 psi)
·

80 to 110 kPa (600 to 825 mmHg(abs)): Ignition switch ON

·

29 to 37 kPa (218 to 278 mmHg(abs)): Idling with warmed up engine


·

This is the intake manifold pressure.

·

This item is the pressure detected by the manifold absolute pressure sensor.


HINT:

When the ignition switch is ON, the manifold absolute pressure and atmospheric pressure are approximately the same (standard atmospheric pressure = 101 kPa(abs) [758 mmHg(abs)]).


Intake Manifold Absolute Pressure Supported Status of Intake Manifold Absolute Pressure Unsupp or Supp Supp -
Coolant Temperature Engine coolant temperature Min.: -40°C (-40°F), Max.: 215°C (419°F) 75 to 100°C (167 to 212°F): After warming up This is the engine coolant temperature.
HINT:
·

After warming up the engine, the engine coolant temperature will be 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.



Intake Air Temperature Intake air temperature Min.: -40°C (-40°F), Max.: 140°C (284°F) Equivalent to temperature at location of intake air temperature sensor (manifold absolute pressure sensor) This is the intake air temperature.
HINT:
·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.

·

If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.



Ambient Temperature Ambient temperature Min.: -40°C (-40°F), Max.: 215°C (419°F) Actual ambient temperature This is the ambient temperature.
HINT:

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature will be approximately equal.


Engine Run Time Engine run time Min.: 0 sec, Max.: 65535 sec Time after engine start This is the time elapsed since the engine was started.
HINT:

The time is counted only while the engine is running.


IG-ON Coolant Temperature Engine coolant temperature when the ignition switch is turned to ON Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) - This is the engine coolant temperature stored when the ignition switch is turned to ON.
Initial Engine Coolant Temperature Engine coolant temperature when the engine is started Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) - This is the engine coolant temperature stored when the engine is started.
IG-ON Intake Air Temperature Intake air temperature when the ignition switch is turned to ON Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) - This is the intake air temperature stored when the ignition switch is turned to ON.
Initial Engine Intake Air Temperature Intake air temperature when the engine is started Min.: -40°C (-40°F), Max.: 119.3°C (246.7°F) - This is the intake air temperature stored when the engine is started.
Battery Voltage Battery voltage Min.: 0 V, Max.: 65.5 V 11 to 14 V: Ignition switch ON If 11 V or less, characteristics of some electrical components may change.
Battery Sensor Voltage Battery sensor voltage Min.: 0 V, Max.: 79.998 V 11 to 14 V (Idling) -
BATT Voltage Battery voltage Min.: 0 V, Max.: 79.998 V 11 to 14 V: Ignition switch ON If 11 V or less, characteristics of some electrical components may change.
IGR Status of IGR terminal ON or OFF IG ON: ON -

Throttle Control (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Accelerator Position Accelerator pedal position Min.: 0%, Max.: 399.9% Actual accelerator pedal position This is the accelerator pedal position defined using the learned fully released position (sensor output) of No. 1 accelerator pedal position sensor as 0% and the fully depressed position as 100%.
Accelerator Position Sensor No.1 Voltage % Absolute No. 1 accelerator pedal position Min.: 0%, Max.: 100%
·

10 to 25%: Accelerator pedal fully released

·

50 to 100%: Accelerator pedal fully depressed


The No. 1 accelerator pedal position sensor output is converted using 5 V = 100%.
HINT:

If there are no accelerator pedal position sensor DTCs stored, it is possible to conclude that the accelerator pedal position sensor system is normal.


Accelerator Position Sensor No.2 Voltage % Absolute No. 2 accelerator pedal position Min.: 0%, Max.: 100%
·

20 to 45%: Accelerator pedal fully released

·

68 to 100%: Accelerator pedal fully depressed


The No. 2 accelerator pedal position sensor output is converted using 5 V = 100%.
Accelerator Position Sensor No.1 Voltage No. 1 accelerator pedal position sensor voltage Min.: 0 V, Max.: 4.98 V
·

0.7 to 1.2 V: Accelerator pedal fully released

·

2.8 to 4.6 V: Accelerator pedal fully depressed


This is the voltage output from the No. 1 accelerator pedal position sensor.
Accelerator Position Sensor No.2 Voltage No. 2 accelerator pedal position sensor voltage Min.: 0 V, Max.: 4.98 V
·

1.2 to 2.0 V: Accelerator pedal fully released

·

3.6 to 4.6 V: Accelerator pedal fully depressed


This is the voltage output from the No. 2 accelerator pedal position sensor.
Accelerator Idle Position Whether or not accelerator pedal position sensor detecting released accelerator pedal ON or OFF ON: Accelerator pedal fully released This is a parameter calculated by the ECM which indicates whether the accelerator pedal is in the learned idle position.
Throttle Position Sensor No.1 Voltage % Absolute No. 1 throttle position sensor Min.: 0%, Max.: 100%
·

4 to 22%: Accelerator pedal fully released

·

75 to 95%: Accelerator pedal fully depressed (engine running)


The No. 1 throttle position sensor output is converted using 5 V = 100%.
HINT:

If there are no throttle position sensor DTCs stored, it is possible to conclude that the throttle position sensor system is normal.


Throttle Position Sensor No.2 Voltage % Absolute No. 2 throttle position sensor Min.: 0%, Max.: 100%
·

4 to 22%: Accelerator pedal fully released

·

75 to 95%: Accelerator pedal fully depressed (engine running)


The No. 2 throttle position sensor output is converted using 5 V = 100%.
Throttle Sensor Position Throttle sensor position Min.: 0%, Max.: 100%
·

4 to 30%: Accelerator pedal fully released

·

64 to 96%: Accelerator pedal fully depressed


·

This is the throttle valve opening amount used for engine control.

·

This value has no meaning when the ignition switch is ON and the engine is stopped.


Throttle Position Sensor No.1 Voltage No. 1 throttle position sensor output voltage Min.: 0 V, Max.: 4.98 V
·

0.6 to 1.1 V: Accelerator pedal fully released

·

4.2 to 4.54 V: Accelerator pedal fully depressed


This is the No. 1 throttle position sensor output voltage.
Throttle Position Sensor No.2 Voltage No. 2 throttle position sensor output voltage Min.: 0 V, Max.: 4.98 V
·

3.9 to 4.4 V: Accelerator pedal fully released

·

0.46 to 0.76 V: Accelerator pedal fully depressed


This is the No. 2 throttle position sensor output voltage.
Throttle Position Command Throttle position command value Min.: 0 V, Max.: 4.98 V 0.5 to 4.8 V The value displayed for this item is the same as Throttle Request Position.
Throttle Position Sensor Open Position No.1 No. 1 throttle position sensor Min.: 0 V, Max.: 4.98 V 0.6 to 1.4 V This is the No. 1 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released, the throttle valve is kept open by the throttle valve opener when the ignition switch is ON.
Throttle Position Sensor Open Position No.2 No. 2 throttle position sensor Min.: 0 V, Max.: 4.98 V 1.7 to 2.5 V This is the No. 2 throttle position sensor output voltage when there is no current supplied to the electronic throttle actuator. If the accelerator pedal is released, the throttle valve is kept open by the throttle valve opener when the ignition switch is ON.
Throttle Motor Current Throttle actuator current Min.: 0 A, Max.: 19.9 A 0 to 3.0 A: Idling with warmed up engine (A/C off and shift lever in neutral) When the value of this item is large but the actual opening angle (Throttle Position Sensor No.1 Voltage) does not reach the target opening angle (Throttle Request Position), there is an "unable to open" malfunction.
Throttle Motor Duty Ratio Throttle actuator Min.: 0%, Max.: 100% 0 to 22%: Idling with warmed up engine (A/C off and shift lever in neutral) This is the output duty ratio of the throttle actuator drive circuit.
Throttle Motor Duty Ratio (Open) Throttle actuator duty ratio (open) Min.: 0%, Max.: 255% 0 to 40%: Idling with warmed up engine (A/C off and shift lever in neutral) This is the duty ratio used to drive the throttle actuator and open the throttle valve. It is an ECM command signal.
Throttle Motor Duty Ratio (Close) Throttle actuator duty ratio (close) Min.: 0%, Max.: 255% 0 to 40%: Idling with warmed up engine (A/C off and shift lever in neutral) This is the duty ratio used to drive the throttle actuator and close the throttle valve. It is an ECM command signal.
HINT:

During idle, the throttle valve opening angle is usually controlled using a duty ratio drive signal which closes the throttle valve. However, if carbon deposits have built up, it may be necessary to open the throttle valve more than the throttle valve opener does. In that case, the opening angle is controlled using the "Throttle Motor Duty Ratio (Open)" signal.


Throttle Position Sensor Fully Closed Learn Value Throttle valve fully closed position (learned value) Min.: 0 V, Max.: 4.98 V 0.6 to 0.9 V: Accelerator pedal fully released The ECM uses this learned value to determine the fully closed (and fully open) position of the throttle valve. This learned value is calculated by the ECM with the throttle valve opener angle.
+BM Voltage +BM voltage Min.: 0 V, Max.: 79.998 V 11 to 14 V: Ignition switch ON -
Actuator Power Supply Actuator power supply ON or OFF - -
Throttle Position Throttle valve opening angle Min.: 0 deg, Max.: 499.99 deg - This value has no meaning when the ignition switch is ON and the engine is stopped.

Fuel System (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Injector Cylinder #1 (Port) Injection period of the No. 1 cylinder Min.: 0 μs, Max.: 65535 μs 1300 to 3100 μs: Idling with warmed up engine (A/C off and shift lever in neutral) This is the injection period of the No. 1 cylinder (the command value from the ECM).
Injection Volume Cylinder #1 Injection volume (cylinder 1) Min.: 0 ml, Max.: 2 ml - This is the fuel injection volume for 10 injections.
Injection Volume Injection volume Min.: -25%, Max.: 24.8% - -
Engine Fuel Rate Engine fuel rate Min.: 0 L/h, Max.: 3276.75 L/h - -
Engine Fuel Rate Engine fuel rate Min.: 0 gm/sec, Max.: 1310.7 gm/sec - -
Vehicle Fuel Rate Vehicle fuel rate Min.: 0 gm/sec, Max.: 1310.7 gm/sec - -
Fuel Pump/Speed Status Fuel pump status ON or OFF ON: Fuel pump on -
Current Fuel Type Current fuel type - Gasoline/petrol -

EVAP System (Ptrl Evaporative)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EVAP (Purge) VSV Purge VSV control duty Min.: 0%, Max.: 100% 0 to 10%: Idling
·

This is the command signal from the ECM.

·

This is the purge VSV control duty ratio. When EVAP (Purge) VSV is any value except 0%, EVAP purge* is being performed.

*: Gasoline vapor from the fuel tank is being introduced into the intake system via the purge VSV.

·

When the engine is cold or immediately after the engine is started, EVAP (Purge) VSV will be 0%.


EVAP Purge VSV VSV status for EVAP control ON or OFF - This item is ON when EVAP (Purge) VSV is approximately 30% or higher, and is OFF when the VSV duty ratio is less than 30%.
Purge Cut VSV Duty Purge VSV duty Min.: 0%, Max.: 399.9% - -

Air Fuel Ratio Control 1 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target Air-Fuel Ratio Target air fuel ratio Min.: 0, Max.: 2 0.8 to 1.2: During idling
·

This is the target air fuel ratio used by the ECM.

·

1.0 is the stoichiometric air fuel ratio. Values that are more than 1.0 indicate the system attempting to make the air fuel ratio leaner. Values that are less than 1.0 indicate the system attempting to make the air fuel ratio richer.



Air Fuel Ratio Control 2 (Ptrl AF O2 Sensor)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
O2 Sensor Voltage B1S1 Heated oxygen sensor output voltage for bank 1 sensor 1 Min.: 0 V, Max.: 1.275 V 0 to 1.0 V
·

This is the output voltage of the heated oxygen sensor (sensor 1).

·

Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio.

·

Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio.

·

During air fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V.

·

Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor.


O2 Sensor Voltage B1S2 Heated oxygen sensor output voltage for bank 1 sensor 2 Min.: 0 V, Max.: 1.275 V 0 to 1.0 V
·

This is the output voltage of the heated oxygen sensor (sensor 2).

·

Values close to 0 V indicate an air fuel ratio leaner than the stoichiometric ratio.

·

Values close to 1 V indicate an air fuel ratio richer than the stoichiometric ratio.

·

During air fuel ratio feedback control, the value moves back and forth in the range of 0 to 1 V.

·

Performing the "Control the Injection Volume" or "Control the Injection Volume for A/F Sensor" function of the Active Test enables the technician to check voltage output of the sensor.


O2 Sensor Impedance B1S2 Heated oxygen sensor impedance Min.: 0 ohm, Max.: 21247.67 ohm - -
A/F (O2) Sensor Heater B1S1 Heated oxygen sensor heater for bank 1 sensor 1 ON or OFF - -
O2 Sensor Heater B1S2 Heated oxygen sensor heater for bank 1 sensor 2 ON or OFF - -
O2 Sensor Heater Current Value B1S2 Heated oxygen sensor heater current for bank 1 sensor 2 Min.: 0 A, Max.: 65.535 A - -
Short FT B1S1 Short-term fuel trim Min.: -100%, Max.: 99.21% -25 to 25% This item is the "short-term fuel injection volume compensation ratio" used to maintain the air fuel ratio at the stoichiometric ratio using the heated oxygen sensor for feedback.
Long FT B1S1 Long-term fuel trim Min.: -100%, Max.: 99.21% -25 to 25%
·

The ECM will learn the Long FT B1S1 values based on Short FT B1S1. The goal is to keep Short FT B1S1 at 0% to keep the air fuel ratio mixture at the stoichiometric ratio.

·

This value is used to determine whether the system related to air fuel ratio control is malfunctioning.

·

The condition of the system is determined based on the sum of Short FT B1S1 and Long FT B1S1 (excluding times when the system is in transition).

-

25% or higher: There may be a lean air fuel ratio.

-

-25 to 25%: The air fuel ratio can be determined to be normal.

-

-25% or less: There may be a rich air fuel ratio.



Fuel System Status Bank 1 Fuel system status (bank 1) Unused, OL, CL, OLDrive, OLFault or CLFault CL: Idling after warming up
·

OL (Open Loop): Has not yet satisfied conditions to go to closed loop.

·

CL (Closed Loop): Uses feedback to perform fuel control.

·

OLDrive: Open loop due to driving conditions (fuel enrichment).

·

OLFault: Open loop due to a detected system fault.

·

CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.



Ignition System (Ignition)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ignition Timing Cylinder #1 Ignition timing advance for No. 1 cylinder Min.: -64 deg, Max.: 63.5 deg 0 to 20 deg: Idling (Neutral position)
30 deg: Running without load at 3000 rpm
-

EGR Control (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target EGR Position EGR valve target opening amount Min.: 0%, Max.: 100% 0%: Idling When the engine is cold or idling, at engine start, etc., the value is 0%.
·

When the valve is fully closed, the value is 0%.

·

When the valve is fully open, the value is 100%.


EGR Step Position EGR step position Min.: 0 step, Max.: 255 step Changes according to engine speed and load This is the ECM control command.
·

When the valve is fully closed, the value is 0 step.

·

When the valve is fully open, the value is 110 step.



VVT Control (Gas Valve Control)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
VVT Advance Fail VVT control failure status ON or OFF OFF ON: There is an intake VVT timing advance malfunction.
Intake VVT Change Angle Bank 1 Intake VVT displacement angle Min.: 0 DegFR, Max.: 639.9 DegFR -
·

This is the intake VVT displacement angle.

·

By checking VVT Change Angle during the Active Test, it is also possible to determine whether or not the camshaft position sensor signal is being output.


Intake VVT OCV Control Duty Ratio Bank 1 Camshaft timing oil control valve assembly operation duty ratio Min.: 0%, Max.: 399.9% - -
Exhaust VVT Hold Learn Value Bank 1 Exhaust VVT hold correct learned value Min.: 0%, Max.: 399.9% - -
Exhaust VVT Change Angle Bank 1 Exhaust VVT displacement angle Min.: 0 DegFR, Max.: 639.9 DegFR - This is the exhaust VVT displacement angle.
Exhaust VVT OCV Control Duty Ratio Bank 1 Camshaft timing oil control valve assembly operation duty ratio Min.: 0%, Max.: 399.9% - -
Intake VVT Target Angle Bank 1 Intake VVT target angle Min.: 0 DegFR, Max.: 639.9 DegFR - -
Exhaust VVT Target Angle Bank 1 Exhaust VVT target angle Min.: 0 DegFR, Max.: 639.9 DegFR - -

Catalyst (Ptrl CAT Converter)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Catalyst Temperature B1S1 Front catalyst temperature Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) -
·

This is the temperature of the front catalyst estimated by the ECM.

·

This item is included in the conditions used to detect catalyst deterioration (DTC P042000), etc., and should therefore be used as a reference when recreating malfunction conditions.


Catalyst Temperature B1S2 Rear catalyst temperature Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) - This is the temperature of the rear catalyst estimated by the ECM.

GPF [Gasoline Particulate Filter] (Ptrl CAT Converter)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Rear Catalyst Estimate Temperature Rear catalyst estimate temperature Min.: -40°C (-40°F), Max.: 6513.5°C (11756.3°F) - This is the temperature of the rear catalyst estimated by the ECM.
Particulate Filter Differential Pressure Bank 1 GPF differential pressure Min.: -327.68 kPa (-47.51 psi), Max.: 327.67 kPa (47.51 psi) 0 to 95 kPa (0 to 13.78 psi) -
Particulate Filter Differential Pressure Bank 1 Supported Status of Particulate Filter Differential Pressure Bank1 supported Unsupp or Supp Supp -
Differential Pressure Sensor Learning Value Bank 1 Differential pressure sensor learning value Bank 1 Min.: -327.68 kPa (-47.51 psi), Max.: 327.67 kPa (47.51 psi) -2.25 to 2.25 kPa (-0.33 to 0.33 psi) This is the deviation from the sensor output zero point when the pressure inside the exhaust pipe becomes the same as the atmospheric pressure while the ignition switch is off.
GPF Differential Pressure Offset Bank1 Corrected value of differential pressure sensor Min.: -327.68 kPa (-47.51 psi), Max.: 327.67 kPa (47.51 psi) 0 to 97.25 kPa (0 to 14.1 psi)
·

This is the value of the differential pressure sensor that is corrected for the zero point deviation.

·

This is used for judging GPF clogging, etc.


GPF Clogged Determination Threshold Bank1 GPF clogging judgment threshold Min.: -327.68 kPa (-47.51 psi), Max.: 327.67 kPa (47.51 psi) 105 kPa (15.2 psi) When the average value of differential pressure sensor exceeds GPF Clogged Determination Threshold, the GPF is judged to be clogged.
GPF Steady Differential Pressure Average Bank1 Differential pressure sensor average value during constant speed driving Min.: -327.68 kPa (-47.51 psi), Max.: 327.67 kPa (47.51 psi) 0 to 100 kPa (0 to 14.5 psi) This is the maximum value of the differential pressure sensor while the driving conditions are stable.
GPF Steady Air Flow Average Bank1 Intake air flow average value during constant speed driving Min.: 0 gm/sec, Max.: 655.35 gm/sec 0 to 58 gm/sec This is the average value of the intake air flow while the driving conditions are stable.
PM Deposition Ratio Bank1 PM deposition ratio Min.: 0%, Max.: 255% 0 to 147% Outputs the deposition ratio of PM accumulated in the GPF.
PM Deposition Value Bank1 PM volume accumulated in GPF Min.: 0 g, Max.: 655.35 g 0 to 33 g Outputs the volume of PM accumulated in the GPF (the value is model's value, from the differential pressure sensor).
PM Deposition Value Bank1 (Modelled/Simulation Value) PM volume accumulated in GPF (Model's value) Min.: 0 g, Max.: 655.35 g 0 to 33 g Outputs the volume of PM accumulated in the GPF (the value is model's value, not sensor's value).
Ash Deposition Ratio Bank1 Ash deposition ratio Min.: 0%, Max.: 255% - Ash is not used in GPF (the value is model's value, not sensor's value).

Various Vehicle Conditions 3 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter signal ON or OFF ON: Starter operating -
Neutral Position SW Park/Neutral position switch status ON or OFF ON: Clutch pedal depressed -
Shift SW Status (Neutral) Neutral position switch assembly status ON or OFF ON: Shift lever in neutral
OFF: Shift lever in any position other than neutral
-
Shift SW Status (Neutral) Supported Neutral position switch assembly status supported Supp or Unsupp Supp -
Neutral Position Switch Neutral position switch status ON or OFF ON: Shift lever in neutral -
Neutral Position Switch Output Voltage Neutral position switch output voltage Min.: 0 V, Max.: 4.99 V 0.7 to 4.3 V -
Clutch SW Clutch switch status ON or OFF ON: Clutch pedal depressed -
Stop Light SW Stop light switch status ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
Immobiliser Communication Immobiliser communication ON or OFF ON: Normal -
ASL SW Speed limiter switch signal ON or OFF
·

ON: Speed limiter switch on

·

OFF: speed limiter switch off


-
Cruise Main SW Cruise control switch status ON or OFF - -
Closed Throttle Position SW Closed throttle position switch status ON or OFF
·

ON: Idling

·

OFF: Accelerator pedal depressed (engine running)


-

Check Mode (Check Mode)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Misfire Test Result Check mode result for misfire monitor Compl or Incmpl - -
A/F (O2) Sensor B1S2 Test Results Check mode result for heated oxygen sensor (sensor 2) Compl or Incmpl - -
A/F (O2) Sensor B1S1 Test Results Check mode result for heated oxygen sensor (sensor 1) Compl or Incmpl - -

Test Result (Monitor Status)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Complete Parts Monitor Comprehensive component monitor Not Avl or Avail -
·

*


Complete Parts Monitor Result Comprehensive component monitor Compl or Incmpl -
·

*


Ignition Monitor Ignition monitor Spark Ignition or Compression Ignition Spark Ignition -
Fuel System Monitor Fuel system monitor Not Avl or Avail -
·

*


Fuel System Monitor Result Fuel system monitor Compl or Incmpl -
·

*


Misfire Monitor Misfire monitor Not Avl or Avail -
·

*


Misfire Monitor Result Misfire monitor Compl or Incmpl -
·

*


EGR/VVT Monitor EGR/VVT monitor Not Avl or Avail -
·

*


EGR/VVT Monitor Result EGR/VVT monitor Compl or Incmpl -
·

*


A/F (O2) Sensor Heater Monitor A/F (O2) sensor heater monitor Not Avl or Avail -
·

*


A/F (O2) Sensor Heater Monitor Result A/F (O2) sensor heater monitor Compl or Incmpl -
·

*


A/F (O2) Sensor Monitor A/F (O2) sensor monitor Not Avl or Avail -
·

*


A/F (O2) Sensor Monitor Result A/F (O2) sensor monitor Compl or Incmpl -
·

*


Secondary Air Injection System Monitor Secondary air injection system monitor Not Avl or Avail -
·

*


Secondary Air Injection System Monitor Result Secondary air injection system monitor Compl or Incmpl -
·

*


EVAP Monitor EVAP monitor Not Avl or Avail -
·

*


EVAP Monitor Result EVAP monitor Compl or Incmpl -
·

*


Heated Catalyst Monitor Heated catalyst monitor Not Avl or Avail -
·

*


Heated Catalyst Monitor Result Heated catalyst monitor Compl or Incmpl -
·

*


Catalyst Monitor Catalyst monitor Not Avl or Avail -
·

*


Catalyst Monitor Result Catalyst monitor Compl or Incmpl -
·

*


*:

Avail: The monitor is available on this vehicle.

Not Avl: The monitor is not available on this vehicle.

Incmpl / Compl: The item changes from Incmpl to Compl if the monitor was completed at least once at some time in the past. This item does not change when the ignition switch is turned off. However, the item changes back to Incmpl when DTCs are cleared or cable is disconnected from the negative (-) battery terminal.


Various Vehicle Conditions 4 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TC Terminal TC terminal status ON or OFF - -
MIL MIL status ON or OFF OFF -
MIL ON Run Distance Distance driven with MIL on Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) - This is the distance driven since the MIL was illuminated.
Running Time from MIL ON Running time from MIL on Min.: 0 min, Max.: 65535 min Running time after MIL turned on -
Time after DTC Cleared Time after DTCs cleared Min.: 0 min, Max.: 65535 min Time after DTCs cleared This is the time elapsed after DTCs were cleared (or after the vehicle left the factory). Time elapsed after the ignition switch is turned off is not counted.
Distance from DTC Cleared Distance driven after DTCs cleared Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) Distance driven after DTCs cleared This is the distance driven since DTCs were cleared (or since the vehicle left the factory).
Warmup Cycle Cleared DTC Warmup cycles after DTCs cleared Min.: 0, Max.: 255 - This is the number of warmup cycles after the DTCs were cleared.
OBD Requirements OBD requirement - EOBD (Euro OBD) -
Number of Emission DTC Emissions-related DTCs Min.: 0, Max.: 127 - This is the number of emissions-related DTCs stored.

Misfire (Gas Misfire)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Misfire Count Cylinder #1 Misfire count of No. 1 cylinder Min.: 0, Max.: 255 0
·

This is the misfire count for No. 1 cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


Misfire Count Cylinder #2 Misfire count of No. 2 cylinder Min.: 0, Max.: 255 0
·

This is the misfire count for No. 2 cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


Misfire Count Cylinder #3 Misfire count of No. 3 cylinder Min.: 0, Max.: 255 0
·

This is the misfire count for No. 3 cylinder.

·

This counter is increased by one for each misfire and is cleared every 200 revolutions.

·

Check this item to help determine the malfunctioning cylinder.


All Cylinders Misfire Count Misfire count of all cylinders Min.: 0, Max.: 255 0
·

This is the total misfire count of all cylinders.

·

This counter is increased by one for each misfire, has a maximum value of 255 and is cleared every 1000 revolutions.



Various Vehicle Conditions 5 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed (Starter Off) Engine speed when starter off Min.: 0 rpm, Max.: 51199 rpm - This is the engine speed immediately after the engine is started.
Starter Count Number of times starter turned on after ignition switch turned to ON Min.: 0, Max.: 255 - This is the number of times the starter turned on during the current trip.
Run Distance of Previous Trip Distance driven during previous trip Min.: 0 km (0 mile), Max.: 655.35 km (407.23 mile) - -
Engine Starting Time Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm) Min.: 0 ms, Max.: 655350 ms -
·

This is the time elapsed from when the starter turns on until the engine speed reaches 400 rpm.

·

This value is cleared 5 seconds after the engine is started and 0 ms will be displayed.


Engine Start Hesitation History of hesitation during engine start ON or OFF - This item changes to ON when the engine speed does not reach 500 rpm during cranking.
Low Revolution for Engine Start History of low engine speed after engine start ON or OFF - This item changes to ON when the engine speed drops to 200 rpm or less within approximately 2 seconds of starting the engine.
Previous Trip Coolant Temp Engine coolant temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) -
·

Before 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature at the end of the previous trip.

·

After 120 seconds elapse after starting the engine, this parameter indicates the engine coolant temperature during the current trip.


Previous Trip Intake Temp Intake air temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) -
·

Before 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature at the end of the previous trip.

·

After 120 seconds elapse after starting the engine, this parameter indicates the intake air temperature during the current trip.


Engine Oil Temperature Estimated engine oil temperature Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
Previous Trip Eng Oil Temp Engine oil temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
Ambient Temp for A/C Ambient temperature for A/C Min.: -40°C (-40°F), Max.: 215°C (419°F) - -
Previous Trip Ambient Temp Ambient temperature during previous trip Min.: -40°C (-40°F), Max.: 215°C (419°F) - -

Various Vehicle Conditions 6 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Alternator Output Duty Ratio Alternator output duty ratio Min.: 0%, Max.: 399.9% Among Charging: change according to quantity of Alternator generation -
Status of Alternator Temperature High Status of alternator temperature high ON or OFF ON: Alternator high temperature Status -
Alternator Voltage - Non Active Test Alternator voltage - non active test Min.: 0 V, Max.: 79.998 V After an engine start: change depending on Battery temperature, a running condition -
Voltage of Alternator Voltage of alternator Min.: 0 V, Max.: 79.99 V - -
Engine Cooling Fan Electric cooling fan ON or OFF - -
Brake Override System Brake override system status ON or OFF ON: Brake override system operating -
Immobiliser Fuel Cut Status Status of immobiliser fuel cut ON or OFF OFF -
Immobiliser Fuel Cut History Immobiliser fuel cut history ON or OFF OFF -
Idle Fuel Cut Idle fuel cut condition ON or OFF ON: Fuel cut operating -
TAU Fuel Cut Low load fuel cut condition ON or OFF ON: Fuel cut operating -
Electrical Load Signal No.1 Status of electrical load signal No. 1 ON or OFF ON: Tail switch ON -
Electrical Load Signal No.2 Status of electrical load signal No. 2 ON or OFF ON: Rear defogger switch ON -
Electric Component Actuation Restriction Count Electric component actuation restriction count Min.: 0, Max.: 255 -

Compression (Compression)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Cylinder #1 Engine speed for No. 1 cylinder Min.: 0 rpm, Max.: 51199 rpm -
·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)

·

This is the engine speed of No. 1 cylinder measured during fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Engine Speed Cylinder #2 Engine speed for No. 2 cylinder Min.: 0 rpm, Max.: 51199 rpm -
·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)

·

This is the engine speed of No. 2 cylinder measured during fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Engine Speed Cylinder #3 Engine speed for No. 3 cylinder Min.: 0 rpm, Max.: 51199 rpm -
·

Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)

·

This is the engine speed of No. 3 cylinder measured during fuel-cut with the engine cranking.

·

When there is compression loss, the engine speed of the malfunctioning cylinder increases.


HINT:

When multiple cylinders have compression loss, the engine speeds for multiple cylinders increase and it is not possible to determine which cylinders have compression loss. At this time, it is necessary to actually perform a compression measurement.


Average Engine Speed of All Cylinder Average engine speed for all cylinders Min.: 0 rpm, Max.: 51199 rpm - Values for this item are only displayed when the Active Test "Check the Cylinder Compression" is performed. (51199 rpm is displayed when the Active Test is not being performed.)

Various Vehicle Conditions 7 (All Data)


Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/neutral position switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


-
Down Shift Indication Down shift indication ON or OFF - -
Up Shift Indication Up shift indication ON or OFF - -
Stop and Start System Engine Status Stop and start system engine status IG, Run, Stopreq, Stop, Restart - -
Battery Type Battery Type Specified or Other - -
TRC/VSC OFF Indicator TRC/VSC OFF indicator ON or OFF - -
Kickdown Switch Kick down switch status ON or OFF - -

ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > Engine > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Injection Volume Control the injection volume Between -12.5% and 24.8%
·

All fuel injector assemblies are tested at the same time.

·

Perform the test at 3000 rpm or less.

·

Injection volume can be changed in fine gradations within the control range.

·

Control the Injection Volume enables the checking and graphing of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2) voltage outputs.

·

To conduct the test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

·

During the Active Test, air fuel ratio feedback control and feedback learning are stopped.


Control the Injection Volume for A/F Sensor Change injection volume -12.5%/0%/12.5%
·

All fuel injector assemblies are tested at the same time.

·

Perform the test at 3000 rpm or less.

·

Control the Injection Volume for A/F Sensor enables the checking and graphing of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2) voltage outputs.

·

To conduct the test, enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / Data List / O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

·

During the Active Test, air fuel ratio feedback control and feedback learning are stopped.


Activate the EVAP Purge VSV Activate purge VSV control ON/OFF
·

The purge VSV is opened with approximately 50% duty ratio.


Activate the Circuit Relay Activate fuel pump ON/OFF Perform this test when the following conditions are met:
·

Ignition switch is ON.

·

Engine is stopped.

·

Shift lever in neutral.


Activate the TC Terminal Turn on and off TC and TE1 (CG) connection ON/OFF
·

Confirm that the vehicle is stopped.

·

ON: TC and TE1 (CG) are connected.

·

OFF: TC and TE1 (CG) are disconnected.


Prohibit the Idle Fuel Cut Prohibit idling fuel cut control Start/Stop Perform this test when the following conditions are met:
·

Ignition switch is ON.

·

Shift lever in neutral.


Control the ETCS Open/Close Slow Speed Throttle actuator
·

Close/Open

·

Start/Stop


Open: Throttle valve opens slowly
Perform this test when the following conditions are met:
·

Ignition switch is ON.

·

Engine is stopped.

·

Accelerator pedal is fully depressed (accelerator pedal position: 58 degrees or more).

·

Shift lever in P or neutral.


Control the ETCS Open/Close Fast Speed Throttle actuator
·

Close/Open

·

Start/Stop


Open: Throttle valve opens quickly
Same as above.
Control the Intake VVT OCV Duty Ratio Bank 1 Control camshaft timing oil control valve assembly -100 to 100% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum advance
-100%: Maximum retard
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly (for intake camshaft) is turned on.

·

Engine runs and idles normally when the camshaft timing oil control valve assembly (for intake camshaft) is off.

·

Perform this test when the following conditions are met:

-

Engine is idling.

-

Shift lever in neutral.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the Exhaust VVT OCV Duty Ratio Bank 1 Control camshaft timing oil control valve assembly -100 to 100% (This value added to present camshaft timing oil control valve control duty)
100%: Maximum retard
-100%: Maximum advance
·

Engine stalls or idles roughly when the camshaft timing oil control valve assembly is operated by 100%.

·

Perform this test when the following conditions are met:

-

Engine is idling.

-

Shift lever in neutral.


·

DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.


Control the EGR Step Position Control EGR valve assembly From 0 to 110 step
·

Perform this test when the following conditions are met:

-

Engine is running.

-

Shift lever in neutral.


·

Do not leave the EGR valve open for 10 seconds or more while performing the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 20 steps or more while performing the Active Test.


Control the Voltage of Alternator Control the alternator generation required voltage 12.5 V to 14.8 V Perform this test when vehicle is stopped.
Control the Select Cylinder F/C (with Ignition) Selected cylinder (cylinder #1 to #3) injector fuel cut
·

#1/#2/#3

·

Start/Stop


Perform this test when the following conditions are met:
·

Vehicle is stopped.

·

Engine is idling.

·

Shift lever in neutral.


Control the All Cylinders Fuel Cut Fuel cut for all cylinders Start/Stop Perform this test when the following conditions are met:
·

Vehicle is stopped.

·

Engine is idling.

·

Shift lever in neutral.


Check the Cylinder Compression Check the cylinder compression pressure Start/Stop Fuel injection and ignition stop of all cylinders.
*1
Control the Engine Cooling Fan Control electric cooling fan motor ON/OFF Perform this test when vehicle is stopped.
HINT:

*1:

While performing this Active Test, the fuel injection and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.


7.

Push the snapshot button to turn the snapshot function on.

HINT:

Using the snapshot function, data can be recorded during the Active Test.


8.

While the engine is not running, press the button to change Check the Cylinder Compression to "Start".

HINT:

After performing the above procedure, the Active Test will start. Fuel injection for all cylinders is prohibited and engine speed measurement enters standby mode.


9.

Crank the engine for about 10 seconds.

HINT:

Continue to crank the engine until the values change from the default value (51199 rpm).


10.

Monitor the engine speed (Engine Speed Cylinder #1 to #3) displayed on the GTS.

NOTICE:
·

In order to protect the starter assembly, do not crank the engine continuously for 20 seconds or more.

·

If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to "Start" and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to "Start" and crank the engine.

·

Make sure the battery is fully charged before performing this Active Test.



HINT:

At first, the GTS will display extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, the engine speed measurement of each cylinder will change to the actual engine speed.


11.

Stop cranking the engine, and then change "Check the Cylinder Compression" to "Stop" after the engine stops.

NOTICE:
·

If the Active Test is changed to "Stop" while the engine is being cranked, the engine will start.

·

After performing the Active Test, make sure to check and clear DTCs.



12.

Push the snapshot button to turn the snapshot function off.

13.

Select "Stored Data" on the GTS screen, select the recorded data and display the data as a graph.

HINT:

If the data is not displayed as a graph, the change of the values cannot be observed.


14.

Check the change in engine speed values.

HINT:

As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.