Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.07–2020.09
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0422141 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B15D3  Stereo Component Amplifier Disconnected  


DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication line.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing.
·

Stereo component amplifier assembly power source circuit

·

AVC-LAN circuit between radio and display receiver assembly and stereo component amplifier assembly

·

Stereo component amplifier assembly

·

Radio and display receiver assembly

·

Harness or connector



HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E488815E01
1.094,0.25 4.156,0.563 3.063,0.313 10 false from Eco Run Vehicle Converter Assembly*1 2.354,1.052 5.313,1.302 2.958,0.25 10 false from Auxiliary Battery*2 1.094,1.781 4.521,1.99 3.427,0.208 10 false from Eco Run Vehicle Converter Assembly*1 4.271,1.219 5.26,1.448 0.99,0.229 10 false AMP NO. 1 4.313,2.74 5.302,2.969 0.99,0.229 10 false ECU-ACC 5.448,1.063 6,1.26 0.552,0.198 10 false H136 3.865,3.417 4.375,3.667 0.51,0.25 10 false TX1+ 5.854,3.417 6.365,3.667 0.51,0.25 10 false TX+ 3.885,3.969 4.396,4.219 0.51,0.25 10 false TX1- 2.875,4.333 3.865,4.563 0.99,0.229 10 false H79 2.875,4.5 4.573,4.854 1.698,0.354 10 false Radio and Display Receiver Assembly 0.177,5.615 3.135,5.865 2.958,0.25 10 false *1: w/ Stop and Start System 0.188,5.99 3.146,6.24 2.958,0.25 10 false *2: w/o Stop and Start System 0.677,6.396 3.635,6.646 2.958,0.25 10 false : AVC-LAN Communication Line 5.781,5.906 7.031,6.271 1.25,0.365 10 false Stereo Component Amplifier Assembly 5.865,3.948 6.375,4.198 0.51,0.25 10 false TX- 5.458,2.583 6.01,2.781 0.552,0.198 10 false H137 5.458,3.417 6.01,3.615 0.552,0.198 10 false H137 5.448,3.958 6,4.156 0.552,0.198 10 false H137 5.448,4.688 6,4.885 0.552,0.198 10 false H136 5.438,5.24 5.99,5.438 0.552,0.198 10 false H136 5.854,1.052 6.406,1.25 0.552,0.198 10 false +B 5.854,2.583 6.406,2.781 0.552,0.198 10 false ACC 5.542,0.833 6.094,1.031 0.552,0.198 10 false 1 5.521,2.375 6.073,2.573 0.552,0.198 10 false 12 5.552,3.198 6.104,3.396 0.552,0.198 10 false 8 5.552,3.74 6.104,3.938 0.552,0.198 10 false 7 5.552,4.479 6.104,4.677 0.552,0.198 10 false 3 5.521,5.031 6.073,5.229 0.552,0.198 10 false 18 5.854,4.667 6.406,4.865 0.552,0.198 10 false GND 5.844,5.229 6.396,5.427 0.552,0.198 10 false GND2 4.281,3.271 4.833,3.469 0.552,0.198 10 false 5 4.281,3.823 4.833,4.021 0.552,0.198 10 false 6 2.688,2.573 5.646,2.823 2.958,0.25 10 false from ACC Relay*2 4.25,0.406 5.24,0.635 0.99,0.229 10 false AMP NO. 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>PRECAUTION


PROCEDURE

1.CHECK DTC
a.

If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

Result:
Result Proceed to
DTC B15C3 is not output. A
DTC B15C3 is output. B




A

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

2.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

5.CHECK FOR DTC
3.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

6.CHECK VEHICLE TYPE

B

6.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)

B

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
7.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the H136 and H137 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H136-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H136-1 (+B) - H136-3 (GND) Ignition switch off 11 to 14 V
H137-12 (ACC) - H136-3 (GND) Ignition switch ACC 11 to 14 V


Result:
Proceed to
OK
NG




OK

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Disconnect the H137 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H79-5 (TX1+) - H137-8 (TX+) Always Below 1 Ω
H79-6 (TX1-) - H137-7 (TX-) Always Below 1 Ω
H79-5 (TX1+) - Body ground Always 10 kΩ or higher
H79-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

12.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE)
a.

Disconnect the H136 and H137 stereo component amplifier assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H136-3 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H136-1 (+B) - H136-3 (GND) Ignition switch off 10.5 to 16 V
H137-12 (ACC) - H136-3 (GND) Ignition switch ACC 10.5 to 16 V


Result:
Proceed to
OK
NG




OK

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Disconnect the H137 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H79-5 (TX1+) - H137-8 (TX+) Always Below 1 Ω
H79-6 (TX1-) - H137-7 (TX-) Always Below 1 Ω
H79-5 (TX1+) - Body ground Always 10 kΩ or higher
H79-6 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Replace the stereo component amplifier assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CLEAR DTC
15.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC
a.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)