Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2020.07
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0421643 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69330 1.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

a.
B566016C04
1.583,3.094 1.938,3.271 0.354,0.177 2.021,4.24 2.25,4.51 true 1.448,4.24 1.208,4.51 true 2.177,3.958 2.469,3.958 true 0.958,3.948 1.25,3.948 true 2.302,4.51 2.729,4.667 0.427,0.156 10 false LSSR 1.104,4.51 1.26,4.667 0.156,0.156 10 false E 2.021,2.896 2.344,3.073 0.323,0.177 10 false *b 1.563,2.885 1.969,3.083 0.406,0.198 10 false *c 0.583,3.229 0.833,3.427 0.25,0.198 10 false *a 0.833,3.885 1.115,4.083 0.281,0.198 10 false L 2.542,3.896 2.823,4.094 0.281,0.198 10 false UL 1.667,3.104 1.896,3.25 0.229,0.146 10 false M1
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Check the door lock motor operation.

i.

Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

Specified Condition:
Tester Connection Specified Condition
M1-4 (L) - Auxiliary battery positive (+)
M1-1 (UL) - Auxiliary battery negative (-)
Lock
M1-1 (UL) - Auxiliary battery positive (+)
M1-4 (L) - Auxiliary battery negative (-)
Unlock


If the result is not as specified, replace the rear door lock assembly RH.



b.

Check the operation of the door unlock detection switch. (w/ Smart Entry and Start System)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-6 (LSSR) - M1-9(E) Lock 10 kΩ or higher
M1-6 (LSSR) - M1-9(E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly RH.



Hide 69330 2.INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

a.
B228544C05
1.583,3.083 1.906,3.271 0.323,0.188 2.219,3.844 2.51,3.844 true 1.021,3.844 1.313,3.844 true 1.594,3.781 0.948,3.281 true 1.948,3.781 2.573,3.302 true 2.323,2.625 2.646,2.802 0.323,0.177 10 false *b 1.458,2.625 1.865,2.823 0.406,0.198 10 false *c 0.396,2.927 0.865,3.177 0.469,0.25 10 false *a 0.885,3.76 1.167,3.958 0.281,0.198 10 false L 2.563,3.75 3.021,3.969 0.458,0.219 10 false UNDL 1.656,3.094 1.875,3.271 0.219,0.177 10 false M1 2.625,3.208 2.906,3.406 0.281,0.198 10 false DL 0.708,3.198 1.167,3.417 0.458,0.219 10 false UL
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Check the door lock motor operation.

i.

Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition
M1-4 (L) - Auxiliary battery positive (+)
M1-3 (UL) - Auxiliary battery negative (-)
Lock
M1-3 (UL) - Auxiliary battery positive (+)
M1-4 (L) - Auxiliary battery negative (-)
Unlock
M1-2 (DL) - Auxiliary battery positive (+)
M1-1 (UNDL) - Auxiliary battery negative (-)
Sets
M1-1 (UNDL) - Auxiliary battery positive (+)
M1-2 (DL) - Auxiliary battery negative (-)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double lockingsystem. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double lockingsystem. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock assembly RH.



b.
B228544C08
1.521,3 2.021,3.25 0.5,0.25 0.958,4.125 1.354,4.125 true 2.208,4.115 2.604,4.115 true 2.167,4.448 2.01,4.146 true 1.406,4.438 1.531,4.156 true 0.802,3.115 0.969,3.271 0.167,0.156 10 false *a 2.396,2.656 2.552,2.802 0.156,0.146 10 false *b 1.385,2.656 1.542,2.802 0.156,0.146 10 false *c 1.167,4.458 1.708,4.656 0.542,0.198 10 false LSSR 0.792,4.042 0.979,4.24 0.188,0.198 10 false E 2.646,4.031 3.146,4.219 0.5,0.188 10 false DSSR 2.167,4.469 2.396,4.667 0.229,0.198 10 false E 1.667,3.042 2.167,3.229 0.5,0.188 10 false M1
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M1-9 (LSSR) - M1-10 (E) Lock 10 kΩ or higher
M1-9 (LSSR) - M1-10 (E) Unlock Below 1 Ω
M1-5 (DSSR) - M1-6 (E) Sets 10 kΩ or higher
M1-5 (DSSR) - M1-6 (E) Unsets Below 1 Ω


If the result is not as specified, replace the rear door lock assembly RH.



Hide 69340 3.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

a.
B566018C04
1.594,3.083 1.958,3.271 0.365,0.188 2.021,4.24 2.26,4.51 true 1.448,4.24 1.229,4.51 true 2.177,3.979 2.469,3.979 true 0.99,3.958 1.281,3.958 true 2.26,4.531 3,4.667 0.74,0.135 10 false LSSR 1.135,4.51 1.302,4.667 0.167,0.156 10 false E 1.281,2.896 1.604,3.073 0.323,0.177 10 false *b 1.698,2.885 2.104,3.083 0.406,0.198 10 false *c 0.479,3.219 0.948,3.469 0.469,0.25 10 false *a 0.865,3.896 1.146,4.094 0.281,0.198 10 false L 2.531,3.917 2.813,4.115 0.281,0.198 10 false UL 1.698,3.094 1.896,3.25 0.198,0.156 10 false N1
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Lock
*c Unlock


Check the door lock motor operation.

i.

Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

Specified Condition:
Tester Connection Specified Condition
N1-4 (L) - Auxiliary battery positive (+)
N1-1 (UL) - Auxiliary battery negative (-)
Lock
N1-1 (UL) - Auxiliary battery positive (+)
N1-4 (L) - Auxiliary battery negative (-)
Unlock


If the result is not as specified, replace the rear door lock assembly LH.



b.

Check the operation of the door unlock detection switch. (w/ Smart Entry and Start System)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-6 (LSSR) - N1-9 (E) Lock 10 kΩ or higher
N1-6 (LSSR) - N1-9 (E) Unlock Below 1 Ω


If the result is not as specified, replace the rear door lock assembly LH.



Hide 69340 4.INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

a.
B228543C07
1.583,3.083 1.906,3.271 0.323,0.188 1.031,3.844 1.323,3.844 true 1.958,3.781 2.563,3.469 true 1.604,3.781 1,3.469 true 2.198,3.833 2.74,3.698 true 1.083,2.625 1.406,2.802 0.323,0.177 10 false *b 1.979,2.635 2.385,2.833 0.406,0.198 10 false *c 0.625,3.115 0.833,3.302 0.208,0.188 10 false *a 0.813,3.76 1.094,3.958 0.281,0.198 10 false DL 2.802,3.604 3.083,3.802 0.281,0.198 10 false UL 1.667,3.094 1.875,3.281 0.208,0.188 10 false N1 0.604,3.385 1.052,3.594 0.448,0.208 10 false UNDL 2.615,3.354 2.896,3.552 0.281,0.198 10 false L
*a Component without harness connected
(Rear Door Lock Assembly LH)
*b Lock
*c Unlock


Check the door lock motor operation.

i.

Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

Specified Condition:
Tester Connection Specified Condition
N1-2 (L) - Auxiliary battery positive (+)
N1-1 (UL) - Auxiliary battery negative (-)
Lock
N1-1 (UL) - Auxiliary battery positive (+)
N1-2 (L) - Auxiliary battery negative (-)
Unlock
N1-4 (DL) - Auxiliary battery positive (+)
N1-3 (UNDL) - Auxiliary battery negative (-)
Sets
N1-3 (UNDL) - Auxiliary battery positive (+)
N1-4 (DL) - Auxiliary battery negative (-)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double lockingsystem. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double lockingsystem. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock assembly LH.



b.
B228544C09
1.563,3 1.979,3.25 0.417,0.25 0.958,4.125 1.354,4.125 true 2.177,4.115 2.573,4.115 true 2.177,4.438 2.021,4.135 true 1.406,4.438 1.531,4.156 true 0.823,3.104 0.99,3.26 0.167,0.156 10 false *a 2.396,2.656 2.552,2.802 0.156,0.146 10 false *b 1.385,2.656 1.542,2.802 0.156,0.146 10 false *c 1.167,4.458 1.719,4.635 0.552,0.177 10 false DSSR 0.792,4.042 0.906,4.188 0.115,0.146 10 false E 2.625,4.031 3.104,4.208 0.479,0.177 10 false LSSR 2.167,4.469 2.281,4.615 0.115,0.146 10 false E 1.677,3.052 2.156,3.229 0.479,0.177 10 false N1
*a Component without harness connected
(Rear Door Lock Assembly RH)
*b Lock
*c Unlock


Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N1-5 (LSSR) - N1-6 (E) Lock 10 kΩ or higher
N1-5 (LSSR) - N1-6 (E) Unlock Below 1 Ω
N1-9 (DSSR) - N1-10 (E) Sets 10 kΩ or higher
N1-9 (DSSR) - N1-10 (E) Unsets Below 1 Ω


If the result is not as specified, replace the rear door lock assembly LH.