Use the following procedure to troubleshoot the telematics system.
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
The telematics system provides a variety of functions. Therefore, it is important to identify whether a malfunction is related to the communication system, including radio wave signal conditions, or any other systems. Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.
| Proceed to |
|---|
| NEXT |
NEXT
Measure the auxiliary battery voltage with the ignition switch off.
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
| Proceed to |
|---|
| NEXT |
NEXT
Use the GTS to check if the CAN communication system is functioning normally.
for Gasoline Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM
for HV Model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output. | A |
| CAN communication system DTCs are output. (for Gasoline Model) | B |
| CAN communication system DTCs are output. (for HV Model) | C |
A
B
C
Refer to DTC Check/Clear.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are output. | A |
| DTCs are not output. | B |
A
B
Refer to DTC Check/Clear.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.
| Proceed to |
|---|
| NEXT |
NEXT
Refer to DTC Check/Clear.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are output. | A |
| DTCs are not output. | B |
Even if the problem symptom has not been confirmed, check for DTCs. This is because the system stores history DTCs.
Check for DTCs and inspect the area that the code indicates.
A
B
Check for vehicle control history and note any codes that are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>VEHICLE CONTROL HISTORY
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| No vehicle control history is output. | A |
| Any vehicle control history is output. | B |
A
B
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>VEHICLE CONTROL HISTORY
Refer to Problem Symptoms Table.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table. | A |
| Fault is listed in Problem Symptoms Table. | B |
If the symptom does not recur and no DTCs are output, perform the simulation method.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
A
B
Refer to Terminals of ECU.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU
Refer to Data List / Active Test.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DATA LIST / ACTIVE TEST
| Proceed to |
|---|
| NEXT |
NEXT
Adjust, repair or replace as necessary.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>REGISTRATION
| Proceed to |
|---|
| NEXT |
NEXT
| Proceed to |
|---|
| NEXT |
NEXT