Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0424966 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and wireless door lock buzzer* answer-back function do not operate. In such cases, hazard warning light and wireless door lock buzzer* signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

*: w/ Wireless Door Lock Buzzer Answer-back Function


WIRING DIAGRAM

E408218E01
0.719,2.292 1.635,2.49 0.917,0.198 10 false A57 0.708,2.49 1.948,2.917 1.24,0.427 10 false Wireless Door Lock Buzzer 1.917,1.552 2.281,1.781 0.365,0.229 10 false 1 1.667,1.552 2.031,1.781 0.365,0.229 10 false B 0.76,1.542 1.125,1.771 0.365,0.229 10 false E 0.573,1.542 0.938,1.771 0.365,0.229 10 false 2 2.458,1.563 2.823,1.792 0.365,0.229 10 false 7 3.542,1.573 3.906,1.802 0.365,0.229 10 false 3 3.75,1.573 4.115,1.802 0.365,0.229 10 false BZR 3.688,3.115 4.292,3.375 0.604,0.26 10 false MB 3.688,3.323 5.323,4.01 1.635,0.688 10 false Main Body ECU (Multiplex Network Body ECU) 2.531,2.521 3.594,3.031 1.063,0.51 10 false Instrument Panel Junction Block Assembly 2.531,2.354 3.26,2.615 0.729,0.26 10 false 4D 0.677,4.375 2.552,4.646 1.875,0.271 10 false : CAN Communication Line 5.719,3.115 6.896,3.792 1.177,0.677 10 false Combination Meter Assembly 4.115,1.135 4.531,1.323 0.417,0.188 10 false +B

CAUTION / NOTICE / HINT

NOTICE:
·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

Before performing the inspection, check that DTC B124296 is not output.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Wireless Door Lock Buzzer Answer-back Function A
w/o Wireless Door Lock Buzzer Answer-back Function B



A

2.CHECK CUSTOMIZE SETTING USING GTS (Hazard Answer Back, Wireless Buzzer Resp, Wireless Buzzer Vol)

B

11.CHECK CUSTOMIZE SETTING USING GTS (Hazard Answer Back)
2.CHECK CUSTOMIZE SETTING USING GTS (Hazard Answer Back, Wireless Buzzer Resp, Wireless Buzzer Vol)
a.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Wireless Buzzer Response Function Function that enables/disables the wireless door lock buzzer response Enable $00:Disable,$01:Enable Main body ECU (Multiplex network body ECU)
Hazard Answer Back Function Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation Enable $00:Disable,$01:Enable Main body ECU (Multiplex network body ECU)
Wireless Buzzer Volume Setting Function that adjusts the wireless door lock buzzer volume Level5 $00:Level7(MAX),$01:Level6,$02:Level5,$03:Level4,$04:Level3,$05:Level2,$06:Level1,$07:Level0(MIN) Main body ECU (Multiplex network body ECU)
50006 1

Result:
Result Proceed to
All settings are Enable and other than Level0 A
A setting is Disable or Level0 B



A

3.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B

3.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock operates properly A
Wireless door lock/unlock does not operate properly B



A

4.READ VALUE USING GTS (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)

B

4.READ VALUE USING GTS (FR Door Lock Pos, FL Door Lock Pos, RR-Door Lock Pos SW, RL-Door Lock Pos SW)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Lock Position Switch Status Front door RH unlock detection switch signal Lock or Unlock Lock: Front door RH locked
Unlock: Front door RH unlocked
-
FL Door Lock Position Switch Status Front door LH unlock detection switch signal Lock or Unlock Lock: Front door LH locked
Unlock: Front door LH unlocked
-
RR Door Lock Position Switch Status Rear door RH unlock detection switch signal Lock or Unlock Lock: Rear door RH locked
Unlock: Rear door RH unlocked
-
RL Door Lock Position Switch Status Rear door LH unlock detection switch signal Lock or Unlock Lock: Rear door LH locked
Unlock: Rear door LH unlocked
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Lock Position Switch Status
FL Door Lock Position Switch Status
RR Door Lock Position Switch Status
RL Door Lock Position Switch Status
50003 449 20,21,22,23

OK:

The GTS display changes correctly in response to the lock/unlock operation.


Result:
Proceed to
OK
NG



OK

5.CHECK WIRELESS ANSWER-BACK OPERATION

NG

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

5.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur. (w/ Wireless Door Lock Buzzer Answer-back Function) A
Only hazard warning light answer-back does not occur. B



A

6.PERFORM ACTIVE TEST USING GTS (Wireless Buzzer)

B

9.CHECK HAZARD WARNING LIGHTS OPERATION
6.PERFORM ACTIVE TEST USING GTS (Wireless Buzzer)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 449 31
OK:

Wireless door lock buzzer sounds



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

7.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
7.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Disconnect the A57 wireless door lock buzzer connector.


b.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -
Body Electrical > Main Body > Active Test
Tester Display
Wireless Buzzer
50004 449 31

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-1 (B) - A57-2 (E) Active Test Wireless Buzzer is OFF Below 1 V
Active Test Wireless Buzzer is ON Pulse generation
(frequency: 2 kHz, high voltage: 11 to 14 V, low voltage: below 1 V)



Result:
Proceed to
OK
NG



OK

REPLACE WIRELESS DOOR LOCK BUZZER

NG

8.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
8.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-1 (B) - MB-3 (BZR) Always Below 1 Ω
A57-2 (E) - Body ground Always Below 1 Ω
A57-1 (B) or MB-3 (BZR) - Other terminals and body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

10.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - POWER DISTRIBUTION BOX ASSEMBLY)
9.CHECK HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning lights blink when the hazard warning signal switch is pressed.

OK:

Hazard warning lights blink.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)

10.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - POWER DISTRIBUTION BOX ASSEMBLY)
a.

Disconnect the 4D power distribution box assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-1 (B) - 4D-7 Always Below 1 Ω
A57-1 (B) or 4D-7 - Other terminals and body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

B

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK CUSTOMIZE SETTING USING GTS (Hazard Answer Back)
a.

Select the setting by referring to the table below.

Wireless Door Lock
Tester Display Description Default Setting ECU
Hazard Answer Back Function Function that flashes the hazard warning lights once when the doors are locked by wireless operation and twice when the doors are unlocked by wireless operation Enable $00:Disable,$01:Enable Main body ECU (Multiplex network body ECU)
50006 1

Result:
Result Proceed to
Customize setting is enable A
Customize setting is Disable B



A

3.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B