CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *1 | Power Distribution Box Assembly | *2 | Main Body ECU (Multiplex Network Body ECU) |
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
Reconnect the power distribution box assembly connectors.
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connectors connected.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| MB-13 (GND1) - Body ground | Ground | Always | Below 1 Ω |
| MB-14 (GND2) - Body ground | Ground | Always | Below 1 Ω |
| MB-26 (BECU) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| MB-27 (IGR) - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
Install the main body ECU (multiplex network body ECU) to the power distribution box assembly.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| 4E-5 (FRCY) - Body ground | Front door courtesy light switch (for RH) input | Front door RH open | Below 1 V |
| Front door RH closed | 11 to 14 V | ||
| 4E-3 (FLCY) - Body ground | Front door courtesy light switch (for LH) input | Front door LH open | Below 1 V |
| Front door LH closed | 11 to 14 V | ||
| 4E-1 (RCTY) - Body ground | Rear door courtesy light switch (for RH) input | Rear door RH open | Below 1 V |
| Rear door RH closed | Pulse generation | ||
| 4E-26 (LCTY) - Body ground | Rear door courtesy light switch (for LH) input | Rear door LH open | Below 1 V |
| Rear door LH closed | Pulse generation | ||
| 4E-2 (BCTY) - Body ground | Back door courtesy light switch input | Back door closed | Below 1 V |
| Back door open | 11 to 14 V | ||
| 4E-39 (TR+) - Body ground | Back door lock motor drive output | Back door closed → open | Below 1 V → 11 to 14 V → Below 1 V |
| 4E-37 (ACT-) - Body ground | Door lock motor unlock drive output | Door control switch or driver door key cylinder off → on (unlock) | Below 1 V → 11 to 14 V → Below 1 V |
| 4E-36 (ACT-) - Body ground | |||
| 4C-36 (ACT-) - Body ground | |||
| 4B-34 (ACT+) - Body ground | Door lock motor lock drive output | Door control switch or driver door key cylinder off → on (lock) | Below 1 V → 11 to 14 V → Below 1 V |
| 4B-19 (ACT+) - Body ground | |||
| 4E-14 (ACT+) - Body ground | |||
| 4E-15 (ACT+) - Body ground | |||
| H4-19 (BDSU) - Body ground* | Back door opener switch input | Back door opener switch pushed | Below 1 V |
| Back door opener switch not pushed | Pulse generation | ||
| H4-3 (LSFR) - Body ground | Front door RH unlock detection switch input | Front door RH unlocked | Below 1 V |
| Front door RH locked | Pulse generation | ||
| H4-9 (LSFL) - Body ground | Front door LH unlock detection switch input | Front door LH unlocked | Below 1 V |
| Front door LH locked | Pulse generation | ||
| H5-23 (LSWR) - Body ground | Rear door RH unlock detection switch input | Rear door RH unlocked | Below 1 V |
| Rear door RH locked | Pulse generation | ||
| H4-10 (LSWL) - Body ground | Rear door LH unlock detection switch input | Rear door LH unlocked | Below 1 V |
| Rear door LH locked | Pulse generation | ||
| H4-28 (L2) - Body ground | Driver door key-linked lock input | Driver door key cylinder turned to lock | Below 1 V |
| H4-28 (L2) - Body ground | Driver door key-linked lock input | Driver door key cylinder not turned | Pulse generation |
| H4-4 (UL3) - Body ground | Driver door key-linked unlock input | Driver door key cylinder turned to unlock | Below 1 V |
| H4-4 (UL3) - Body ground | Driver door key-linked unlock input | Driver door key cylinder not turned | Pulse generation |
*: w/o Entry and Start System
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H46-6 (+B) - Body ground | Ground | Always | Below 1 Ω |
| H46-29 (E) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
Reconnect the O47 certification ECU (smart key ECU assembly) connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| O47-16 (TSW5) - Body ground | Back door opener switch input | Back door opener switch assembly (open switch) off → on | Below 1 V → Pulse generation |
CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/ Double Locking System)
Disconnect the H42 double lock door control relay assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H42-12 (+B) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| H42-11 (CPUB) - Body ground | Auxiliary battery power supply | Ignition switch off | 11 to 14 V |
| H42-7 (GND) - Body ground | Ground | Always | Below 1 Ω |
Reconnect the H42 double lock door control relay assembly connector.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Tester Connection | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| H42-8 (ACTS) - Body ground | All door double lock motor set on output | Double lock unset | Below 1 V |
| Double lock set | 11 to 14 V | ||
| H42-1 (ACTR) - Body ground | All door double lock motor set off output | Double lock set | Below 1 V |
| Double lock unset | 11 to 14 V | ||
| H42-6 (DLPD) - Body ground | Front RH double lock position switch input | Double lock unset | Pulse generation |
| Double lock set | Below 1 V | ||
| H42-5 (DLPP) - Body ground | Front LH double lock position switch input | Double lock unset | Pulse generation |
| Double lock set | Below 1 V | ||
| H42-4 (DLPR) - Body ground | Rear RH double lock position switch input | Double lock unset | Pulse generation |
| Double lock set | Below 1 V | ||
| H42-3 (DLPL) - Body ground | Rear LH double lock position switch input | Double lock unset | Pulse generation |
| Double lock set | Below 1 V |