Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for Gasoline Model without Entry and Start System) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424970 IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System)  TERMINALS OF ECU  


CHECK TRANSPONDER KEY ECU ASSEMBLY


B460711E07
3.365,0.375 3.781,0.635 0.417,0.26 3.448,0.417 3.906,0.615 0.458,0.198 10 false H74

a.

Disconnect the H74 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item / DTC
H74-4 (+B) - H74-12 (GND) Auxiliary battery Always 11 to 14 V +B
H74-5 (KSW) - H74-12 (GND) Unlock warning switch signal No door control transmitter assembly in ignition key cylinder 10 kΩ or higher
·

B2780

·

Key SW


Door control transmitter assembly in ignition key cylinder Below 1 Ω
H74-12 (GND) - Body ground Ground Always Below 1 Ω -


c.

Reconnect the H74 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item / DTC
H74-6 (IG) - H74-12 (GND) Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
H74-8 (IND) - H74-12 (GND) Security indicator light signal No door control transmitter assembly in ignition key cylinder, or 20 sec. elapsed after turning ignition switch to ACC or off (immobiliser system set) Pulse generation Immobiliser
Door control transmitter assembly in ignition key cylinder (immobiliser system unset) Below 1 V
H74-9 (D) - H74-12 (GND) DLC3 communication Without communication Below 1 V -
During communication Pulse generation
H74-2 (ANT1) - H74-12 (GND) Transponder key amplifier power source No door control transmitter assembly in ignition key cylinder Below 1 V -
Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder Pulse generation
(See waveform 1)
H74-3 (ANT2) - H74-12 (GND) Transponder key amplifier communication signal No door control transmitter assembly in ignition key cylinder Below 1 V -
Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder Pulse generation
(See waveform 2)
H74-10 (EFII) - H74-12 (GND) ECM input signal Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal Pulse generation
(See waveform 3)
H74-11 (EFIO) - H74-12 (GND) ECM output signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B329909N02
5.76,0.854 6.219,1.052 0.458,0.198 10 GND

Measurement Condition
Item Content
Tester Connection H74-2 (ANT1) - H74-12 (GND)
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder


ii.

Waveform 2 (Reference)

B532691N01
5.75,0.813 6.208,1.01 0.458,0.198 10 false GND

Measurement Condition
Item Content
Tester Connection H74-3 (ANT2) - H74-12 (GND)
Tool Setting 20 V/DIV., 2 s./DIV.
Condition Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder


iii.

Waveform 3 (Reference)

B325134C02
0.906,1.25 1.365,1.448 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection H74-10 (EFII) - H74-12 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal


iv.

Waveform 4 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection H74-11 (EFIO) - H74-12 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal




CHECK ECM (for M15A-FKS)


A458815E02
1.781,0.156 2.198,0.458 0.417,0.302 5.385,0.188 5.802,0.49 0.417,0.302 1.875,0.229 2.385,0.448 0.51,0.219 11 false D51 5.479,0.26 5.99,0.479 0.51,0.219 11 false A54

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item / DTC
A54-47 (IMO) - A54-10 (E1) Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal Pulse generation
(See waveform 1)
-
A54-61 (IMI) - A54-10 (E1) Transponder key ECU assembly communication input Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C01
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A54-47 (IMO) - A54-10 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal


ii.

Waveform 2 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A54-61 (IMI) - A54-10 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal




CHECK ECM (for 1KR-FE)


A325174E06
2.396,0.448 2.823,0.719 0.427,0.271 5.406,0.469 5.833,0.74 0.427,0.271 5.5,0.521 5.958,0.719 0.458,0.198 10 false A55 2.5,0.5 2.958,0.698 0.458,0.198 10 false D50

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item / DTC
A55-43 (IMO) - A55-4 (E1) Transponder key ECU assembly communication output Ignition switch off 11 to 14 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal Pulse generation
(See waveform 1)
-
A55-42 (IMI) - A55-4 (E1) Transponder key ECU assembly communication input Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

i.

Waveform 1 (Reference)

B333258C01
0.865,1.271 1.323,1.469 0.458,0.198 10 GND 2.719,1.354 2.885,1.521 0.167,0.167 10 *a 2.906,1.354 3.073,1.521 0.167,0.167 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A55-43 (IMO) - A55-4 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal


ii.

Waveform 2 (Reference)

B333259C01
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A55-42 (IMI) - A55-4 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal