Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (for Gasoline Model without Entry and Start System) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424970 IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(for Gasoline Model without Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the door control transmitter assembly and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

for M15A-FKS:
E366879E32
1.615,0.99 2.073,1.188 0.458,0.198 10 false IMO 1.656,1.802 2.115,2 0.458,0.198 10 false IMI 1.99,0.99 3,1.219 1.01,0.229 10 false 47 1.969,1.813 2.833,2.104 0.865,0.292 10 false 61 5.021,1 5.479,1.198 0.458,0.198 10 false 10 5.021,1.792 5.479,1.99 0.458,0.198 10 false 11 5.292,0.99 5.75,1.188 0.458,0.198 10 false EFII 4.948,2.802 5.406,3 0.458,0.198 10 false H74 5.302,1.792 5.76,1.99 0.458,0.198 10 false EFIO 1.115,2.844 2.104,3.042 0.99,0.198 10 false A54 1.104,3.021 1.875,3.323 0.771,0.302 10 false ECM 4.938,2.958 6.969,3.479 2.031,0.521 10 false Transponder Key ECU Assembly 1.344,1.375 1.802,1.573 0.458,0.198 10 false 12 V 6.01,0.542 6.469,0.74 0.458,0.198 10 false 12 V

for 1KR-FE:
E366879E33
1.615,0.99 2.073,1.188 0.458,0.198 10 false IMO 1.656,1.802 2.115,2 0.458,0.198 10 false IMI 1.99,0.99 3,1.219 1.01,0.229 10 false 43 1.969,1.813 2.833,2.104 0.865,0.292 10 false 42 5.021,1 5.479,1.198 0.458,0.198 10 false 10 5.021,1.792 5.479,1.99 0.458,0.198 10 false 11 5.292,0.99 5.75,1.188 0.458,0.198 10 false EFII 4.948,2.802 5.406,3 0.458,0.198 10 false H74 5.302,1.792 5.76,1.99 0.458,0.198 10 false EFIO 1.115,2.844 2.104,3.042 0.99,0.198 10 false A55 1.104,3.021 1.875,3.323 0.771,0.302 10 false ECM 4.938,2.958 6.969,3.479 2.031,0.521 10 false Transponder Key ECU Assembly 1.344,1.375 1.802,1.573 0.458,0.198 10 false 12 V 6.01,0.542 6.469,0.74 0.458,0.198 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for M15A-FKS A
for 1KR-FE B



A

2.CLEAR DTC

B

12.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

4.READ VALUE USING GTS (IMMOBILISER FUEL CUT STARTS / IMMOBILISER FUEL CUT)

B

4.READ VALUE USING GTS (IMMOBILISER FUEL CUT STARTS / IMMOBILISER FUEL CUT)
a.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK WHETHER ENGINE STARTS
5.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
6.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.


B460719C09
3.167,0.052 3.583,0.323 0.417,0.271 2.781,1.906 3.042,1.115 true 3.229,0.104 3.688,0.302 0.458,0.198 10 false H74 0.74,3.375 1.198,3.573 0.458,0.198 10 false GND 1.135,0.156 1.448,0.375 0.313,0.219 10 false *a 1.885,4.083 2.198,4.302 0.313,0.219 10 false *c 2.625,1.969 3.083,2.167 0.458,0.198 10 false EFIO 3.74,4.073 4.052,4.292 0.313,0.219 10 false *c 2.385,4.802 2.698,5.021 0.313,0.219 10 false *d 4.396,4.813 4.708,5.031 0.313,0.219 10 false *d 2.458,5.063 2.771,5.281 0.313,0.219 10 false *e 4.344,5.063 4.656,5.281 0.313,0.219 10 false *e 2.188,2.354 2.5,2.573 0.313,0.219 10 false *b
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Waveform (detail) *d Approximately 40 ms.
*e Approximately 60 ms. - -


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

7.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)

B

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
7.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.


B463094C15
3.417,0.333 3.833,0.604 0.417,0.271 3.073,2.323 3.365,1.573 true 2.74,4.552 2.875,4.094 true 3.177,4.531 3.063,4.094 true 0.927,4.063 1.385,4.26 0.458,0.198 10 false GND 0.365,0.188 0.792,0.5 0.427,0.313 10 false *a 2.906,3.125 3.333,3.438 0.427,0.313 10 false *b 3.49,0.375 3.927,0.646 0.438,0.271 10 false H74 2.76,2.302 3.219,2.5 0.458,0.198 10 false EFII 2.563,4.542 2.875,4.76 0.313,0.219 10 false *c 3.198,4.552 3.51,4.771 0.313,0.219 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-10 (EFII) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

8.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

B

8.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B463095C22
3.396,0.385 3.781,0.656 0.385,0.271 2.99,2.198 3.229,1.552 true 3.24,4.563 3.292,4.083 true 3.521,4.563 3.479,4.083 true 0.375,0.125 0.688,0.323 0.313,0.198 10 false *a 3.458,0.427 3.771,0.625 0.313,0.198 10 false H74 2.646,2.219 3.104,2.448 0.458,0.229 10 false EFIO 3.333,3.021 3.792,3.25 0.458,0.229 10 false *b 0.958,4.042 1.417,4.271 0.458,0.229 10 false GND 3.052,4.531 3.313,4.719 0.26,0.188 10 false *c 3.552,4.552 3.813,4.74 0.26,0.188 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK
Tester Connection Condition Tool Setting Specified Condition
H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

9.REGISTER ECU COMMUNICATION ID

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

9.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the H74 transponder key ECU assembly connector.


b.

Disconnect the A54 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-11 (EFIO) - A54-61 (IMI) Always Below 1 Ω
H74-11 (EFIO) or A54-61 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

13.CHECK FOR DTC
13.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

14.READ VALUE USING GTS (IMMOBILISER FUEL CUT STARTS / IMMOBILISER FUEL CUT)

B

14.READ VALUE USING GTS (IMMOBILISER FUEL CUT STARTS / IMMOBILISER FUEL CUT)
a.

Read the Data List according to the display on the GTS.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

15.CHECK WHETHER ENGINE STARTS
15.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

16.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
16.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.


B460719C09
3.167,0.052 3.583,0.323 0.417,0.271 2.781,1.906 3.042,1.115 true 3.229,0.104 3.688,0.302 0.458,0.198 10 false H74 0.74,3.375 1.198,3.573 0.458,0.198 10 false GND 1.135,0.156 1.448,0.375 0.313,0.219 10 false *a 1.885,4.083 2.198,4.302 0.313,0.219 10 false *c 2.625,1.969 3.083,2.167 0.458,0.198 10 false EFIO 3.74,4.073 4.052,4.292 0.313,0.219 10 false *c 2.385,4.802 2.698,5.021 0.313,0.219 10 false *d 4.396,4.813 4.708,5.031 0.313,0.219 10 false *d 2.458,5.063 2.771,5.281 0.313,0.219 10 false *e 4.344,5.063 4.656,5.281 0.313,0.219 10 false *e 2.188,2.354 2.5,2.573 0.313,0.219 10 false *b
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Waveform (detail) *d Approximately 40 ms.
*e Approximately 60 ms. - -


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

17.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)

B

21.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
17.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFII)
a.

Using an oscilloscope, check the waveform.


B463094C15
3.417,0.333 3.833,0.604 0.417,0.271 3.073,2.323 3.365,1.573 true 2.74,4.552 2.875,4.094 true 3.177,4.531 3.063,4.094 true 0.927,4.063 1.385,4.26 0.458,0.198 10 false GND 0.365,0.188 0.792,0.5 0.427,0.313 10 false *a 2.906,3.125 3.333,3.438 0.427,0.313 10 false *b 3.49,0.375 3.927,0.646 0.438,0.271 10 false H74 2.76,2.302 3.219,2.5 0.458,0.198 10 false EFII 2.563,4.542 2.875,4.76 0.313,0.219 10 false *c 3.198,4.552 3.51,4.771 0.313,0.219 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


Measurement Condition
Tester Connection Condition Tool Setting Specified Condition
H74-10 (EFII) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)

Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

18.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)

B

18.INSPECT TRANSPONDER KEY ECU ASSEMBLY (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B463095C22
3.396,0.385 3.781,0.656 0.385,0.271 2.99,2.198 3.229,1.552 true 3.24,4.563 3.292,4.083 true 3.521,4.563 3.479,4.083 true 0.375,0.125 0.688,0.323 0.313,0.198 10 false *a 3.458,0.427 3.771,0.625 0.313,0.198 10 false H74 2.646,2.219 3.104,2.448 0.458,0.229 10 false EFIO 3.333,3.021 3.792,3.25 0.458,0.229 10 false *b 0.958,4.042 1.417,4.271 0.458,0.229 10 false GND 3.052,4.531 3.313,4.719 0.26,0.188 10 false *c 3.552,4.552 3.813,4.74 0.26,0.188 10 false *d
*a Component with harness connected
(Transponder Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK
Tester Connection Condition Tool Setting Specified Condition
H74-11 (EFIO) - Body ground Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) auxiliary battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)


Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

19.REGISTER ECU COMMUNICATION ID

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

19.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.


Result:
Proceed to
NEXT



NEXT

20.CHECK WHETHER ENGINE STARTS
20.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the H74 transponder key ECU assembly connector.


b.

Disconnect the A55 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H74-11 (EFIO) - A55-42 (IMI) Always Below 1 Ω
H74-11 (EFIO) or A55-42 (IMI) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR