Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B574584E04
3.375,0.406 3.792,0.656 0.417,0.25 4.802,0.406 5.219,0.656 0.417,0.25 1.969,0.417 2.385,0.667 0.417,0.25 4.896,0.438 5.208,0.635 0.313,0.198 10 false H46 3.458,0.438 3.771,0.635 0.313,0.198 10 false O47 2.052,0.448 2.365,0.646 0.313,0.198 10 false H45

a.

Disconnect the H45 and H46 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition Related Data List Item/DTC
H45-15 (NE) - Body ground Engine speed signal Always 10 kΩ or higher
Power Source Control

Engine Condition


H45-21 (STP1) - Body ground Stop light switch signal*1 Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less
Power Source Control

Stop Light Switch


H46-6 (+B) - H46-29 (E) Power source Always 11 to 14 V -
H45-22 (CUTB) - Body ground Dark current cut pin*2 Always 11 to 14 V -
H46-29 (E) - Body ground GND Always Below 1 Ω -
H46-23 (SSW3) - Body ground SSW3 contact signal Engine switch pushed → Engine switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 3


H46-27 (SSW2) - Body ground SSW2 contact signal Engine switch pushed → Engine switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 2


H46-19 (SSW1) - Body ground SSW1 contact signal Engine switch pushed → Engine switch not pushed Below 15 Ω → 10 kΩ or higher
Power Source Control

Push Start Switch 1


H45-13 (SPD) - Body ground Vehicle speed signal Always 30 kΩ or higher
Power Source Control

Vehicle Running Condition (Line)



*1: for CVT

*2: In order to prevent the vehicle auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Connect the H45 and H46 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition Related Data List Item/DTC
H45-3 (STA) - H46-29 (E) When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started".
for Manual Transaxle

Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


for CVT

Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


6 V or higher*1 → 1.0 V or less -
H45-10 (STAR) - H46-29 (E)
Outputs voltage to the starter relay
·

Outputs voltage (12 V) to the starter relay when starting the engine. (Max. 30 sec. Turns off when an engine speed of 1000 rpm.)


HINT:

When Hi is selected, a start request signal (STAR) will not be output even though a start request signal (STSW) is input.


for Manual Transaxle

Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


for CVT

Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


6 V or higher*1 → 1.0 V or less -
H45-15 (NE) - Body ground Engine speed signal Idling (engine warmed up) Pulse generation
(See waveform 5)
Power Source Control

Engine Condition


H45-21 (STP1) - H46-29 (E) Stop light switch signal*1 Brake pedal depressed → Brake pedal released 9 V or higher → 1 V or less
Power Source Control

Stop Light Switch


H46-11 (SLP) - H46-29 (E) Steering lock position signal Steering locked → Steering unlocked 11 to 14 V → 1.5 V or less
Power Source Control

Steering Unlock Switch


H46-24 (SLR+) - H46-29 (E) Steering lock motor operation command signal
(Steering lock motor operation permission signal sent from the certification ECU (smart key ECU assembly))
When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift lever is in P.*1


Pulse generation
(See waveform 1)
-
H46-8 (LIN) - H46-29 (E) LIN communication line Ignition switch ON Pulse generation
Entry&Start

Steering Lock Start Condition


H46-14 (P) - H46-29 (E) P position signal*1 Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less
Power Source Control

Shift P Signal


H46-23 (SSW3) - H46-29 (E) SSW3 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 3


H46-27 (SSW2) - H46-29 (E) SSW2 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 2


H46-19 (SSW1) - H46-29 (E) SSW1 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → 1 V or less
Power Source Control

Push Start Switch 1


H46-21 (ACCD) - H46-29 (E) ACC signal Ignition switch off → Ignition switch ACC 1 V or less → 8.5 V or higher
Power Source Control

ACC Relay Monitor


H45-11 (IGRD) - H46-29 (E) IG signal Ignition switch off → Ignition switch ON 1 V or less → 9 V or higher
Power Source Control

IGR Relay Circuit (Outside) Monitor


H45-24 (IGPD) - H46-29 (E) IG signal Ignition switch off → Ignition switch ON 1 V or less → 9 V or higher
Power Source Control

IGP Relay Circuit (Outside) Monitor


H45-13 (SPD) - H46-29 (E) Vehicle speed signal Vehicle being driven at approx. 5 km/h (3 mph) Pulse generation
(See waveform 2)
Power Source Control

Vehicle Running Condition (Line)


H46-4 (CLG5) - H46-29 (E) Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
H46-5 (CG5B) - H46-29 (E) Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
O47-10 (CLG7) - H46-29 (E) Output to No. 2 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
O47-9 (CG7B) - H46-29 (E) Output to No. 2 indoor electrical key antenna assembly (rear floor) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 3)
-
H46-30 (AGND) - Body ground Transponder key amplifier ground Always Below 1 Ω -
H46-12 (ANT1) - H46-30 (AGND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 4)
Entry&Start

Encrypt Code Difference


H46-13 (ANT2) - H46-30 (AGND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 4)
H46-25 (IND) - H46-29 (E) Security indicator output Ignition switch off → ON Pulse generation → Below 2 V -

*1: for CVT


HINT:
·

The waveform of the steering lock actuator motor stopped can be checked without performing any particular operation.

·

The waveform of the steering lock actuator motor operating can be checked if either of the following operations is performed:

-

To unlock the steering, bring the electrical key transmitter sub-assembly into the cabin and turn the ignition switch to ACC or ON.

-

To lock the steering, open a door with the ignition switch off and the shift lever in P (for CVT).


·

*1: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.




e.

Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C221561C09
1.521,1.583 2.375,1.74 0.854,0.156 2.281,0.479 2.729,0.635 0.448,0.156 0.24,0.417 1.635,0.615 1.396,0.198 2.01,1.75 2.198,2.042 2.198,2.042 2.323,2.042 false 0.948,0.406 2.927,0.25 2.927,0.25 2.521,0.479 false 2.927,1.594 3.313,1.792 0.385,0.198 10 GND 2.969,0.146 3.208,0.385 0.24,0.24 10 *a 2.375,1.979 2.552,2.146 0.177,0.167 10 *b
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1

Measurement Condition
Item Content
Tester Connection H46-24 (SLR+) - H46-29 (E)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition When a door is opened, the steering lock motor will be operated if all of the following conditions are met:
·

The steering is unlocked.

·

The ignition switch is off.

·

The shift lever is in P.*1



*1: for CVT



ii.
B220145N21
2.875,1.177 3.229,1.344 0.354,0.167 10 false GND

Waveform 2

Measurement Condition
Item Content
Tester Connection H45-13 (SPD) - H46-29 (E)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Vehicle being driven at approx. 5 km/h (3 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



iii.
B574602C02
0.385,0.99 0.844,1.188 0.458,0.198 10 false GND 1.292,1.906 1.75,2.104 0.458,0.198 10 false *a 2.5,1.906 2.958,2.104 0.458,0.198 10 false *b
*a For 30 seconds after any door closed
*b After 30 seconds or more have elapsed since any door closed


Waveform 3

Measurement Condition
Item Content
Tester Connection H46-4 (CLG5) - H46-29 (E)
H46-5 (CG5B) - H46-29 (E)
O47-10 (CLG7) - H46-29 (E)
O47-9 (CG7B) - H46-29 (E)
Tool Setting 5 V/DIV., 500 ms./DIV.
Condition Procedure:
1.

Ignition switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door




iv.
B574585N01
0.427,1 0.885,1.198 0.458,0.198 10 false GND

Waveform 4

Measurement Condition
Item Content
Tester Connection H46-12 (ANT1) - H46-30 (AGND)
H46-13 (ANT2) - H46-30 (AGND)
Tool Setting 20 V/DIV., 200 ms./DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed


v.
C222647N06
2.969,1.75 3.375,1.938 0.406,0.188 10 GND

Waveform 5

Measurement Condition
Item Content
Tester Connection H45-15 (NE) - Body ground
Tool Setting 2 V/DIV., 2 ms./DIV.
Condition Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.





CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


C396298E05
1.75,0.792 2.146,1.063 0.396,0.271 1.823,0.833 2.281,1.031 0.458,0.198 10 false H71

a.

Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H71-1 (GND) - Body ground Ground Always Below 1 Ω -
H71-7 (B) - Body ground Constant power supply Ignition switch off 11 to 14 V -


c.

Connect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Measure the voltage, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H71-3 (IGE) - H71-1 (GND) Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P*1

·

Steering unlocked

·

Ignition switch turned off


Pulse generation
(See waveform 1)
Entry&Start
·

Power Supply Short History

·

Unlock Request Receive

·

Steering Lock Request Receive


H71-4 (SLP1) - H71-1 (GND) Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked 11 to 14 V → Below 1.5 V
Entry&Start

Sensor Malfunction History


H71-5 (LIN) - H71-1 (GND) LIN communication line Ignition switch ON Pulse generation
Entry&Start

Steering Lock Start Condition


H71-6 (SLA) - H71-1 (GND) Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Ignition switch off → ON Below 1 V → 11 to 14 V -

*1: for CVT


HINT:
·

There is 1 motor and 2 sensors built into the steering lock actuator or upper bracket assembly.

·

When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

·

In order to take measurements when the lock motor is operating, perform either of the following operations:

-

To unlock the steering, carry the key and turn the ignition switch to ACC or ON.

-

To lock the steering, turn the ignition switch off with the shift lever in P (for CVT), and then open a door.





e.
C221561C69
1.542,1.583 2.396,1.74 0.854,0.156 2.271,0.479 2.719,0.635 0.448,0.156 0.24,0.427 1.635,0.625 1.396,0.198 0.896,0.427 2.75,0.25 2.75,0.25 2.938,0.25 false 2.75,0.25 2.5,0.469 false 1.969,1.74 2.094,2.042 2.094,2.042 2.177,2.042 false 2.927,1.604 3.313,1.802 0.385,0.198 10 false GND 2.99,0.198 3.24,0.417 0.25,0.219 10 false *a 2.229,1.969 2.479,2.135 0.25,0.167 10 false *b
*a Steering lock motor not operating
*b Steering lock motor operating


Using an oscilloscope, check the waveform of the ECU.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1

Measurement Condition
Item Content
Tester Connection H71-3 (IGE) - H71-1 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Steering lock motor operating when all conditions met, and then door opened:
·

Shift lever in P*1

·

Steering unlocked

·

Ignition switch turned off



*1: for CVT




CHECK ID CODE BOX (IMMOBILISER CODE ECU) (for TMMF Made)


B510664E04
3.302,0.125 3.677,0.406 0.375,0.281 3.385,0.198 3.844,0.396 0.458,0.198 10 false H67

a.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition Related Data List Item
H67-1 (+B) - Body ground Power source Ignition switch off 11 to 14 V -
H67-5 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the H67 ID code box (immobiliser code ECU) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition Related Data List Item
H67-3 (EFII) - H67-5 (GND) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V Entry&Start
·

EFI Code Receive

·

Start Request


H67-3 (EFII) - H67-5 (GND) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
H67-4 (EFIO) - H67-5 (GND) EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch off Below 1 V
H67-4 (EFIO) - H67-5 (GND) EFI communication output
(Signal output from ID code box (immobiliser code ECU) to ECM)
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 2)
H67-2 (LIN1) - H67-5 (GND) LIN communication line Ignition switch ON Pulse generation Entry&Start
·

Steering Lock Start Cond




e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Item Content
Tester Connection H67-3 (EFII) - H67-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Item Content
Tester Connection H67-4 (EFIO) - H67-5 (GND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery




CHECK ECM (for M15A-FKS)


A458815N01
1.781,0.156 2.198,0.458 0.417,0.302 5.385,0.188 5.802,0.49 0.417,0.302 1.875,0.229 2.385,0.448 0.51,0.219 11 false D51 5.479,0.26 5.99,0.479 0.51,0.219 11 false A54

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
A54-2 (IGP) - A54-10 (E1) Ignition power supply Ignition switch ON 11 to 14 V -
A54-13 (IGR) - A54-10 (E1) Ignition power supply Ignition switch ON 11 to 14 V -
A54-1 (BATT) - A54-10 (E1) +B power supply Always 11 to 14 V -
A54-10 (E1) - Body ground Ground Always Below 1 Ω -
A54-23 (NSW) - A54-10 (E1) Park/Neutral position switch assembly signal*1 Ignition switch ON, shift lever not in P or N 11 to 14 V -
Ignition switch ON, shift lever in P or N Below 3.0 V -
Clutch start switch signal*2 Ignition switch ON, clutch pedal fully released 11 to 14 V -
Ignition switch ON, clutch pedal depressed Below 3.0 V -
A54-39 (KSW) - A54-10 (E1) Key in vehicle signal Key outside vehicle 11 to 14 V -
A54-47 (IMO) - A54-10 (E1) EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))*3
Ignition switch off 11 to 14 V
Entry&Start
·

EFI Code Receive

·

Engine Start Request


EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))*4
A54-47 (IMO) - A54-10 (E1) EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))*3
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))*4
A54-61 (IMI) - A54-10 (E1) EFI communication input
(Signal output from certification ECU (smart key ECU assembly) to ECM)*3
Ignition switch off 1 V or less
EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)*4
A54-61 (IMI) - A54-10 (E1) EFI communication input
(Signal output from certification ECU (smart key ECU assembly) to ECM)*3
Ignition switch turned to ON using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)*4
A54-16 (NEO) - A54-10 (E1) Engine speed signal Idling (engine warmed up) Pulse generation
(See waveform 3)
Power Source Control

Engine Condition


A54-30 (STA) - A54-10 (E1) When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started". Engine is cranking 6 V or higher -

*1: for CVT

*2: for Manual Transaxle

*3: for TMC Made

*4: for TMMF Made



b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C22
0.896,1.24 1.354,1.438 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A54-47 (IMO) - A54-10 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A54-61 (IMI) - A54-10 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch turned to ON using registered electrical key transmitter sub-assembly


iii.
A431371E02
2.833,0.938 3.292,1.135 0.458,0.198 10 false GND

Waveform 3

Measurement Condition
Item Content
Tester Connection A54-16 (NEO) - A54-10 (E1)
Tool Setting 5 V/DI., 20 ms./DIV.
Condition Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.





CHECK ECM (for 1KR-FE)


A325174E06
2.396,0.448 2.823,0.719 0.427,0.271 5.406,0.469 5.833,0.74 0.427,0.271 5.5,0.521 5.958,0.719 0.458,0.198 10 false A55 2.5,0.5 2.958,0.698 0.458,0.198 10 false D50

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
A55-31 (IGR) - A55-4 (E1) Ignition power supply Ignition switch ON 11 to 14 V -
A55-15 (BATT) - A55-4 (E1) +B power supply Always 11 to 14 V -
A55-4 (E1) - Body ground Ground Always Below 1 Ω -
A55-43 (IMO) - A55-4 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Ignition switch off 11 to 14 V
Entry&Start
·

EFI Code Receive

·

Engine Start Request


A55-43 (IMO) - A55-4 (E1) EFI communication input
(Signal input from ECM to ID code box (immobiliser code ECU))
Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery Pulse generation
(See waveform 1)
A55-42 (IMI) - A55-4 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch off 1 V or less
A55-42 (IMI) - A55-4 (E1) EFI communication input
(Signal output from ID code box (immobiliser code ECU) to ECM)
Ignition switch turned to ON using registered electrical key transmitter sub-assembly Pulse generation
(See waveform 2)
A55-44 (NEO) - A55-4 (E1) Engine speed signal Idling (engine warmed up) Pulse generation
(See waveform 3)
Power Source Control

Engine Condition


A55-46 (STA) - A55-4 (E1) When starting the engine, this monitors the voltage sent from terminal STAR to the starter relay to judge whether the engine is "being started". Engine is cranking 6 V or higher -
D50-111 (NSW) - A55-4 (E1) Clutch start switch signal Ignition switch ON (Clutch pedal fully depressed) Below 1.5 V -
Ignition switch ON (Clutch pedal released) 11 to 14 V -


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C22
0.896,1.24 1.354,1.438 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A55-43 (IMO) - A55-4 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms. *b Approximately 270 ms.


Measurement Condition
Item Content
Tester Connection A55-42 (IMI) - A55-4 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch turned to ON using registered electrical key transmitter sub-assembly


iii.
A431371E02
2.833,0.938 3.292,1.135 0.458,0.198 10 false GND

Waveform 3

Measurement Condition
Item Content
Tester Connection A55-44 (NEO) - A55-4 (E1)
Tool Setting 5 V/DI., 20 ms./DIV.
Condition Idling (engine warmed up)

HINT:

The wavelength becomes shorter as the engine speed increases.





CHECK ENGINE SWITCH


B516200E01
3.365,0.208 3.76,0.458 0.396,0.25 3.448,0.25 3.906,0.448 0.458,0.198 10 false H68

a.

Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H68-3 (GND) - Body ground Transponder key amplifier ground Always Below 1 Ω -
H68-11 (SS3) - H68-3 (GND) SS3 contact signal
HINT:

Backup for SS1. Behaves the same way as SS1.


Engine switch not pushed → Engine switch pushed 9 V or higher → Below 1 V
Power Source Control

Start Switch 3


H68-6 (SS2) - H68-3 (GND) SS2 contact signal
HINT:

Backup for SS1. Behaves the same way as SS1.


Engine switch not pushed → Engine switch pushed 9 V or higher → Below 1 V
Power Source Control

Start Switch 2


H68-12 (SS1) - H68-3 (GND) SS1 contact signal Engine switch not pushed → Engine switch pushed 9 V or higher → Below 1 V
Power Source Control

Start Switch 1




b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition Related Data List Item/DTC
H68-1 (ANT1) - H68-3 (GND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 1)
Entry&Start

Encrypt Code Difference

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



H68-7 (ANT2) - H68-3 (GND) Signal input / output from transponder key coil (transponder key coil built into engine switch) Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed Pulse generation
(See waveform 1)


c.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B574585N01
0.427,1 0.885,1.198 0.458,0.198 10 false GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection H68-1 (ANT1) - H68-3 (GND)
H68-7 (ANT2) - H68-3 (GND)
Tool Setting 20 V/DIV., 200 ms./DIV.
Condition Ignition switch off, electrical key transmitter sub-assembly not in cabin, within 30 seconds of engine switch pressed