Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  B279A12  Engine Immobiliser System Circuit Short to Battery  B279A9A  Engine Immobiliser System Component or System Operating Conditions  


DESCRIPTION

for TMC Made:

If the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM will store this DTC.


for TMMF Made:

If the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM will store this DTC.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A12 Engine Immobiliser System Circuit Short to Battery
for TMC Made:

The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high. (1 trip detection logic*)


for TMMF Made:

The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high. (1 trip detection logic*)


for TMC Made:
·

Certification ECU (smart key ECU assembly)

·

ECM

·

Wire harness or connector


for TMMF Made:
·

ID code box (immobiliser code ECU)

·

ECM

·

Wire harness or connector


DTC output confirmation operation:

Turn the ignition switch to ON and wait 6 seconds.


B279A9A Engine Immobiliser System Component or System Operating Conditions

The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high. (1 trip detection logic*)


·

ID code box (immobiliser code ECU)

·

ECM

·

Wire harness or connector


DTC output confirmation operation:
Turn the ignition switch to ON and wait 6 seconds.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
B279A12 -
B279A9A

WIRING DIAGRAM

for TMC Made with M15A-FKS


B463091E67
0.51,1.865 2.365,2.135 1.854,0.271 10 false ECM 0.51,1.698 0.969,1.896 0.458,0.198 10 false A54 0.854,0.219 1.313,0.417 0.458,0.198 10 false +B 1.865,0.729 2.323,0.927 0.458,0.198 10 false IMI 2.177,0.719 2.635,0.917 0.458,0.198 10 false 61 4.917,0.719 5.375,0.917 0.458,0.198 10 false 5 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.677 5.583,1.875 0.458,0.198 10 false H45 5.125,1.844 6.927,2.26 1.802,0.417 10 false Certification ECU (Smart Key ECU Assembly)


for TMMF Made with M15A-FKS


B463091E70
0.51,1.865 2.365,2.135 1.854,0.271 10 false ECM 0.51,1.698 0.969,1.896 0.458,0.198 10 false A54 0.854,0.219 1.313,0.417 0.458,0.198 10 false +B 1.865,0.729 2.323,0.927 0.458,0.198 10 false IMI 2.177,0.719 2.635,0.917 0.458,0.198 10 false 61 4.917,0.719 5.375,0.917 0.458,0.198 10 false 4 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.677 5.583,1.875 0.458,0.198 10 false H67 5.125,1.844 6.698,2.229 1.573,0.385 10 false ID Code Box (Immobiliser Code ECU)


for 1KR-FE


B463091E71
0.51,1.875 2.365,2.146 1.854,0.271 10 false ECM 0.51,1.698 0.958,1.896 0.448,0.198 10 false A55 0.854,0.219 1.313,0.417 0.458,0.198 10 false +B 1.865,0.729 2.323,0.927 0.458,0.198 10 false IMI 2.177,0.719 2.635,0.917 0.458,0.198 10 false 42 4.917,0.719 5.375,0.917 0.458,0.198 10 false 4 5.135,0.719 5.594,0.917 0.458,0.198 10 false EFIO 5.125,1.677 5.583,1.875 0.458,0.198 10 false H67 5.125,1.844 6.698,2.26 1.573,0.417 10 false ID Code Box (Immobiliser Code ECU)


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the ECM, certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to the Service Bulletin.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

*1: for TMC Made

*2: for TMMF Made




HINT:

When DTC B279A12*1 or B279A9A*2 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

*1: for M15A-FKS

*2: for 1KR-FE



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for M15A-FKS A
for 1KR-FE B



A

2.CONFIRM MODEL

B

9.CHECK CONNECTION OF CONNECTOR
2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

3.CHECK CONNECTION OF CONNECTOR

B

6.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

b.

Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

OK:

Connectors are properly connected.



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

B574558C04
2.177,0.052 2.604,0.302 0.427,0.25 1.667,1.5 1.833,1.5 1.833,1.5 1.948,0.625 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 0.219,0.125 0.531,0.281 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.323,3.198 0.479,0.208 10 false GND 2.271,0.104 2.667,0.354 0.396,0.25 10 false H45 1.313,1.417 1.833,1.625 0.521,0.208 10 false EFIO
*a Component with harness connected
Certification ECU (Smart Key ECU Assembly)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
H45-5 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal wavform C



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

Pre-procedure1

a.

Disconnect the A54 ECM connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-61 (IMI) - H45-5 (EFIO) Always Below 1 Ω



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CONNECTION OF CONNECTOR

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

7.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)

NG

CONNECT CONNECTORS PROPERLY

7.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

E446705C04
3.292,0.094 3.719,0.344 0.427,0.25 2.896,1.573 3.083,1.573 3.083,1.573 3.365,0.917 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 0.219,0.125 0.531,0.281 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.323,3.198 0.479,0.208 10 false GND 3.375,0.146 3.688,0.302 0.313,0.156 10 false H67 2.521,1.5 3.042,1.708 0.521,0.208 10 false EFIO
*a Component with harness connected
ID Code Box (Immobiliser Code ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
H67-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal wavform C



A

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

B

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

8.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the A54 ECM connector.


b.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-61 (IMI) - H67-4 (EFIO) Always Below 1 Ω



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CONNECTION OF CONNECTOR

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

b.

Check that the connectors are properly connected to the ECM and ID code box (immobiliser code ECU).

OK:

Connectors are properly connected.



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

10.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)

NG

CONNECT CONNECTORS PROPERLY

10.CHECK ID CODE BOX (IMMOBILISER CODE ECU) (TERMINAL EFIO)
a.

Using an oscilloscope, check the waveform.

E446705C05
3.292,0.094 3.719,0.344 0.427,0.25 2.896,1.573 3.083,1.573 3.083,1.573 3.365,0.917 true 3.583,3.531 3.417,3.531 3.417,3.531 3.417,3.031 true 3.073,3.542 3.24,3.542 3.24,3.542 3.24,3.042 true 0.219,0.125 0.531,0.281 0.313,0.156 10 false *a 3.25,1.969 3.563,2.125 0.313,0.156 10 false *b 2.917,3.469 3.229,3.625 0.313,0.156 10 false *c 3.615,3.469 3.927,3.625 0.313,0.156 10 false *d 0.844,2.99 1.323,3.198 0.479,0.208 10 false GND 3.375,0.146 3.688,0.302 0.313,0.156 10 false H67 2.521,1.5 3.042,1.708 0.521,0.208 10 false EFIO
*a Component with harness connected
ID Code Box (Immobiliser Code ECU)
*b Waveform
*c Approximately 160 ms. *d Approximately 270 ms.


OK:
Tester Connection Condition Tool Setting Specified Condition
H67-4 (EFIO) - Body ground Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after cable disconnected and reconnected to auxiliary battery 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)



Result:
Result Proceed to
11 to 14 V A
Below 1 V B
Normal wavform C



A

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)

B

11.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

C

11.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)

Pre-procedure1

a.

Disconnect the A55 ECM connector.


b.

Disconnect the H67 ID code box (immobiliser code ECU) connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-42 (IMI) - H67-4 (EFIO) Always Below 1 Ω



Post-procedure1

d.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR