Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › from 2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424992 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IGP Relay Circuit (Outside) Monitor

·

IGP Relay Circuit (Inside) Monitor

·

IGR Relay Circuit (Outside) Monitor

·

IGR Relay Circuit (Inside) Monitor



WIRING DIAGRAM

B574556E09
5.708,1.781 6.323,1.979 0.615,0.198 10 false IGPD 2.198,0.167 3.854,0.677 1.656,0.51 10 false from Auxiliary Battery 2.771,3.021 4.26,3.469 1.49,0.448 10 false IGR-NO. 1 2.76,4.5 4.344,5.052 1.583,0.552 10 false IGR-NO. 2 1.281,2.51 2.375,2.75 1.094,0.24 10 false ECU-IGR NO. 1 1.323,3.99 2.458,4.198 1.135,0.208 10 false ECU-IGR NO. 2 5.5,5.042 7.052,5.792 1.552,0.75 10 false Certification ECU (Smart Key ECU Assembly) 1.813,5.094 3.958,5.385 2.146,0.292 10 false Power Distribution Box Assembly 4.583,1.781 5.198,1.979 0.615,0.198 10 false 4C 4.583,1.583 5.198,1.781 0.615,0.198 10 false 17 4.583,1.208 5.198,1.406 0.615,0.198 10 false 4H 0.865,2.177 1.479,2.375 0.615,0.198 10 false 34 0.854,1.563 1.469,1.76 0.615,0.198 10 false 13 0.854,1.75 1.469,1.948 0.615,0.198 10 false 4D 0.854,3.833 1.469,4.031 0.615,0.198 10 false 4B 0.865,3.656 1.479,3.854 0.615,0.198 10 false 38 2.448,6.51 3.063,6.708 0.615,0.198 10 false 1 3.396,6.51 4.01,6.708 0.615,0.198 10 false 2 3.385,6.125 4,6.323 0.615,0.198 10 false 5 2.448,6.125 3.063,6.323 0.615,0.198 10 false 3 5.5,4.875 6.115,5.073 0.615,0.198 10 false H45 4.635,1.042 5.25,1.24 0.615,0.198 10 false 1 5.698,2.74 6.313,2.938 0.615,0.198 10 false IGRD 2.844,6.906 3.302,7.146 0.458,0.24 10 false IGP 4.583,2.729 5.198,2.927 0.615,0.198 10 false 4B 4.594,2.542 5.208,2.74 0.615,0.198 10 false 11 5.427,1.667 6.042,1.865 0.615,0.198 10 false 24 5.438,2.615 6.052,2.813 0.615,0.198 10 false 11 0.854,2.354 1.469,2.552 0.615,0.198 10 false 4C 0.844,3.115 1.458,3.313 0.615,0.198 10 false 4B 0.844,2.927 1.458,3.125 0.615,0.198 10 false 36

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:
·

If interior verification is unsuccessful, Operation History may be stored.

·

If Operation History has been stored, refer to the Operation History List to determine the detection conditions and narrow down trouble areas.



Body Electrical > Entry&Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 440 62

PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 454
Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 4B and 4C power distribution box assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-24 (IGPD) - 4C-17 Always Below 1 Ω
H45-11 (IGRD) - 4B-11 Always Below 1 Ω
4B-36 - Body ground Always Below 1 Ω
H45-24 (IGPD) or 4C-17 - Other terminals and body ground Always 10 kΩ or higher
H45-11 (IGRD) or 4B-11 - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the H45 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B574625C09
1.354,0.031 1.74,0.25 0.385,0.219 2.094,2.01 1.979,2.01 1.979,2.01 1.688,0.917 true 2.281,1.854 2.167,1.854 2.167,1.854 1.76,0.802 true 1.417,0.052 1.875,0.25 0.458,0.198 10 false H45 2.333,1.771 2.948,1.969 0.615,0.198 10 false IGRD 2.156,1.948 2.771,2.146 0.615,0.198 10 false IGPD 0.188,0.052 0.802,0.25 0.615,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H45-11 (IGRD) - Body ground Ignition switch ACC → Ignition switch ON 1 V or less → 9 V or higher
H45-24 (IGPD) - Body ground Ignition switch ACC → Ignition switch ON 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER SOURCE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER SOURCE)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 4D and 4H power distribution box assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
4H-1 - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for RHD B



A

6.CHECK POWER DISTRIBUTION BOX ASSEMBLY

B

9.CHECK POWER DISTRIBUTION BOX ASSEMBLY
6.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

B574905C05
1.76,0.406 2.135,0.677 0.375,0.271 1.74,2.146 2.115,2.417 0.375,0.271 4.698,0.448 5.073,0.719 0.375,0.271 4.688,2.198 5.063,2.469 0.375,0.271 4.792,0.5 5.104,0.698 0.313,0.198 10 false 4B 1.865,0.458 2.177,0.656 0.313,0.198 10 false 4C 1.844,2.198 2.156,2.396 0.313,0.198 10 false 4D 4.781,2.25 5.094,2.448 0.313,0.198 10 false 4H 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Power Distribution Box Assembly)
- -



c.

Measure the resisitance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-17 - 4D-13 Always Below 1 Ω



d.

Connect the auxiliary battery terminal (+) to the 4C-17 terminal.


e.

Connect the auxiliary battery terminal (-) to the 4B-36 terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4H-1 - 4C-34 Auxiliary battery voltage applied between terminals 4C-17 and 4B-36 Below 1 Ω
4H-1 - 4B-38 Auxiliary battery voltage applied between terminals 4C-17 and 4B-36 Below 1 Ω



g.

Connect the auxiliary battery terminal (+) to the 4B-11 terminal.


h.

Connect the auxiliary battery terminal (-) to the 4B-36 terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4H-1 - 4C-34 Auxiliary battery voltage applied between terminals 4B-11 and 4B-36 Below 1 Ω
4H-1 - 4B-38 Auxiliary battery voltage applied between terminals 4B-11 and 4B-36 Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY- IGP RELAY)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY- IGP RELAY)
a.

Disconnect the 4D power distribution box assembly connector.


b.

Remove the IGP relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-13 - No. 1 engine room relay block assembly IGP relay terminal 1 Always Below 1 Ω
No. 1 engine room relay block assembly IGP relay terminal 2 - Body ground Always Below 1 Ω
4D-13 or No. 1 engine room relay block assembly IGP relay terminal 1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT IGP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT IGP RELAY
a.
C279145C40
2.031,0.625 1.677,0.385 true 2.604,0.688 2.917,0.479 true 2.385,1.135 2.875,1.135 true 2.448,1.635 2.906,1.635 true 0.24,0.667 0.396,0.865 0.156,0.198 10 false 3 1.188,0.677 1.344,0.875 0.156,0.198 10 false 5 0.24,1.198 0.396,1.396 0.156,0.198 10 false 1 1.188,1.219 1.375,1.417 0.188,0.198 10 false 2 1.552,0.26 1.708,0.458 0.156,0.198 10 false 1 2.969,0.344 3.125,0.542 0.156,0.198 10 false 2 2.979,1.073 3.135,1.271 0.156,0.198 10 false 5 3,1.563 3.156,1.76 0.156,0.198 10 false 3 0.281,0.229 0.542,0.438 0.26,0.208 10 false *1
*1 IGP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE IGP RELAY

9.CHECK POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

B574905C05
1.76,0.406 2.135,0.677 0.375,0.271 1.74,2.146 2.115,2.417 0.375,0.271 4.698,0.448 5.073,0.719 0.375,0.271 4.688,2.198 5.063,2.469 0.375,0.271 4.792,0.5 5.104,0.698 0.313,0.198 10 false 4B 1.865,0.458 2.177,0.656 0.313,0.198 10 false 4C 1.844,2.198 2.156,2.396 0.313,0.198 10 false 4D 4.781,2.25 5.094,2.448 0.313,0.198 10 false 4H 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a
*a Component without harness connected
(Power Distribution Box Assembly)
- -



c.

Measure the resisitance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4C-17 - 4D-13 Always Below 1 Ω



d.

Connect the auxiliary battery terminal (+) to the 4C-17 terminal.


e.

Connect the auxiliary battery terminal (-) to the 4B-36 terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4H-1 - 4C-34 Auxiliary battery voltage applied between terminals 4C-17 and 4B-36 Below 1 Ω
4H-1 - 4B-38 Auxiliary battery voltage applied between terminals 4C-17 and 4B-36 Below 1 Ω



g.

Connect the auxiliary battery terminal (+) to the 4B-11 terminal.


h.

Connect the auxiliary battery terminal (-) to the 4B-36 terminal.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4H-1 - 4C-34 Auxiliary battery voltage applied between terminals 4B-11 and 4B-36 Below 1 Ω
4H-1 - 4B-38 Auxiliary battery voltage applied between terminals 4B-11 and 4B-36 Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - IGP RELAY)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - IGP RELAY)
a.

Disconnect the 4D power distribution box assembly connector.


b.

Remove the IGP relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4D-13 - No. 1 engine room relay block assembly IGP relay terminal 1 Always Below 1 Ω
No. 1 engine room relay block assembly IGP relay terminal 2 - Body ground Always Below 1 Ω
4D-13 or No. 1 engine room relay block assembly IGP relay terminal 1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT IGP RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGP RELAY
a.
C279145C40
2.031,0.625 1.677,0.385 true 2.604,0.688 2.917,0.479 true 2.385,1.135 2.875,1.135 true 2.448,1.635 2.906,1.635 true 0.24,0.667 0.396,0.865 0.156,0.198 10 false 3 1.188,0.677 1.344,0.875 0.156,0.198 10 false 5 0.24,1.198 0.396,1.396 0.156,0.198 10 false 1 1.188,1.219 1.375,1.417 0.188,0.198 10 false 2 1.552,0.26 1.708,0.458 0.156,0.198 10 false 1 2.969,0.344 3.125,0.542 0.156,0.198 10 false 2 2.979,1.073 3.135,1.271 0.156,0.198 10 false 5 3,1.563 3.156,1.76 0.156,0.198 10 false 3 0.281,0.229 0.542,0.438 0.26,0.208 10 false *1
*1 IGP Relay


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage applied between terminals 1 and 2 Below 1 Ω
Auxiliary battery voltage not applied between terminals 1 and 2 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE IGP RELAY