Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › from 2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424992 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Additional Key cannot be Registered  


DESCRIPTION

If additional registration is not possible, a malfunction of the electrical key transmitter sub-assembly, certification ECU (smart key ECU assembly), power switch, No. 1 indoor electrical key antenna assembly (front floor), steering lock ECU (steering lock actuator or upper bracket assembly), smart door control receiver assembly*1 or electrical key and TPMS receiver assembly*2 is suspected.

*1: for 5 Pin Type

*2: for 12 Pin Type


CAUTION / NOTICE / HINT

NOTICE:
·

If registration of an electrical key transmitter sub-assembly cannot be performed, refer to Service Bulletin.

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator or upper bracket assembly) or electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output.



HINT:

When additional registration is not possible, freeze frame data may be stored in the certification ECU (smart key ECU assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CHECK FOR INTERMITTENT PROBLEMS


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
NOTICE:

If a malfunction occurs, do not remove/install the vehicle auxiliary battery before checking for DTCs.


OK:

DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (VEHICLE ID DIFFERENCE (KEY REGISTRATION))

NG

2.READ VALUE USING GTS (VEHICLE ID DIFFERENCE (KEY REGISTRATION))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle ID Difference (Key Registration) Status of vehicle ID (key registration) No or Yes No: Vehicle ID normal (key registration)
Yes: Vehicle ID malfunction (key registration)
-
Body Electrical > Entry&Start > Data List
Tester Display
Vehicle ID Difference (Key Registration)
50003 440 24

Result:
Result Proceed to
"No" is displayed A
"Yes" is displayed B



A

3.READ VALUE USING GTS (VEHICLE CONTROL HISTORY (ROB))

B

6.REGISTRATION
3.READ VALUE USING GTS (VEHICLE CONTROL HISTORY (ROB))
a.

Read the Vehicle Control History (RoB) according to the display on the GTS.

Body Electrical > Entry&Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 440 62

b.

Check the freeze frame data.


Registration Function (Reason for Non-operation):
Parameter Name Detection Condition Trouble Area
New Key ID Registration Stopped (Security Access Malfunction) Communication error Communication error between the GTS and key registration server
New Key ID Registration Stopped (Certification ECU Type Malfunction) The electrical key transmitter sub-assembly is not compatible with the certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly)
New Key ID Registration Stopped (Key Type Malfunction 1) The electrical key transmitter sub-assembly is not compatible with the registration mode. Electrical key transmitter sub-assembly
New Key ID Registration Stopped (Key Type Malfunction 2) The electrical key transmitter sub-assembly is not compatible with the certification ECU (smart key ECU assembly). Electrical key transmitter sub-assembly


Result:
Result Proceed to
Vehicle operation history related to operation malfunction does not exist A
"New Key ID Registration Stopped (Security Access Malfunction)" is displayed on the GTS B
"New Key ID Registration Stopped (Certification ECU Type Malfunction)" is displayed on the GTS C
"New Key ID Registration Stopped (Key Type Malfunction 1)" is displayed on the GTS D
"New Key ID Registration Stopped (Key Type Malfunction 2)" is displayed on the GTS



A

4.CHECK ENTRY AND START SYSTEM (for Start Function)

B

PERFORM REREGISTRATION

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

D

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

4.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.


b.
B574582C02
2.083,0.469 2.229,0.271 2.229,0.271 2.365,0.271 true 0.656,0.302 0.802,0.302 0.802,0.302 1.01,0.51 true 0.406,0.25 0.719,0.448 0.313,0.198 10 false *1 2.49,0.198 2.802,0.396 0.313,0.198 10 false *2
*1 Power Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.



Result:
Result Proceed to
The power source mode changes A
The power source mode does not change B



A

5.CHECK STEERING LOCK FUNCTION

B

GO TO ENTRY AND START SYSTEM (for Start Function) (Power Source Mode does not Change to ON (IG and ACC))

5.CHECK STEERING LOCK FUNCTION
a.

Turn the ignition switch to ACC or ON.


b.

Check that the steering unlocks.

HINT:

Check that the communication between the steering lock ECU (steering lock actuator or upper bracket assembly) and certification ECU (smart key ECU assembly) is normal.


OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

6.REGISTRATION

NG

GO TO ENTRY AND START SYSTEM (for Start Function) (Unable to Unlock Steering Wheel (Hybrid Control System cannot Start))

6.REGISTRATION
a.

Using an unregistered electrical key transmitter sub-assembly, perform the additional registration procedure.

HINT:

Refer to Service Bulletin.


OK:

Additional registration can be completed.



Result:
Proceed to
OK
NG



OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (FIRST REGISTERED KEY WAS DEFECTIVE)

NG

7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one and register the electrical key transmitter sub-assemblies.

HINT:

Refer to Service Bulletin.


OK:

All of the electrical key transmitter sub-assemblies could be registered to the new certification ECU (smart key ECU assembly) successfully.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG