Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2020.07–2021.04
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0422141 AUDIO AND VISUAL SYSTEM C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  B158F  AV Signal Stoppage (Low Battery Voltage)  


DESCRIPTION

This DTC is stored when a video or audio signal is interrupted due to auxiliary battery voltage input to the radio and display receiver assembly dropping temporarily.

DTC No. Detection Item DTC Detection Condition Trouble Area
B158F AV Signal Stoppage (Low Battery Voltage) A video or audio signal is interrupted when the auxiliary battery voltage drops
·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E445970E01
0.375,0.615 2.531,0.823 2.156,0.208 10 false from Engine Stop and Start ECU*2 1.073,1.49 2.573,1.698 1.5,0.208 10 false from Auxiliary Battery*1 3.063,1.667 3.552,1.854 0.49,0.188 10 false RADIO 5.073,1.385 5.219,1.563 0.146,0.177 10 false 4 5.26,1.531 5.75,1.719 0.49,0.188 10 false +B1 4.906,2.854 5.396,3.042 0.49,0.188 10 false H79 4.896,3.052 6.604,3.417 1.708,0.365 10 false Radio and Display Receiver Assembly 0.167,3 2.063,3.198 1.896,0.198 10 false *1: w/ Stop and Start System 0.167,3.385 2.063,3.583 1.896,0.198 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK VEHICLE SIGNAL (OPERATION CHECK)

B

6.CHECK VEHICLE SIGNAL (OPERATION CHECK)
2.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E268487

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

Measure the auxiliary battery voltage.

Standard Voltage:

11 to 15.5 V


HINT:

This display is updated once per second.



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
3.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H79-4 (+B1) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E268487

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

Measure the auxiliary battery voltage.

Standard Voltage:

10.5 to 16 V


HINT:

This display is updated once per second.



Result:
Proceed to
OK
NG



OK

7.CLEAR DTC

NG

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
7.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

Result:
Proceed to
NEXT



NEXT

8.CHECK FOR DTC
8.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

END

9.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the H79 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H79-4 (+B1) - Body ground Ignition switch off 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG