This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B278588 | Communication between ECUs connected by LIN Bus off | No communication between steering lock ECU (steering lock actuator or upper bracket assembly) and certification ECU (smart key ECU assembly) for 10 seconds or more. | ·
Certification ECU (smart key ECU assembly) ·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Wire harness or connector |
w/ ID Code Box
w/o ID Code Box
Inspect the fuses for circuits related to this system before performing the following procedure.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Service Bulletin.
Check vehicle type.
| Result | Proceed to |
|---|---|
| w/o ID Code Box | A |
| w/ ID Code Box | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC 278588 is output | A |
| DTC 278588 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H71-7 (B) - Body ground | Ignition switch off | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-5 (LIN) - H46-8 (LIN) | Always | Below 1 Ω |
| H71-5 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H71-5 (LIN) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC 278588 is output | A |
| DTC 278588 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC 278588 is output | A |
| DTC 278588 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H67 ID code box (immobiliser code ECU) connector.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC 278588 is output | A |
| DTC 278588 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H46 certification ECU (smart key ECU assembly) connector.
Disconnect the H67 ID code box (immobiliser code ECU) connector.
Disconnect the H71 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H46-8 (LIN) - H71-5 (LIN) | Always | Below 1 Ω |
| H46-8 (LIN) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG