Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424331 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Engine Stop and Start ECU Communication Stop Mode Communication stop for "Stop and Go/Start" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Engine stop and start ECU branch line or connector

·

Power source circuit of engine stop and start ECU

·

Engine stop and start ECU ground circuit

·

Engine stop and start ECU



WIRING DIAGRAM

C404438E04
1.646,0.448 1.833,0.625 0.188,0.177 10 false 2 1.646,0.979 2.042,1.229 0.396,0.25 10 false 13 0.115,1.51 1.323,2.083 1.208,0.573 10 false H117 0.094,1.688 2.177,1.927 2.083,0.24 10 false No. 6 CAN Junction Connector 5.49,0.354 5.677,0.531 0.188,0.177 10 false 13 5.5,0.885 5.688,1.063 0.188,0.177 10 false 14 5.448,0.552 5.792,0.74 0.344,0.188 10 false H43 5.458,1.094 5.802,1.281 0.344,0.188 10 false H43 5.781,0.563 6.219,0.76 0.438,0.198 10 false CANH 5.781,1.094 6.219,1.292 0.438,0.198 10 false CANL 2.177,1.948 3.563,2.156 1.385,0.208 10 false from Auxiliary Battery 5.542,1.771 5.729,1.948 0.188,0.177 10 false 3 5.458,1.958 5.823,2.135 0.365,0.177 10 false A66 5.792,1.969 6.156,2.146 0.365,0.177 10 false BIN1 4.26,2.125 5,2.313 0.74,0.188 10 false BBC NO. 1 5.438,2.396 5.823,2.573 0.385,0.177 10 false A66 5.458,2.833 5.948,3.021 0.49,0.188 10 false A67 5.781,2.406 6.146,2.583 0.365,0.177 10 false BIN2 5.531,2.198 5.719,2.375 0.188,0.177 10 false 1 4.271,2.563 5.01,2.75 0.74,0.188 10 false BBC NO. 2 2.188,2.396 3.573,2.604 1.385,0.208 10 false from Auxiliary Battery 5.531,2.625 5.719,2.802 0.188,0.177 10 false 1 5.792,2.833 6.156,3.01 0.365,0.177 10 false +B 4.302,3 5.042,3.188 0.74,0.188 10 false EFI NO. 3 1.823,2.813 3.552,3.042 1.729,0.229 10 false from EFI-MAIN NO. 1 Relay 5.5,3.083 5.688,3.26 0.188,0.177 10 false 21 5.448,3.26 5.885,3.448 0.438,0.188 10 false H43 5.781,3.271 6.146,3.448 0.365,0.177 10 false IGR 4.125,3.427 5.271,3.635 1.146,0.208 10 false ECU-IGR NO. 4 2.188,3.25 3.542,3.458 1.354,0.208 10 false from IGR-NO. 1 Relay 2.573,3.688 3.917,3.896 1.344,0.208 10 false from IGP Relay 4.104,3.875 5.313,4.063 1.208,0.188 10 false ECU-IGP NO. 3 5.438,3.708 5.792,3.927 0.354,0.219 10 false H43 5.49,3.51 5.677,3.688 0.188,0.177 10 false 18 5.781,3.719 6.146,3.896 0.365,0.177 10 false IGP 2.531,4.135 3.573,4.354 1.042,0.219 10 false from ACC Relay 4.333,4.302 5.021,4.49 0.688,0.188 10 false ECU-ACC 5.448,4.146 5.969,4.333 0.521,0.188 10 false H43 5.5,3.948 5.688,4.125 0.188,0.177 10 false 19 5.781,4.146 6.146,4.323 0.365,0.177 10 false ACC 5.448,4.583 5.896,4.833 0.448,0.25 10 false A67 5.531,4.385 5.719,4.563 0.188,0.177 10 false 6 5.792,4.583 6.229,4.771 0.438,0.188 10 false DGND 5.531,4.823 5.719,5 0.188,0.177 10 false 8 5.448,5.021 5.854,5.24 0.406,0.219 10 false A66 5.531,5.26 5.719,5.438 0.188,0.177 10 false 2 5.448,5.458 5.917,5.74 0.469,0.281 10 false A66 5.781,5.021 6.219,5.208 0.438,0.188 10 false GND1 5.781,5.469 6.219,5.656 0.438,0.188 10 false GND2 5.313,5.917 7.042,6.125 1.729,0.208 10 false Engine Stop and Start ECU

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ENGINE STOP AND START ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H43-13 (CANH) - H43-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ENGINE STOP AND START ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the A66 and A67 engine stop and start ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-8 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A66-2 (GND2) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
A67-6 (DGND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A66-3 (BIN1) - Body ground Always 9.5 to 14 V
A66-1 (BIN2) - Body ground Always 9.5 to 14 V
A67-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
Ignition switch off Below 1 V
H43-21 (IGR) - Body ground Ignition switch ON 9.5 to 14 V
Ignition switch off Below 1 V
H43-18 (IGP) - Body ground Ignition switch ON 9.5 to 14 V
Ignition switch off Below 1 V
H43-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)