Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0435240 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C14FE14  Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open  


DESCRIPTION

This DTC is stored when the skid control ECU (brake actuator assembly) receives a +B line open signal from the steering sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C14FE14 Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open With the +BS terminal voltage between 9.6 and 16.5 V, a steering sensor power supply circuit malfunction signal is received from the steering sensor.
·

Wire harness or connector

·

Steering sensor


Brake

WIRING DIAGRAM

C401576E15
6.073,0.677 6.688,0.875 0.615,0.198 10 false CANL 0.823,0.698 1.438,0.896 0.615,0.198 10 false CANL 0.802,1.271 1.417,1.469 0.615,0.198 10 false CANH 6.073,1.26 6.688,1.458 0.615,0.198 10 false CANH 0.896,2.344 1.51,2.542 0.615,0.198 10 false BAT 2.021,2.5 3.083,2.823 1.063,0.323 10 false ECU-DCC NO. 1 3.615,2.292 5.208,2.583 1.594,0.292 10 false from Auxiliary Battery 3.563,3.594 5.708,3.948 2.146,0.354 10 false : CAN Communication Line 0.313,4.021 0.927,4.219 0.615,0.198 10 false H39 0.292,4.188 1.385,4.417 1.094,0.229 10 false Steering Sensor 5.552,4.042 6.167,4.24 0.615,0.198 10 false A39 5.563,4.208 7.125,4.583 1.563,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 5.75,0.5 6.083,0.698 0.333,0.198 10 false 19 1.292,0.51 1.604,0.708 0.313,0.198 10 false 8 1.302,1.094 1.615,1.292 0.313,0.198 10 false 3 1.313,3.073 1.625,3.271 0.313,0.198 10 false 6 5.802,1.094 6.135,1.292 0.333,0.198 10 false 5 0.906,3.219 1.521,3.417 0.615,0.198 10 false ESS 1.313,2.198 1.625,2.396 0.313,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC
a.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


b.

Read the DTCs using the GTS.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Result:
Result Proceed to
C14FE14 is not output A
C14FE14 is output B



A

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.

Remove the steering wheel and column cover.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the H39 steering sensor connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H39-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR