SENSOR CHECK USING DEALER MODE (SIGNAL CHECK)
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Signals related to the electronically controlled brake system can be inspected by performing a Dealer Mode (Signal Check) inspection. During the inspection, the display of items determined normal by the skid control ECU changes from incomplete to complete.
During Dealer Mode (Signal Check), the VSC system does not operate regardless of whether the system is normal or a malfunction is detected.
If a sensor is malfunctioning, ABS does not operate and the ABS warning light, brake system warning light (yellow indicator) and slip indicator light illuminate.
When entering Dealer Mode (Signal Check), the skid control ECU (brake actuator assembly) communicates with the forward recognition camera to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Dealer Mode (Signal Check) within 5 seconds of entering Dealer Mode (Signal Check).
Even during Dealer Mode (Signal Check), if there is a system malfunction that causes brake hold control to be prohibited, when the vehicle is under the following conditions and the brake hold switch (electric parking brake switch assembly) is turned on, the brake hold operated indicator light blinks.
Vehicle Conditions:
The driver door is closed.
The driver seat belt is fastened.
Procedure to Enter Dealer Mode (Signal Check)
Put the vehicle in the following conditions:
No one is in the vehicle, or only 1 person is in the vehicle.
Place the vehicle on a level surface with the steering wheel centered.
Check that the shift lever is in P. (for M/T, check that the shift lever is in N.)
Release the parking brake. (for M/T, apply the parking brake.)
Release the brake pedal.
Turn the ignition switch to ON. (Do not start the engine or enter the READY ON state.)
Switch the skid control ECU to Dealer Mode (Signal Check) using the GTS.
| Tester Display |
|---|
| Signal Check |
Turn the ignition switch to ON (READY).
After entering Dealer Mode (Signal Check), maintain Dealer Mode (Signal Check) condition for 5 seconds. If Dealer Mode (Signal Check) is ended before 5 seconds elapse, enter Dealer Mode (Signal Check) again, wait 5 seconds, and then check for DTCs again.
Confirm the system has entered Dealer Mode (Signal Check).
Confirm that the ABS warning light, brake system warning light (yellow indicator) and slip indicator light indicate the Dealer Mode pattern (blinking at 0.25 second intervals).
If the ABS warning light, brake system warning light (yellow indicator) or slip indicator light remains illuminated or does not illuminate when Dealer Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.
When entering Dealer Mode (Signal Check), if the parking brake is engaged, the parking brake indicator light (red) will illuminate, and if the parking brake is not engaged, the parking brake indicator light (red) will blink in the Dealer Mode pattern (blinking at 0.25 second intervals).
Speed Sensor Check
With the steering wheel held straight, accelerate the vehicle to a speed of 45 km/h (28 mph) or more without spinning the wheels.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel or spinning the wheels.
Check that the ABS warning light goes off.
If the sensor check does not complete successfully or a malfunctioning sensor is detected, the ABS warning light indicates the Dealer Mode pattern (blinking at 0.25 second intervals) and the ABS system will not operate.
If the vehicle is driven at 80 km/h (50 mph) or more after the ABS warning light turns off, the speed sensor check will be performed again. In this situation, the ABS warning light will start blinking again.
Stop the vehicle.
End of Sensor Check
If the sensor check completes successfully, the ABS warning light turns off when the vehicle is being driven, and indicates the Dealer Mode pattern (blinking at 0.25 second intervals) when the vehicle is stopped.
When all Dealer Mode (Signal Check) Inspection Items are complete, the sensor check is complete.
If the sensor checks have not completed, the ABS warning light will remain blinking while the vehicle is being driven, and the ABS will not operate.
If any malfunctions are detected during Dealer Mode (Signal Check), the ABS warning light, brake system warning light (yellow indicator) or slip indicator light remains illuminated.
If any DTCs are output or if Dealer Mode (Signal Check) Inspection Items do not complete even after repeated attempts, repair or replace the malfunctioning part.
End of Dealer Mode (Signal Check)
Turn the ignition switch off.
Disconnect the GTS.
Dealer Mode (Signal Check) Inspection Item Chart
| Item Name | Range | Judgment Description | Trouble Area |
|---|---|---|---|
| Output Signal of Front Speed Sensor RH | Incomplete / complete | ·
Check for foreign matter ·
Check the gap between the sensor and rotor |
·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Sensor installation ·
Front speed sensor rotor RH |
| Output Signal of Front Speed Sensor LH | Incomplete / complete | ·
Check for foreign matter ·
Check the gap between the sensor and rotor |
·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Sensor installation ·
Front speed sensor rotor LH |
| Output Signal of Rear Speed Sensor RH | Incomplete / complete | ·
Check for foreign matter ·
Check the gap between the sensor and rotor |
·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Sensor installation ·
Rear speed sensor rotor RH |
| Output Signal of Rear Speed Sensor LH | Incomplete / complete | ·
Check for foreign matter ·
Check the gap between the sensor and rotor |
·
Open or short in speed sensor ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Sensor installation ·
Rear speed sensor rotor LH |
| Change in Output Signal of Front Speed Sensor RH | Incomplete / complete | Check the stability of the sensor input waveform | ·
Front speed sensor RH ·
Front speed sensor rotor RH |
| Change in Output Signal of Front Speed Sensor LH | Incomplete / complete | Check the stability of the sensor input waveform | ·
Front speed sensor LH ·
Front speed sensor rotor LH |
| Change in Output Signal of Rear Speed Sensor RH | Incomplete / complete | Check the stability of the sensor input waveform | ·
Rear speed sensor RH ·
Rear speed sensor rotor RH |
| Change in Output Signal of Rear Speed Sensor LH | Incomplete / complete | Check the stability of the sensor input waveform | ·
Rear speed sensor LH ·
Rear speed sensor rotor LH |
| Learning of Stroke Sensor Zero Point | Incomplete / complete | Check the stroke sensor zero point output value | ·
Open or short in wire harness ·
Improperly connected connector, deformation or corrosion of terminals ·
Brake pedal stroke sensor zero point calibration incomplete ·
Brake pedal stroke sensor assembly |