CHECK BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Disconnect the A34*1 or A35*2 electric brake booster (brake booster with master cylinder assembly) connector and measure the voltage or resistance on the wire harness side.
*1: for LHD
*2: for RHD
| *A | for LHD | *B | for RHD |
| *a | Front view of wire harness connector
(to Electric Brake Booster (Brake Booster with Master Cylinder Assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the electric brake booster (brake booster with master cylinder assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A34-1 (+BS) - Body ground | Electric brake booster (Brake booster with master cylinder assembly) power supply input | Always | 11 to 14 V |
| A34-2 (VSK) - Body ground | Relative displacement sensor (brake booster with master cylinder assembly) power supply output | - | - |
| A34-3 | - | - | - |
| A34-4 (CLIN) - Body ground | Brake control power supply assembly signal input | Approximately 1.5 seconds after turning ignition switch ON | Pulse generation |
| A34-5 | - | - | - |
| A34-6 | - | - | - |
| A34-7 | - | - | - |
| A34-8 (SKG) - Body ground | Relative displacement sensor (brake booster with master cylinder assembly) ground | - | - |
| A34-9 (GND) - Body ground | Electric brake booster (Brake booster with master cylinder assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A34-10 (CA1L) | CAN communication line 1 (L) | - | - |
| A34-11 | - | - | - |
| A34-12 | - | - | - |
| A34-13 | - | - | - |
| A34-14 | - | - | - |
| A34-15 (CTY) - Body ground | Front door courtesy light switch assembly input (for driver side) | Driver door closed → open | 11 to 14 V → Below 1.5 V |
| A34-16 (CA2L) | CAN communication line 2 (L) | - | - |
| A34-17 (CBKP) - Body ground | Brake control power supply assembly power supply input | Ignition switch ON | 8.8 to 14 V |
| A34-18 (CA1H) | CAN communication line 1 (H) | - | - |
| A34-19 | - | - | - |
| A34-20 (IGR) - Body ground | IGR power source input | Ignition switch ON | 11 to 14 V |
| A34-21 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A34-22 (SKS1) | Relative displacement sensor (brake booster with master cylinder assembly) 1 signal input | - | - |
| A34-23 (SKS2) | Relative displacement sensor (brake booster with master cylinder assembly) 2 signal input | - | - |
| A34-24 (CWKP) - Body ground | Brake control power supply assembly signal output | Approximately 1.5 seconds after turning ignition switch ON | Pulse generation |
| A34-25 (CA2H) | CAN communication line 2 (H) | - | - |
| A34-26 | - | - | - |
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A35-1 (+BS) - Body ground | Electric brake booster (Brake booster with master cylinder assembly) power supply input | Always | 11 to 14 V |
| A35-2 (VSK) - Body ground | Relative displacement sensor (brake booster with master cylinder assembly) power supply output | - | - |
| A35-3 | - | - | - |
| A35-4 (CLIN) - Body ground | Brake control power supply assembly signal input | Approximately 1.5 seconds after turning ignition switch ON | Pulse generation |
| A35-5 | - | - | - |
| A35-6 | - | - | - |
| A35-7 | - | - | - |
| A35-8 (SKG) - Body ground | Relative displacement sensor (brake booster with master cylinder assembly) ground | - | - |
| A35-9 (GND) - Body ground | Electric brake booster (Brake booster with master cylinder assembly) ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A35-10 (CA1L) | CAN communication line 1 (L) | - | - |
| A35-11 | - | - | - |
| A35-12 | - | - | - |
| A35-13 | - | - | - |
| A35-14 | - | - | - |
| A35-15 (CTY) - Body ground | Front door courtesy light switch assembly input (for driver side) | Driver door closed → open | 11 to 14 V → Below 1.5 V |
| A35-16 (CA2L) | CAN communication line 2 (L) | - | - |
| A35-17 (CBKP) - Body ground | Brake control power supply assembly power supply input | Ignition switch ON | 8.8 to 14 V |
| A35-18 (CA1H) | CAN communication line 1 (H) | - | - |
| A35-19 | - | - | - |
| A35-20 (IGR) - Body ground | IGR power source input | Ignition switch ON | 11 to 14 V |
| A35-21 (STP) - Body ground | Stop light switch assembly input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → Below 1.5 V |
| A35-22 (SKS1) | Relative displacement sensor (brake booster with master cylinder assembly) 1 signal input | - | - |
| A35-23 (SKS2) | Relative displacement sensor (brake booster with master cylinder assembly) 2 signal input | - | - |
| A35-24 (CWKP) - Body ground | Brake control power supply assembly signal output | Approximately 1.5 seconds after turning ignition switch ON | Pulse generation |
| A35-25 (CA2H) | CAN communication line 2 (H) | - | - |
| A35-26 | - | - | - |
CHECK BRAKE ACTUATOR ASSEMBLY
Disconnect the A39 skid control ECU (brake actuator assembly) connector and measure the voltage or resistance on the wire harness side.
| *a | Front view of wire harness connector
(to skid control ECU (Brake Actuator Assembly)) |
- | - |
The voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.
| Terminal No. (Symbol) | Terminal Description | Condition | Specified Condition |
|---|---|---|---|
| A39-1 (+BM) - Body ground | ABS motor relay power supply input | Always | 11 to 14 V |
| A39-2 | - | - | - |
| A39-3 | - | - | - |
| A39-4 (LBL) - Body ground | Brake fluid level warning switch (Brake master cylinder reservoir assembly) input | - | - |
| A39-5 (CANH) | CAN communication line 1 (H) | - | - |
| A39-6 (SKS1) | Brake pedal stroke sensor 2 signal input | - | - |
| A39-7 (FL-) | Front speed sensor LH (-) signal input | - | - |
| A39-8 | - | - | - |
| A39-9 | - | - | - |
| A39-10 | - | - | - |
| A39-11 (CA2H) | CAN communication line 2 (H) | - | - |
| A39-12 | - | - | - |
| A39-13 | - | - | - |
| A39-14 (GND2) - Body ground | Skid control ECU (brake actuator assembly) 2 ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |
| A39-15 | - | - | - |
| A39-16 | - | - | - |
| A39-17 (VSK) | Brake pedal stroke sensor power supply output | - | - |
| A39-18 | - | - | - |
| A39-19 (CANL) | CAN communication line 1 (L) | - | - |
| A39-20 | - | - | - |
| A39-21 (FR+) | Front wheel speed RH (+) power supply output | - | - |
| A39-22 (RR+) | Rear wheel speed RH (+) power supply output | - | - |
| A39-23 (RL-) | Rear wheel speed LH (-) signal input | - | - |
| A39-24 (FL+) | Front wheel speed LH (+) power supply output | - | - |
| A39-25 (CA2L) | CAN communication line 2 (L) | - | - |
| A39-26 (FR-) | Front wheel speed RH (-) signal input | - | - |
| A39-27 | - | - | - |
| A39-28 | - | - | - |
| A39-29 (SKG) | Brake pedal stroke sensor ground | - | - |
| A39-30 (+BS) - Body ground | ABS solenoid relay power supply | Always | 11 to 14 V |
| A39-31 | - | - | - |
| A39-32 | - | - | - |
| A39-33 (STPO) - Body ground | Stop light control relay (stop light switch assembly) output | Always | 11 to 14 V |
| A39-34 (SP1) | Speed sensor signal output | - | - |
| A39-35 (PKB) - Body ground | Electric parking brake switch (Electric parking brake switch assembly) input | Electric parking brake switch (electric parking brake switch assembly) is pushed → released | Below 1 Ω → 10 kΩ or higher |
| A39-36 (IGR) - Body ground | IGR power source input | Ignition switch ON | 11 to 14 V |
| A39-37 (RR-) | Rear speed sensor RH (-) signal input | - | - |
| A39-38 (CSW) - Body ground | VSC OFF switch input | VSC OFF switch is pushed → released | Below 1 Ω → 10 kΩ or higher |
| A39-39 (RL+) | Rear speed sensor LH (+) power supply output | - | - |
| A39-40 | - | - | - |
| A39-41 (STP) - Body ground | Stop light switch assembly signal input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → 1.5 V or less |
| A39-42 (SKS) | Brake pedal stroke sensor 2 signal input | - | - |
| A39-43 (STP2) - Body ground | Stop light signal input | Stop light switch assembly on → off (Brake pedal depressed → released) | 11 to 14 V → 1.5 V or less |
| A39-44 (HZRI) - Body ground | Brake hold switch (electric parking brake switch assembly) input | Brake hold switch (electric parking brake switch assembly) on → off (Pressed → not pressed) | Below 1 Ω → 10 kΩ or higher |
| A39-45 | - | - | - |
| A39-46 (GND1) - Body ground | Skid control ECU (brake actuator assembly) 1 ground | 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal | Below 1 Ω |