Home › General › MAINTENANCE › M15A-FKS COOLANT › from 2020.07
RM36W0E _V1 General _088300 MAINTENANCE _0421808 M15A-FKS COOLANT A

MAINTENANCE  M15A-FKS COOLANT  REPLACEMENT  


PROCEDURE

Hide 53876A 1.SEPARATE FRONT FENDER LINER LH

a.
A476031

Remove the 2 screws and clip.


b.
A476032

Separate the front fender liner LH.


Hide 2.DRAIN ENGINE COOLANT

CAUTION:
·

When engine coolant is hot, do not remove the radiator cap sub-assembly or the radiator drain cock plug.

·

Fluid and steam may spray out due to high pressure, possibly resulting in burns.

A455817C01
5.969,1.458 5.969,1.125 true 6.229,3.5 5.896,3.5 true 5.896,1.458 6.125,1.656 0.229,0.198 10 true *1 6.229,3.427 6.458,3.625 0.229,0.198 10 true *2
*1 Radiator Cap Sub-assembly *2 Radiator Drain Cock Plug




a.
A476033C01
0.906,1.125 1.271,0.896 true 0.635,1.063 0.854,1.281 0.219,0.219 10 true *a
*a Hose


Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.


b.

Loosen the radiator drain cock plug.


c.

Remove the radiator cap sub-assembly. Then drain the engine coolant.

A455819C01
3.823,4.313 3.99,4.563 3.99,4.563 4.156,4.563 false 3.323,1.875 4.885,0.635 4.885,0.635 5.052,0.635 true 5.115,0.573 5.427,0.771 0.313,0.198 10 false *1 4.198,4.5 4.51,4.698 0.313,0.198 10 false *2
*1 Radiator Cap Sub-assembly *2 Radiator Drain Cock Plug


HINT:

Collect the engine coolant in a container and dispose of it according to the regulations in your area.



d.

Tighten the radiator drain cock plug by hand.


e.

Disconnect the hose from the radiator drain cock.


Hide 3.ADD ENGINE COOLANT

a.
A206788C16
2.729,0.875 3.094,0.552 false 2.781,1.813 2.375,1.563 false 3.146,0.448 3.365,0.677 0.219,0.229 10 false *a 2.865,1.771 3.167,1.969 0.302,0.198 10 false *b 3.083,1.167 3.385,1.354 0.302,0.188 10 false *c
*a Filler Tube End
*b Engine Coolant Level
*c 20 mm


Slowly fill the radiator assembly with engine coolant from the radiator inlet opening. (Engine coolant level should be within 20 mm (0.787 in.) from the filler tube end.)

Standard Capacity:
Item Specified Condition
for TMC Made RHD for CVT 5.1 liters (5.4 US qts, 4.5 Imp. qts)
for Manual Transaxle 5.0 liters (5.3 US qts, 4.4 Imp. qts)
for TMMF Made LHD for CVT 5.04 liters (5.3 US qts, 4.4 Imp. qts)
for Manual Transaxle 4.84 liters (5.1 US qts, 4.3 Imp. qts)
RHD for CVT 5.06 liters (5.3 US qts, 4.5 Imp. qts)
for Manual Transaxle 4.86 liters (5.1 US qts, 4.3 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damaging the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



b.

Remove the reserve tank cap.


c.
A455814C02
2.135,0.781 2.927,0.781 true 2.938,0.698 3.177,0.896 0.24,0.198 10 true *a
*a F Line


Slowly pour engine coolant into the radiator reserve tank until it reaches the F line.


d.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand, and then check the level of the engine coolant.

If the engine coolant level is low, add engine coolant.


e.

Install the radiator cap sub-assembly and reserve tank cap.


f.

Perform the following procedure to set the engine to engine coolant filling mode. [*4]

HINT:

It is necessary to set the engine to engine coolant filling mode to ensure that a certain engine water pump assembly (water inlet housing) speed is maintained in order to circulate engine coolant.


i.
·

for CVT:

Move the shift lever to P.

·

for MT:

Confirm that the parking brake is applied.



ii.

Start the engine.


iii.

Run the engine at 1500 rpm or more for 15 seconds or more.


iv.

Check that the speed of the electric water pump increases when the engine is raced to 3000 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Electric Water Pump Speed
50003 372 211,359
Standard:
Tester Display Condition Specified Condition
Electric Water Pump Speed The engine is being raced to 3000 rpm. When the engine speed increases, the speed of the electric water pump also increases.


NOTICE:
·

for CVT:

Do not move the shift lever from P, or engine coolant filling mode will be canceled.

·

for MT:

Make sure that the vehicle is stationary when performing the procedure. If it is detected that the vehicle is moving, engine coolant filling mode will be canceled.



HINT:

The speed of the engine water pump assembly (water inlet housing) changes in accordance with the engine speed when the engine is being raced in engine coolant filling mode.




g.

After the engine has warmed up, run the engine using the following cycle for at least 7 minutes: at 3000 rpm for 5 seconds, at idle speed for 45 seconds. (Repeat this cycle at least 8 times.)


h.

Squeeze the No. 1 radiator hose and No. 2 radiator hose several times by hand to bleed air from the system.

NOTICE:
·

If the radiator reserve tank runs out of engine coolant just after the engine is started, stop the engine immediately, wait until the engine coolant has cooled down, and then add engine coolant.

·

If the coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.

·

Make sure that the radiator reserve tank still has some engine coolant in it.

·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.

·

If the radiator reserve tank does not have enough engine coolant, perform the following: 1) stop the engine, 2) wait until the engine coolant cools down, and 3) add engine coolant until the radiator reserve tank is filled to the F line.




i.
A455814C01
2.156,0.771 2.938,0.771 true 1.823,1.781 2.604,1.781 true 2.958,0.698 3.188,0.896 0.229,0.198 10 true *a 2.615,1.708 2.844,1.885 0.229,0.177 10 true *b
*a F Line
*b L Line


After the engine has cooled down, check that the engine coolant level is between the F line and L line.

If the engine coolant level is below the L line, add engine coolant to the F line.


Hide 53876A 5.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH.


b.

Install the 2 screws and clip.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)