Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440900 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C14D71C  Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range  


DESCRIPTION

The airbag sensor assembly has a built-in yaw rate and acceleration sensor.

If a power source malfunction signal from the yaw rate and acceleration sensor (airbag sensor assembly) is detected by the skid control ECU (brake booster with master cylinder assembly), DTC C14D71C is stored.

DTC C14D71C may be stored due to an intermittent low power source voltage.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C14D71C Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Wire harness or connector

·

Acceleration sensor (airbag sensor assembly)


Brake

WIRING DIAGRAM

C421676E06
0.813,1.313 1.427,1.51 0.615,0.198 10 false CAFL 6.063,1.333 6.677,1.531 0.615,0.198 10 false CA1L 0.792,0.719 1.406,0.917 0.615,0.198 10 false CAFH 6.052,0.719 6.667,0.917 0.615,0.198 10 false CA1H 0.948,1.948 1.406,2.146 0.458,0.198 10 false IGR 2.125,2.104 3.063,2.396 0.938,0.292 10 false A/BAG-IGR 3.917,1.927 5.365,2.344 1.448,0.417 10 false from IGR-NO. 1 Relay 1,2.563 1.313,2.76 0.313,0.198 10 false E1 1,3.177 1.313,3.375 0.313,0.198 10 false E2 0.063,4.167 2.229,4.552 2.167,0.385 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.073,3.99 0.531,4.188 0.458,0.198 10 false H14 3.49,3.156 5.573,3.635 2.083,0.479 10 false : CAN Communication Line 5.073,4.083 7.125,4.51 2.052,0.427 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.083,3.917 5.542,4.115 0.458,0.198 10 false A38 5.781,1.156 6.094,1.354 0.313,0.198 10 false 42 5.781,0.531 6.094,0.729 0.313,0.198 10 false 43 1.271,0.531 1.583,0.729 0.313,0.198 10 false 26 1.281,1.156 1.594,1.354 0.313,0.198 10 false 27 1.281,1.833 1.594,2.031 0.313,0.198 10 false 36 1.292,2.448 1.604,2.646 0.313,0.198 10 false 33 1.281,3.052 1.594,3.25 0.313,0.198 10 false 32

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the H14 yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H14-36 (IGR) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGP CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H14-33 (E1) - Body ground Always Below 1 Ω
H14-32 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.CLEAR DTC
a.

Reconnect the H14 yaw rate and acceleration sensor (airbag sensor assembly) connector.


b.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC
a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


b.

Check if the same DTC is output.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
C14D71C is not output A
C14D71C is output B



A

B