The airbag sensor assembly has a built-in yaw rate and acceleration sensor.
The skid control ECU (brake booster with master cylinder assembly) receives signals from the hybrid vehicle control ECU, steering sensor, certification ECU (smart key ECU assembly), inverter with converter assembly and yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| U011087 | Lost Communication with Drive Motor Control Module "A" Missing Message | Any of the following is detected:
·
When terminal IGP voltage is 9.5 V or more, data from the inverter with converter assembly cannot be received for 2 seconds or more. ·
When terminal IGP voltage is 9.5 V or more, the condition in which data from the inverter with converter assembly cannot be received once or more within 5 seconds occurs 10 times in succession. |
·
CAN communication line ·
Inverter with converter assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U012587 | Lost Communication With Multi-axis Acceleration Sensor Module Missing Message | Any of the following is detected:
·
Acceleration sensor communication is disabled for 1 second or more. ·
Acceleration sensor communication is disabled once or more per 5 seconds 10 times or more within 60 seconds. |
·
CAN communication line ·
Acceleration sensor (airbag sensor assembly) ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U012687 | Lost Communication with Steering Angle Sensor Module Missing Message | Any of the following is detected:
·
Steering sensor communication is disabled for 1 second or more. ·
Steering sensor communication is disabled once or more per 5 seconds10 times or more within 60 seconds. |
·
CAN communication line ·
Steering sensor ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U015187 | Lost Communication with Restraints Control Module Missing Message | When terminal IGP voltage is 9.5 V or more, data from the airbag sensor assembly cannot be received for 5 seconds or more. | ·
CAN communication line ·
Airbag sensor assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U029387 | Lost Communication with Hybrid/EV Powertrain Control Module Missing Message | Any of the following is detected:
·
When terminal IGP voltage is 9.5 V or more, data from the hybrid vehicle control ECU cannot be received for 2 seconds or more. ·
When terminal IGP voltage is 9.5 V or more, the condition in which data from the hybrid vehicle control ECU cannot be received once or more within 5 seconds occurs 10 times in succession. |
·
CAN communication line ·
Hybrid vehicle control ECU ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U110787 | Lost Communication with Power Management Module Missing Message | Push start switch data is invalid for 3 seconds or more. | ·
CAN communication line ·
Certification ECU (smart key ECU assembly) ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U115087 | Lost Communication with Hybrid Powertrain Control Module (ch2) Missing Message | Any of the following is detected:
·
When terminal IGP voltage is 9.5 V or more, data from the hybrid vehicle control ECU cannot be received for 2 seconds or more. ·
When terminal IGP voltage is 9.5 V or more, the condition in which data from the hybrid vehicle control ECU cannot be received once or more within 5 seconds occurs 10 times in succession. |
·
CAN communication line ·
Hybrid vehicle control ECU ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U130857 | Software Incompatibility with Pre-collision Control Module Invalid / Incompatible Software Component | Either one of the following conditions is met when the information collation starts:
·
The information stored in the skid control ECU and the specification information of the pre-collision system do not match. ·
Communication with the forward recognition camera is not established for 1 second or more. |
·
CAN communication line ·
Forward recognition camera ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U130957 | Software Incompatibility with Clearance Warning Control Module Invalid / Incompatible Software Component | Either one of the following conditions is met when the information collation starts:
·
The information stored in the skid control ECU and the specification information of the clearance warning system do not match. ·
Communication with the clearance warning ECU is not established for 1 second or more. |
·
CAN communication line ·
Clearance warning ECU assembly ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
| U149257 | Software incompatibility with Hybrid/EV Powertrain Control Module Invalid/Incompatible Software Component | The information stored in the skid control ECU and the specification information of the HV/EV system do not match when the information collation starts. | ·
CAN communication line ·
Hybrid vehicle control ECU ·
Skid control ECU (brake booster with master cylinder assembly) |
Brake |
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Check if the same DTC is output.
If CAN communication system DTCs and relevant sensor DTCs are output simultaneously, troubleshoot the relevant sensor DTCs (for the ABS, VSC and/or electronically controlled brake system) after the CAN communication system returns to normal.
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are output. | A |
| DTCs are not output. | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING