Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2020.07
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0440901 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  CALIBRATION  


DESCRIPTION


a.

Refer to the table below and then perform the necessary operation according to the part to be replaced in order to perform calibration.

Parts to be Replaced / Operation Necessary Operation
Skid control ECU (brake actuator assembly) Calibration
Yaw rate and acceleration sensor (airbag sensor assembly) Calibration
Wheel alignment adjustment Calibration



UTILITY ITEMS


Utility Items Main Purpose Link
All Readiness Confirm if DTC judgment has been completed. Refer to calibration
Calibration Enter Dealer Mode (Calibration) and clear the memorized steering sensor zero point, yaw rate and acceleration sensor zero point and system information, and then perform yaw rate and acceleration sensor zero point learning and system information memorization. Refer to calibration
Inspection Mode Enter Inspection Mode which prohibits operation of VSC and TRC. (Click here)
Signal Check Enter Dealer Mode (Signal Check) and perform a signal inspection of the electronically controlled brake system. (Click here)
Vehicle Control History (RoB) View vehicle control history. (Click here)
Reset Memory Clear the memorized steering sensor zero point and yaw rate and acceleration sensor zero point. Refer to calibration


ALL READINESS


HINT:
·

With "All Readiness", you can check whether or not the DTC judgment has been completed by using the GTS.

·

You should check "All Readiness" after simulating malfunction symptoms or for validation after finishing repairs.



a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

f.

Press the DTC clear button.


g.

Turn the ignition switch off.


h.

Start the engine.


i.

Perform the DTC judgment driving pattern to run the DTC judgment.


j.

Operate the GTS to inspect all readiness.

Chassis > Brake > Utility
Tester Display
All Readiness
50005 435 20

k.

Input the DTC to be confirmed.


l.

Check the DTC judgment result.

GTS Display Description
Normal
·

DTC judgment completed

·

System normal


Abnormal
·

DTC judgment completed

·

System abnormal


Incomplete
·

DTC judgment not completed

·

Perform the driving pattern


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

·

Perform the driving pattern



If the judgment result shows Incomplete or N/A, perform the DTC confirmation driving pattern again.



CALIBRATION


NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

·

If the yaw rate and acceleration sensor (airbag sensor assembly) was replaced or reinstalled, perform "Calibration".

·

Perform "Calibration" with the vehicle on a level surface (within 0.25° gradient). Do not vibrate the vehicle or open or close doors during zero point calibration. To avoid vibrations due to idling, do not start the engine.

·

Perform "Calibration" with the tires at the specified air pressures and all 4 wheels in contact with the ground. (Do not perform with the vehicle lifted up or load applied on lift.)



HINT:
·

When entering Dealer Mode (Calibration), the skid control ECU communicates with the forward recognition camera to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Dealer Mode (Calibration) within 5 seconds of entering Dealer Mode (Calibration).

·

Performing the following procedure will perform the yaw rate and acceleration sensor zero point calibration and store system information simultaneously.

·

If yaw rate and acceleration sensor zero point calibration do not complete normally, the slip indicator light illuminates and a DTC is output.



a.

Turn the ignition switch off.


b.

Apply the parking brake.


c.

Check that the shift lever is in P. (for CVT)


d.

Check that the shift lever is in N. (for Manual Transaxle)


e.

Connect the GTS to the DLC3.


f.

Turn the ignition switch to ON.


g.

Check that the steering wheel is centered.


h.

Turn the GTS on.


i.

Switch the skid control ECU (brake actuator assembly) to Calibration using the GTS.

Chassis > Brake > Utility
Tester Display
Calibration
50005 435 4554

j.

Check that the ABS warning light and slip indicator light are in Dealer Mode (Calibration) display (blinking at 0.25-second intervals).

NOTICE:
·

When Dealer Mode (Calibration) is selected when the shift lever is not in P, DTCs C121054 and C051D54 are stored. (for CVT)

·

When Dealer Mode (Calibration) is selected with the shift lever is not in N and the parking brake is not applied, DTCs C121054 and C051D54 are stored. (for Manual Transaxle)



HINT:
·

When "Calibration" completes normally, the ABS warning light and slip indicator light are in Dealer Mode (Calibration) display (blinking at 0.25-second intervals).

·

The slip indicator light may illuminate for approximately 7 seconds until "Calibration" completes normally.

·

When entering Dealer Mode (Calibration), if the parking brake is engaged, the parking brake indicator light (red) will illuminate, and if the parking brake is not engaged, the parking brake indicator light (red) will blink in the Dealer Mode pattern (blinking at 0.25 second intervals).

·

Do not exit Dealer Mode (calibration) within 5 seconds of entering Dealer Mode (Calibration). If Dealer Mode (calibration) is exited within 5 seconds of entering Dealer Mode (calibration), DTC U023A87 may be stored. If DTC U023A87 is output after exiting Dealer Mode (Calibration), enter Dealer Mode (Calibration) again, wait at least 5 seconds, then recheck for DTCs.




k.

Turn the ignition switch off and disconnect the GTS.



RESET MEMORY


NOTICE:

After performing "Reset Memory", make sure to perform "Calibration".


a.

Turn the ignition switch off.


b.

Apply the parking brake.


c.

Check that the shift lever is in P. (for CVT)


d.

Check that the shift lever is in N. (for Manual Transaxle)


e.

Connect the GTS to the DLC3.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Select the skid control ECU (brake actuator assembly) to Reset Memory using the GTS.

Chassis > Brake > Utility
Tester Display
Reset Memory
50005 435 4560
NOTICE:
·

If the ignition switch is turned to ON for more than 15 seconds with the shift lever in P after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, DTC C051D54 will be stored. (for CVT)

·

If the ignition switch is turned to ON for more than 15 seconds with the shift lever in N and the parking brake applied after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, DTC C051D54 will be stored. (for Manual Transaxle)

·

When the vehicle is driven with the zero point cleared, the yaw rate and acceleration sensor zero point calibration incomplete DTC is stored.




i.

Turn the ignition switch off.