Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2020.07
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421654 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

B360751C05
0.688,0.083 1,0.24 0.313,0.156 10 false *a 2.5,0.083 2.813,0.24 0.313,0.156 10 false *b
*a Centering Bolt
*b Standard Bolt


HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.

·

Centering bolts are used to install the door hinges to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts when making adjustments.

·

The specified torque for standard bolts is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67003 1.INSPECT REAR DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas "A" to "M" are within the standard ranges.

B584315N01
6.219,1.417 6.375,1.615 0.156,0.198 10 false A 5.313,0.427 5.469,0.625 0.156,0.198 10 false B 5.177,1 5.333,1.198 0.156,0.198 10 false C 3.427,0.344 3.583,0.542 0.156,0.198 10 false D 3.667,1.146 3.823,1.344 0.156,0.198 10 false E 1.281,0.844 1.438,1.042 0.156,0.198 10 false F 1.052,2.771 1.208,2.969 0.156,0.198 10 false H 0.615,3.01 0.771,3.208 0.156,0.198 10 false I 4.198,4.24 4.354,4.438 0.156,0.198 10 false J 4.188,3.552 4.344,3.75 0.156,0.198 10 false K 0.698,1 0.854,1.198 0.156,0.198 10 false G 5.99,3.052 6.146,3.25 0.156,0.198 10 false L 6.24,3.813 6.396,4.01 0.156,0.198 10 false M

Standard Clearance:
Area Measurement Area Measurement
A 2.8 to 5.8 mm (0.110 to 0.228 in.) B 3.3 to 6.3 mm (0.130 to 0.248 in.)
C 1.2 to 5.2 mm (0.0472 to 0.205 in.) D 3.5 to 6.5 mm (0.138 to 0.256 in.)
E 1.2 to 5.2 mm (0.0472 to 0.205 in.) F 3.5 to 6.5 mm (0.138 to 0.256 in.)
G -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) H 3.8 to 6.2 mm (0.150 to 0.244 in.)
I -1.2 to 1.2 mm (-0.0472 to 0.0472 in.) J 6.0 mm (0.236 in.)
K 2.8 mm (0.110 in.) L 2.8 to 5.8 mm (0.110 to 0.228 in.)
M -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) - -



Hide 67003 2.ADJUST REAR DOOR PANEL SUB-ASSEMBLY

a.
B584316

Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

SST
09812-00010  


b.

Tighten the 4 hinge bolts on the vehicle body after adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B584317

Loosen the 4 hinge bolts on the door and adjust the door position.


d.

Tighten the 4 hinge bolts on the door after adjustment.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.
B584318

Using a T40 "TORX" socket wrench, slightly loosen the 2 striker mounting screws.


f.

Using a brass bar and a hammer, hit the striker to adjust its position.


g.

Using a T40 "TORX" socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)