Home › Drivetrain › K320 (MULTIDRIVE / CVT) › PARK / NEUTRAL POSITION SWITCH › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422064 PARK / NEUTRAL POSITION SWITCH A

K320 MULTIDRIVE / CVT  PARK / NEUTRAL POSITION SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the park/neutral position switch assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 7.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 33820B 8.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C429227C03
1.698,2.521 2.031,2.146 false 2.063,2.073 2.375,2.229 0.313,0.156 10 false *1 2.969,3.323 3.281,3.479 0.313,0.156 10 false *a
*1 Clip
*a 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


b.
C429228

Remove the clip to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.


Hide 84540 9.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C429229

Disconnect the park/neutral position switch assembly connector.


b.
C429230C02
1.365,1.073 1.75,1.073 true 1.771,0.958 1.969,1.188 0.198,0.229 10 true *a
*a Piece of Wood or Equivalent


Using a piece of wood or equivalent to secure the transmission control shaft lever to prevent it from rotating, remove the nut, washer and transmission control shaft lever from the manual valve lever shaft.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is not secured when loosening the nut, the manual valve link lever sub-assembly may separate from the manual valve.



c.
C429231

Remove the 2 bolts and park/neutral position switch assembly from the continuously variable transaxle assembly.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.