Home › Drivetrain › K320 (MULTIDRIVE / CVT) › TCM › from 2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422070 TCM A

K320 MULTIDRIVE / CVT  TCM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the TCM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of TCM
If transaxle compensation code read from TCM:
1.

Transfer transaxle compensation code

2.

Perform reset memory

3.

CVT oil pressure calibration

4.

Perform road test to allow TCM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
If transaxle compensation code not read from TCM:
1.

Reset transaxle compensation code

2.

Perform reset memory

3.

CVT oil pressure calibration

4.

Perform road test to allow TCM to learn


Update ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 51451A 3.REMOVE CENTER ENGINE UNDER COVER

Hide 51442C 4.REMOVE ENGINE UNDER COVER LH

Hide 5.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 89535B 9.REMOVE TCM

a.
C434368

Disengage the clamp to disconnect the engine wire from the No. 2 transmission control ECU bracket.


b.
C429249C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claw, rotate the lever and disconnect the TCM connector.


c.
C429250

Remove the 2 bolts and TCM from the continuously variable transaxle assembly.


Hide 89539M 10.REMOVE NO. 1 TRANSMISSION CONTROL ECU BRACKET

a.
C429251

Remove the 2 screws and No. 1 transmission control ECU bracket from the TCM.


Hide 89539N 11.REMOVE NO. 2 TRANSMISSION CONTROL ECU BRACKET

a.
C429252

Remove the 2 screws and No. 2 transmission control ECU bracket from the TCM.