Home › Engine / Hybrid System › G16E-GTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.09
RM36W0E _51 Engine / Hybrid System _095127 G16E-GTS ENGINE CONTROL _0447206 SFI SYSTEM U

G16E-GTS ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A468608E01
3.833,0.333 4.25,0.583 0.417,0.25 1.833,0.333 2.25,0.583 0.417,0.25 5.417,0.333 5.833,0.583 0.417,0.25 1.885,0.385 2.5,0.583 0.615,0.198 10 false D104 3.885,0.385 4.5,0.583 0.615,0.198 10 false D105 5.469,0.385 6.083,0.583 0.615,0.198 10 false A106

HINT:

The standard voltage, resistance and waveform between each pair of the ECM terminals is shown in the table below. The appropriate conditions for checking each pair of the terminals are also indicated. The result of checks should be compared with the standard voltage, resistance and waveform for each pair of the terminals as displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
A106-1(BATT) - A106-10(E1) Battery (for measuring battery voltage and ECM memory) Always 11 to 14 V
A106-2(IGP) - A106-10(E1) Ignition switch signal Ignition switch ON 11 to 14 V
A106-6(FPC) - A106-10(E1) Fuel pump control Engine stopped, ignition switch ON 0 to 1.5 V
A106-8(CANH) - A106-10(E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 1)
A106-9(+B) - A106-10(E1) Power source of ECM Ignition switch ON 11 to 14 V
A106-10(E1) - Body ground Ground Always Below 1 Ω
A106-13(IGR) - A106-10(E1) Ignition signal Ignition switch ON 11 to 14 V
A106-15(MREL) - A106-10(E1) EFI-MAIN NO. 1 relay operation signal Engine stopped, ignition switch ON 0 to 1.5 V
A106-16(NEO) - A106-10(E1) Engine speed signal sent to other ECUs Idling with warm engine Pulse generation
(See waveform 2)
A106-18(CANL) - A106-10(E1) CAN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 3)
A106-21(STP) - A106-10(E1) Stop light switch assembly signal Brake pedal depressed 7.5 to 14 V
Brake pedal released 0 to 1.5 V
A106-22(ST1-) - A106-10(E1) Stop light switch assembly signal (opposite to STP terminal) Ignition switch ON, brake pedal depressed 0 to 1.5 V
Ignition switch ON, brake pedal released 7.5 to 14 V
A106-23(NSW) - A106-10(E1) Clutch start switch signal Ignition switch ON, clutch pedal fully released 11 to 14 V
Ignition switch ON, clutch pedal depressed Below 3.0 V
A106-30(STA) - A106-10(E1) Starter assembly signal Cranking 6 V or higher
A106-32(RFC) - A106-10(E1) Cooling fan control signal Ignition switch ON, A/C switch on (max cool) Pulse generation
(See waveform 4)
A106-34(IREL) - A106-10(E1) EDU relay operation signal Ignition switch ON 0 to 1.5 V
A106-35(+B2) - A106-10(E1) Power source of ECM Ignition switch ON 11 to 14 V
A106-36(E01) - Body ground Ground Always Below 1 Ω
A106-39(KSW) - A106-10(E1) Key in vehicle signal Ignition switch ON 0 to 3 V
A106-42(SPD) - A106-10(E1) Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 5)
A106-45(EC) - Body ground Ground Always Below 1 Ω
D104-19(+BD1) - A106-10(E1) Power source of ECU (injector driver) Ignition switch ON 11 to 14 V
A106-54(E1D1) - Body ground Ground Always Below 1 Ω
A106-55(VPA) - A106-56(EPA) Accelerator pedal position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
A106-57(VCPA) - A106-56(EPA) Power source of accelerator pedal position sensor (for VPA) Engine stopped, ignition switch ON 4.5 to 5.5 V
A106-58(VPA2) - A106-59(EPA2) Accelerator pedal position sensor signal Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
A106-60(VCP2) - A106-59(EPA2) Power source of accelerator pedal position sensor (for VPA2) Engine stopped, ignition switch ON 4.5 to 5.5 V
D104-4(M-) - A106-10(E1) Throttle actuator operation signal (negative signal) Idling with warm engine Pulse generation
(See waveform 6)
D104-3(M+) - A106-10(E1) Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 7)
D104-1(HA1B) - A106-10(E1) Air fuel ratio sensor (sensor 2) heater operation signal Engine stopped, ignition switch ON 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 8)
D104-2(HA1A) - A106-10(E1) Air fuel ratio sensor (sensor 1) heater operation signal Engine stopped, ignition switch ON 11 to 14 V
Idling with cold engine Pulse generation
(See waveform 8)
D104-14(#2D-) - A106-10(E1) Fuel injector assembly signal (No. 2 cylinder) Idling with warm engine Pulse generation
(See waveform 9)
D104-33(#2D+) - A106-10(E1) Fuel injector assembly signal (No. 2 cylinder) Idling with warm engine Pulse generation
(See waveform 9)
D104-35(#3D+) - A106-10(E1) Fuel injector assembly signal (No. 3 cylinder) Idling with warm engine Pulse generation
(See waveform 9)
D104-16(#3D-) - A106-10(E1) Fuel injector assembly signal (No. 3 cylinder) Idling with warm engine Pulse generation
(See waveform 9)
D104-31(#1D+) - A106-10(E1) Fuel injector assembly signal (No. 1 cylinder) Idling with warm engine Pulse generation
(See waveform 9)
D104-12(#1D-) - A106-10(E1) Fuel injector assembly signal (No. 1 cylinder) Idling with warm engine Pulse generation
(See waveform 9)
D104-10(FP1-) - A106-10(E1) Fuel pump assembly (for high pressure side) signal Idling with warm engine Pulse generation
(See waveform 10)
D104-29(FP1+) - A106-10(E1) Fuel pump assembly (for high pressure side) signal Idling with warm engine Pulse generation
(See waveform 10)
D104-25(OE1+) - D104-26(OE1-) Cam timing oil control solenoid assembly operation signal (for exhaust side) Idling Pulse generation
(See waveform 11)
D104-27(OC1+) - D104-28(OC1-) Cam timing oil control solenoid assembly operation signal (for intake side) Idling Pulse generation
(See waveform 11)
D104-45(PRG) - A106-10(E1) Purge VSV operation signal Engine stopped, ignition switch ON 11 to 14 V
Idling with warm engine, under purge control Pulse generation
(See waveform 12)
D104-70(IGT3) - A106-10(E1) No. 3 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 13)
D104-71(IGT2) - A106-10(E1) No. 2 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 13)
D104-72(IGT1) - A106-10(E1) No. 1 ignition coil assembly signal (ignition signal) Idling with warm engine Pulse generation
(See waveform 13)
D104-62(LIN) - A106-10(E1) LIN communication line Engine stopped, ignition switch ON Pulse generation
(See waveform 14)
D104-65(R) - A106-10(E1) Reverse signal Ignition switch ON, shift lever in R 11 to 14 V
D104-84(VCVG) - A106-10(E1) Power source of mass air flow meter sub-assembly (specific voltage) Ignition switch ON 4.8 to 5.2 V
D104-120(VCPF) - A106-10(E1) Power source of fuel pressure sensor (for low pressure side) (specific voltage) Ignition switch ON 4.75 to 5.25 V
D104-87(VTA2) - D104-110(ETA) Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Accelerator pedal fully depressed (engine running) 4.6 to 5.0 V
D104-88(VCV1) - A106-10(E1) Power source of camshaft position sensor (for intake camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
D104-90(VV1+) - D104-89(VV1-) Camshaft position sensor (for intake camshaft) signal Idling with warm engine Pulse generation
(See waveform 15)
D104-91(EV1+) - D104-114(EV1-) Camshaft position sensor (for exhaust camshaft) signal Idling with warm engine Pulse generation
(See waveform 15)
D104-92(NE+) - D104-115(NE-) Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 16)
D104-97(PR) - D104-73(EPR) Fuel pressure sensor (for high pressure side) signal Idling with warm engine 0.5 to 4.5 V
D104-96(VCPR) - D104-73(EPR) Power source of fuel pressure sensor (for high pressure side) (specific voltage) Ignition switch ON 4.75 to 5.25 V
D104-77(VCPE) - D104-78(EPEO) Power source of engine oil pressure and temperature sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D104-107(VG) - D104-83(E2G) Mass air flow meter sub-assembly signal Ignition switch ON Pulse generation
(See waveform 17)
D104-106(THA) - D104-83(E2G) Intake air temperature sensor (mass air flow meter sub-assembly) signal Idling, intake air temperature 0 to 80°C (32 to 176°F) 0.5 to 3.4 V
D104-121(PFL) - D104-119(EPFL) Fuel pressure sensor (for low pressure side) signal Idling with warm engine 0.57 to 4.88 V
D104-108(VTA1) - D104-110(ETA) Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.6 to 1.1 V
Accelerator pedal fully depressed (engine running) 3.2 to 4.8 V
D104-109(VCTA) - D104-110(ETA) Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D104-111(KNK1) - D104-112(EKNK) Knock control sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 18)
D104-113(VCE1) - A106-10(E1) Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
D104-116(VCNE) - A106-10(E1) Power source of crankshaft position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D104-117(A1B-) - A106-10(E1) Air fuel ratio sensor (sensor 2) signal Ignition switch ON 1.17 to 4.49 V
D104-118(A1B+) - A106-10(E1) Air fuel ratio sensor (sensor 2) signal Ignition switch ON 1.53 to 5.96 V
D104-98(PIM) - D104-76(EPIM) No. 1 turbo pressure sensor signal Ignition switch ON 3.0 to 4.5 V
D104-75(VCPM) - D104-76(EPIM) Power source of No.1 turbo pressure sensor (specific voltage) Ignition switch ON 4.75 to 5.25 V
D104-100(PEO) - D104-78(EPEO) Engine oil pressure sensor (engine oil pressure and temperature sensor) signal Idling with warm engine 0.5 to 4.5 V
D104-101(THEO) - D104-78(EPEO) Engine oil pressure sensor (engine oil pressure and temperature sensor) signal Ignition switch ON 0.54 to 4.86 V
D104-129(THW) - D104-130(ETHW) Engine coolant temperature sensor signal Idling, engine coolant temperature 75 to 100°C (167 to 212°F) 0.2 to 1.0 V
D104-18(+BD3) - A106-10(E1) Power source of ECU (injector driver) Ignition switch ON 11 to 14 V
D104-38(+BD2) - A106-10(E1) Power source of ECU (injector driver) Ignition switch ON 11 to 14 V
D104-49(AICV) - A106-10(E1) Vacuum switching valve for air intake control valve operation signal Ignition switch ON 11 to 14 V
D104-20(ABV) - A106-10(E1) Air by-pass valve assembly operation signal Engine stopped, ignition switch ON 11 to 14 V
Air by-pass valve assembly operating Below 1.5 V
D104-94(A1A-) - A106-10(E1) Air fuel ratio sensor (sensor 1) signal Ignition switch ON 1.17 to 4.49 V
D104-95(A1A+) - A106-10(E1) Air fuel ratio sensor (sensor 1) signal Ignition switch ON 1.53 to 5.96 V
D104-99(THIM) - A106-10(E1) Intake air temperature sensor (No. 1 turbo pressure sensor) signal Idling with warm engine 0 to 5.25 V
D104-82(VCPC) - D104-81(EPIC) Power source of Vacuum sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D104-105(PIC) - D104-81(EPIC) Vacuum sensor signal Idling with warm engine 1.0 to 4.5 V
D104-80(VPTA) - D104-79(EPTA) Power source of No.2 turbo pressure sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
D104-103(PTA) - D104-79(EPTA) No. 2 turbo pressure sensor signal Idling with warm engine 1.0 to 4.5 V
D104-102(THTA) - A106-10(E1) Intake air temperature sensor (No. 2 turbo pressure sensor) signal Idling with warm engine 0 to 5.25 V
D104-50(#30) - A106-10(E1) Port fuel injector assembly signal (No. 3 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 19)
D104-51(#20) - A106-10(E1) Port fuel injector assembly signal (No. 2 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 19)
D104-52(#10) - A106-10(E1) Port fuel injector assembly signal (No. 1 cylinder) Idling with warm engine (Data List item "Injection Mode" displaying "Port") Pulse generation
(See waveform 19)
D104-21(WGV+) - A106-10(E1) Vacuum regulating valve assembly operation signal Vacuum regulating valve assembly operating Pulse generation
D104-22(WGV-) - A106-10(E1) Vacuum regulating valve assembly operation signal Vacuum regulating valve assembly operating Pulse generation
D105-37(PEX)*1 - D105-47(EPEX)*1 Differential pressure sensor signal Ignition switch ON 0.4 to 4.8 V
D105-48(VCPX)*1 - D105-47(EPEX)*1 Power source of differential pressure sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V

*1: w/ Gasoline particulate filter

WAVEFORM 1


A283576E15
3.01,1.396 3.344,1.708 0.333,0.313 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 2


A431371E03
2.833,0.938 3.292,1.135 0.458,0.198 10 false GND

Engine Speed Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 3


A283577E13
3.01,1.365 3.375,1.604 0.365,0.24 10 false GND

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Engine stopped, ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 4


A282867E26
2.76,1.563 3.115,1.792 0.354,0.229 10 false GND

Cooling Fan Control Signal
ECM Terminal Name Between RFC and E1
Tester Range 1 V/DIV., 20 ms/DIV.
Condition Ignition switch ON, A/C switch on (max cool)

HINT:

The duty ratio varies depending on the engine coolant temperature.



WAVEFORM 5


A283573E22
2.833,1.229 3.25,1.531 0.417,0.302 10 false GND

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 6


A245848E79
2.854,1 3.323,1.354 0.469,0.354 10 false GND 0.479,0.625 0.844,0.875 0.365,0.25 10 false M-

Throttle Actuator Operation Signal (Negative Terminal)
ECM Terminal Name Between M- and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 7


A208000E84
2.854,0.99 3.313,1.302 0.458,0.313 10 false GND 0.521,0.656 0.99,0.948 0.469,0.292 10 false M+

Throttle Actuator Operation Signal (Positive Terminal)
ECM Terminal Name Between M+ and E1
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 8


A205412E44
2.688,0.896 3.104,1.24 0.417,0.344 10 false GND

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E1
Between HA1B and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with cold engine


WAVEFORM 9


A405747E02
0.302,0.573 0.76,0.771 0.458,0.198 10 false CH1 0.313,0.938 0.771,1.135 0.458,0.198 10 false CH2 2.781,0.594 3.24,0.792 0.458,0.198 10 false GND 2.771,0.948 3.229,1.146 0.458,0.198 10 false GND

No. 1 (to No. 3) Fuel Injector Assembly Signal
ECM Terminal Name CH1: Between #1D+ and E1
CH2: Between #1D- and E1
CH1: Between #2D+ and E1
CH2: Between #2D- and E1
CH1: Between #3D+ and E1
CH2: Between #3D- and E1
Tester Range 50 V/DIV., 200 μs./DIV.
Condition Idling with warm engine.


WAVEFORM 10


A405748E02
0.26,0.406 1.573,0.698 1.313,0.292 10 false FP1+ 0.271,1.083 1.583,1.375 1.313,0.292 10 false FP1- 2.76,0.438 3.135,0.865 0.375,0.427 10 false GND 2.76,1.104 3.135,1.531 0.375,0.427 10 false GND

Fuel Pump Assembly (for High Pressure Side) Signal
ECM Terminal Name CH1: Between FP1+ and E1
CH2: Between FP1- and E1
Tester Range 20 V/DIV., 500 μs./DIV.
Condition Idling with warm engine, Data List item "Injection Mode" displaying "Direct"


WAVEFORM 11


A283575E13
0.51,1.125 1.021,1.385 0.51,0.26 10 false GND

Cam Timing Oil Control Solenoid Assembly Operation Signal
ECM Terminal Name Between OC1+ and OC1-
Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 12


A218020E07
2.844,0.958 3.156,1.198 0.313,0.24 10 GND

Purge VSV Operation Signal
ECM Terminal Name Between PRG and E1
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling with warm engine, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 13


A458860N01
2.948,0.99 3.406,1.188 0.458,0.198 10 false GND

Ignition Coil Assembly Signal (IGT Signal)
ECM Terminal Name Between IGT (1 to 3) and E1
Tester Range 5 V/DIV, 20 ms/DIV
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 14


A349005E05
2.927,1.906 3.281,2.115 0.354,0.208 10 false GND

LIN Communication Signal (Reference)
ECM Terminal Name Between LIN and E1
Tester Range 2 V/DIV., 10 ms./DIV.
Condition Idling with warm engine


WAVEFORM 15


A368769E04
2.875,0.844 3.333,1.042 0.458,0.198 10 false GND 2.875,1.563 3.333,1.76 0.458,0.198 10 false GND

Camshaft Position Sensor Signal
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 16


A200774E37
2.969,1.177 3.396,1.438 0.427,0.26 10 false GND

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 17


A337204E17
0.115,1.417 0.469,1.615 0.354,0.198 10 false GND

Mass Air Flow Meter Sub-assembly Signal
ECM Terminal Name Between VG and E2G
Tester Range 1 V/DIV., 100 μs./DIV.
Condition Ignition switch ON


WAVEFORM 18


A283572E35
2.615,1 3.115,1.292 0.5,0.292 10 false GND

Knock Control Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up the engine

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




WAVEFORM 19


A287799E16
0.656,1.583 1.115,1.781 0.458,0.198 10 false GND

Port Fuel Injector Assembly Signal
ECM Terminal Name Between #10 (to #30) and E1
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling with warm engine (Data List item "Injection Mode" displaying "Port")

HINT:
·

The wavelength becomes shorter as the engine speed increases.

·

When the port injection injectors are operating, Port is displayed for Injection Mode of the Data List.