If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.
| DTC Code | Component | Fail-Safe Operation | Fail-Safe Deactivation Condition |
|---|---|---|---|
| P001100
P001200 |
VVT system | ·
Intake VVT maximum retarded contact. ·
Boost prohibited. ·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P001500 | VVT system | ·
Exhaust VVT maximum advance contact. ·
Boost prohibited. ·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P001600 | VVT system | ·
Intake VVT maximum retarded contact. ·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P001700 | VVT system | ·
Exhaust VVT maximum advance contact. ·
Idle up (control of combustion worsening). |
Pass condition detected and then ignition switch turned off |
| P006D62 | ·
E.F.I. vacuum sensor assembly ·
Atmospheric pressure sensor (ECM) |
Output power is limited. | Ignition switch off |
| P00CF62
P023511 P023515 |
No. 1 turbo pressure sensor | Boost prohibited. | Pass condition detected |
| P003012
P003013 P101A9E |
Air fuel ratio sensor (sensor 1) heater | The ECM turns off the air fuel ratio sensor (sensor 1) heater. | Ignition switch off |
| P003312
P003314 |
Air by-pass valve assembly | Output power is limited. | Pass condition detected |
| P003612
P003613 P102A9E |
Air fuel ratio sensor (sensor 2) heater | The ECM turns off the air fuel ratio sensor (sensor 2) heater. | Ignition switch off |
| P007A11
P007A15 |
Intake air temperature sensor (No. 2 turbo pressure sensor) | ·
The ECM estimates the intake air temperature to be 45°C (113°F). ·
Output power is limited. |
Pass condition detected |
| P008700
P008800 P123513 |
Fuel pump assembly (for high pressure side) | ·
Output power is limited. ·
Fuel pressure is set to 200 kPa (2 kgf/cm2, 29 psi) |
Ignition switch off |
| P011011
P011015 |
Intake air temperature sensor (mass air flow meter sub-assembly) | ·
Boost prohibited. ·
The ECM estimates the intake air temperature to be 20°C (68°F). |
Pass condition detected and then ignition switch turned off |
| P010012
P010014 |
Mass air flow meter sub-assembly | Boost prohibited. | Pass condition detected and then ignition switch turned off |
| P011511
P011515 |
Engine coolant temperature sensor | ·
The ECM estimates the outlet side engine coolant temperature to be 80°C (176°F). ·
The target engine coolant temperature is set to 82°C. |
Pass condition detected |
| P012011
P012015 P01201C P022011 P022015 P060444 P060647 P060747 P060787 P060D49 P060E49 P065714 P16B09F P210018 P210019 P211172 P211173 P211900 P211904 P211977 P21199B P21352B |
Electronic throttle control system | ·
Boost prohibited. ·
The ECM cuts off throttle actuator current for both bank 1, and the throttle valve is returned to a 8° throttle position by the return spring. ·
The ECM then adjusts the engine output by controlling fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal angle to allow the vehicle to be driven at a low speed*1. |
Pass condition detected and then ignition switch turned off |
| P019011
P019015 |
Fuel pressure sensor (for high pressure) | ·
Output power is limited. ·
Fuel pressure is set to 200 kPa (2 kgf/cm2, 29 psi) |
Ignition switch off |
| P020113
P020213 P020313 P062D13 |
ECM (injector driver) | Fuel cut is performed and then the output is limited when the engine speed is 1000 rpm or more. | Pass condition detected and then ignition switch turned off |
| P023400
P02351C |
Turbocharger system | Boost prohibited. | Ignition switch off |
| P030000
P030027 P030085 P030100 P030200 P030300 *2 |
·
Port fuel injector assembly ·
Direct fuel injector assembly ·
Electronic throttle control system |
When a catalyst-damaging misfire occurs (MIL blinking), the following fail-safe operation is performed for catalyst overheat malfunction prevention.
1.
Under a low load and at a low engine speed: - Fuel cut is performed on the malfunctioning cylinder. 2.
Under a high load and at a high engine speed: - Throttle valve opening angle control is performed. - Fuel cut is performed on all cylinders or the malfunctioning cylinder. |
Pass condition detected and then ignition switch turned off |
| P032511
P032515 |
Knock control sensor | The ECM sets the ignition timing to maximum retard. | Ignition switch off |
| P05042B | Stop light switch assembly | The accelerator pedal opening angle is fixed when there is an accelerator pedal malfunction or history of a malfunction. | Ignition switch off |
| P056014 | ECM +B circuit | Generator command is maintained. | Pass condition detected and then ignition switch turned off |
| P107A11
P107A15 |
No. 2 fuel pressure sensor (for low pressure side) | Fuel pump (for low pressure side) control is maintained. | Ignition switch off |
| P137800 | Pre-ignition | Output is limited in low-speed boost region. | Clear DTC after recovering to normal condition |
| P212012
P212014 P21201C P21201F P212099 P212512 P212514 P21251F P21382B |
Accelerator pedal sensor assembly | The accelerator pedal position sensor has 2 sensor circuits: Main and Sub.
If either circuit malfunctions, the ECM limits the engine output. If both circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. |
Pass condition detected and then ignition switch turned off |
| P21CF13
P21D013 P21D113 |
Port fuel injector assembly | The ECM performs fuel-cut when the engine speed is 2000 rpm or more. | Pass condition detected and then ignition switch turned off |
| P222611
P222615 |
Atmospheric pressure sensor (ECM) | Boost prohibited. | Ignition switch off |
| P223711
P223712 P223713 P223716 P223717 P22371B P225111 P225112 |
Air fuel ratio sensor (sensor 1) | Air fuel ratio sensor (sensor 1) air fuel ratio feedback control is stopped. | Pass condition detected and then ignition switch turned off |
| P22AB11
P22AB12 P22AB13 P22AB16 P22AB17 P22B211 P22B212 |
Air fuel ratio sensor (sensor 2) | ·
Control based on air fuel ratio sensor (sensor 2) air fuel ratio feedback is stopped. ·
The ECM turns off the air fuel ratio sensor (sensor 2) heater. |
Pass condition detected and then ignition switch turned off |
| P23AA73 | Air by-pass valve assembly | Output power is limited. | Pass condition detected and then ignition switch turned off |
| P244B00
P246300 |
Gasoline particulate filter system | Output power is limited. | Ignition switch off |
*1: The vehicle can be driven slowly when the accelerator pedal is depressed firmly and slowly. If the accelerator pedal is depressed quickly, the vehicle may speed up and slow down erratically.
*2: Misfire-related fail-safe operations occur when catalyst overheat malfunctions occur.