Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2020.09–2021.04
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0420309 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B009B87  Left Side Restraints Sensor 5 Missing Message  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B009B87 Left Side Restraints Sensor 5 Missing Message
·

The airbag sensor assembly detects a line short in the side collision sensor LH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects a short to ground in the side collision sensor LH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects a short to B+ in the side collision sensor LH circuit (bus 1) for 2 seconds

·

The airbag sensor assembly detects an open in the side collision sensor LH circuit (bus 1) for 2 seconds

·

No. 2 side airbag sensor LH malfunction*1

·

Side airbag pressure sensor LH malfunction

·

Airbag sensor assembly malfunction


·

Harness or connector

·

No. 2 side airbag sensor LH*1

·

Side airbag pressure sensor LH

·

Airbag sensor assembly


Comes on Does not apply to test/check mode

*1: for 5 Door


WIRING DIAGRAM

for 5 Door:
C430311E01
4.865,2 6.729,2.375 1.865,0.375 10 false Airbag Sensor Assembly 4.875,1.823 5.333,2.01 0.458,0.188 10 false O24 5.375,0.906 6,1.229 0.625,0.323 10 false Interface 1.833,2.521 2.406,2.927 0.573,0.406 10 false Interface 5.083,3.219 5.677,3.583 0.594,0.365 10 false Interface 0.927,2.51 1.49,2.906 0.563,0.396 10 false Element 6.021,3.229 6.594,3.552 0.573,0.323 10 false Element 4.813,0.51 5.531,0.667 0.719,0.156 10 false BBL+ 4.833,1.188 5.417,1.333 0.583,0.146 10 false BBL- 4.552,0.5 5.135,0.865 0.583,0.365 10 false 32 4.542,1.177 4.927,1.417 0.385,0.24 10 false 31 2.552,0.51 2.99,0.75 0.438,0.24 10 false BCL+ 3.021,0.51 3.333,0.75 0.313,0.24 10 false 4 2.583,1.167 3.073,1.333 0.49,0.167 10 false BCL- 3.031,1.177 3.333,1.396 0.302,0.219 10 false 3 2.573,2.781 3.073,2.99 0.5,0.208 10 false BDL+ 3.021,2.771 3.271,2.969 0.25,0.198 10 false 1 2.594,3.458 3.083,3.656 0.49,0.198 10 false BDL- 3.031,3.458 3.281,3.656 0.25,0.198 10 false 2 4.354,2.781 4.667,3 0.313,0.219 10 false 2 4.365,3.458 4.656,3.667 0.292,0.208 10 false 1 4.542,2.792 5.25,2.99 0.708,0.198 10 false BDL+ 4.542,3.469 5.115,3.677 0.573,0.208 10 false BDL- 0.708,4.125 1.875,4.302 1.167,0.177 10 false O3 0.698,4.271 3.25,4.688 2.552,0.417 10 false No. 2 Side Airbag Sensor LH 4.542,4.125 5.021,4.333 0.479,0.208 10 false L1 4.542,4.292 6.958,4.677 2.417,0.385 10 false Side Airbag Pressure Sensor LH

for 3 Door:
B473434E84
4.781,2.917 6.5,3.333 1.719,0.417 10 false Airbag Sensor Assembly 4.781,2.74 5.417,2.917 0.635,0.177 10 false O24 4.823,1.01 5.938,1.438 1.115,0.427 10 false BBL+ 5.49,1.458 6.052,1.885 0.563,0.427 10 false Interface 4.552,1.01 4.75,1.25 0.198,0.24 10 false 32 4.823,1.688 5.938,2.115 1.115,0.427 10 false BBL- 4.552,1.688 4.75,2.083 0.198,0.396 10 false 31 2.604,1.01 3.719,1.438 1.115,0.427 10 false BDL+ 2.615,1.698 3.729,2.125 1.115,0.427 10 false BDL- 3.052,1.01 4.167,1.438 1.115,0.427 10 false 2 3.052,1.698 4.167,2.125 1.115,0.427 10 false 1 1.771,1.458 2.354,1.938 0.583,0.479 10 false Interface 0.771,1.458 1.354,1.854 0.583,0.396 10 false Element 0.552,2.344 1.25,2.542 0.698,0.198 10 false L1 0.552,2.521 3.354,2.906 2.802,0.385 10 false Side Airbag Pressure Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the cable to the auxiliary battery terminal, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 5 Door A
for 3 Door B



A

2.CHECK CONNECTION OF CONNECTORS

B

12.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the side airbag pressure sensor LH and No. 2 side airbag sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS

Pre-procedure1

a.
C422861C02
1.708,0.99 1.708,0.656 false 0.49,0.958 0.719,1.188 0.229,0.229 10 false *1 2.771,0.958 3.083,1.229 0.313,0.271 10 false *2 1.646,0.479 1.969,0.656 0.323,0.177 10 false *3
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Wire Harness


Disconnect the connectors from the side airbag pressure sensor LH and No. 2 side airbag sensor LH.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

4.CHECK WIRE HARNESS (SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WIRE HARNESS (SHORT)
a.
C422842C03
0.646,2.198 1.052,2.448 0.406,0.25 1.708,0.979 1.708,0.729 false 1.25,2.75 1.667,2.333 true 2.167,2.75 1.781,2.333 true 0.479,0.583 0.833,0.906 0.354,0.323 10 false *1 2.75,0.573 3.083,0.917 0.333,0.344 10 false *2 1.635,1 1.875,1.25 0.24,0.25 10 false *3 0.667,1.75 0.917,2 0.25,0.25 10 false *a 1.063,2.792 1.49,3.083 0.427,0.292 10 false BDL+ 0.76,2.25 1.188,2.542 0.427,0.292 10 false O3 2.396,0.583 2.573,0.75 0.177,0.167 10 false A 2.094,0.583 2.26,0.75 0.167,0.167 10 false B 1.24,0.583 1.427,0.75 0.188,0.167 10 false C 0.938,0.583 1.073,0.75 0.135,0.167 10 false D 2.115,2.792 2.542,3.083 0.427,0.292 10 false BDL-
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O3-1 (BDL+) - O3-2 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C422842C03
0.646,2.198 1.052,2.448 0.406,0.25 1.708,0.979 1.708,0.729 false 1.25,2.75 1.667,2.333 true 2.167,2.75 1.781,2.333 true 0.479,0.583 0.833,0.906 0.354,0.323 10 false *1 2.75,0.573 3.083,0.917 0.333,0.344 10 false *2 1.635,1 1.875,1.25 0.24,0.25 10 false *3 0.667,1.75 0.917,2 0.25,0.25 10 false *a 1.063,2.792 1.49,3.083 0.427,0.292 10 false BDL+ 0.76,2.25 1.188,2.542 0.427,0.292 10 false O3 2.396,0.583 2.573,0.75 0.177,0.167 10 false A 2.094,0.583 2.26,0.75 0.167,0.167 10 false B 1.24,0.583 1.427,0.75 0.188,0.167 10 false C 0.938,0.583 1.073,0.75 0.135,0.167 10 false D 2.115,2.792 2.542,3.083 0.427,0.292 10 false BDL-
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O3-1 (BDL+) - Body ground Always 1 MΩ or higher
O3-2 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.
C430310C03
0.844,0.635 1.188,0.854 0.344,0.219 0.75,3.615 1.083,3.833 0.333,0.219 1.74,2.865 1.74,2.479 false 2.135,4.167 1.802,3.76 true 1.833,1.333 1.833,1.188 false 1.25,1.167 1.708,0.729 true 2.417,1.167 1.969,0.729 true 1.292,4.177 1.656,3.75 true 0.552,2.323 1.042,2.771 0.49,0.448 10 false *1 2.719,2.323 3.208,2.792 0.49,0.469 10 false *2 1.771,1.344 2.052,1.542 0.281,0.198 10 false *4 0.646,3.167 1.083,3.479 0.438,0.313 10 false *a 0.646,0.188 0.917,0.5 0.271,0.313 10 false *b 2.385,2.323 2.875,2.792 0.49,0.469 10 false A 2.083,2.323 2.573,2.792 0.49,0.469 10 false B 1.229,2.323 1.375,2.51 0.146,0.188 10 false C 0.927,2.323 1.073,2.521 0.146,0.198 10 false D 1.094,1.177 1.552,1.417 0.458,0.24 10 false BDL- 2.302,1.188 2.75,1.417 0.448,0.229 10 false BDL+ 1.146,4.188 1.667,4.417 0.521,0.229 10 false BDL+ 2.031,4.177 2.531,4.406 0.5,0.229 10 false BDL- 0.823,3.635 1.115,3.854 0.292,0.219 10 false O3 0.938,0.656 1.188,0.875 0.25,0.219 10 false L1 1.688,2.854 2.042,3.052 0.354,0.198 10 false *3
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)
*b Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)


Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O3-1 (BDL+) - O3-2 (BDL-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector C.



OK

7.CHECK WIRE HARNESS (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK WIRE HARNESS (SHORT TO B+)

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.
C422842C03
0.646,2.198 1.052,2.448 0.406,0.25 1.708,0.979 1.708,0.729 false 1.25,2.75 1.667,2.333 true 2.167,2.75 1.781,2.333 true 0.479,0.583 0.833,0.906 0.354,0.323 10 false *1 2.75,0.573 3.083,0.917 0.333,0.344 10 false *2 1.635,1 1.875,1.25 0.24,0.25 10 false *3 0.667,1.75 0.917,2 0.25,0.25 10 false *a 1.063,2.792 1.49,3.083 0.427,0.292 10 false BDL+ 0.76,2.25 1.188,2.542 0.427,0.292 10 false O3 2.396,0.583 2.573,0.75 0.177,0.167 10 false A 2.094,0.583 2.26,0.75 0.167,0.167 10 false B 1.24,0.583 1.427,0.75 0.188,0.167 10 false C 0.938,0.583 1.073,0.75 0.135,0.167 10 false D 2.115,2.792 2.542,3.083 0.427,0.292 10 false BDL-
*1 Side Airbag Pressure Sensor LH
*2 No. 2 Side Airbag Sensor LH
*3 Wire Harness
*a Front view of wire harness connector
(to No. 2 Side Airbag Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O3-1 (BDL+) - Body ground Ignition switch ON Below 1 V
O3-2 (BDL-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

8.CHECK SIDE AIRBAG PRESSURE SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK SIDE AIRBAG PRESSURE SENSOR LH
a.

Connect the connector to the No. 2 side airbag sensor LH.


b.
B529883C13
0.906,1.021 1.156,1.229 0.25,0.208 10 false *1 2.354,1 2.594,1.208 0.24,0.208 10 false *2 2.063,1.021 2.188,1.229 0.125,0.208 10 false A 1.906,1.021 2.031,1.25 0.125,0.229 10 false B 1.438,1.021 1.563,1.24 0.125,0.219 10 false C 1.281,1.021 1.417,1.24 0.135,0.219 10 false D
*1 Side Airbag Pressure Sensor RH
*2 No. 2 Side Airbag Sensor LH


Interchange the side airbag pressure sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

9.CHECK SIDE AIRBAG PRESSURE SENSOR LH
9.CHECK SIDE AIRBAG PRESSURE SENSOR LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009B87 is output A
B009E87 is output B
B009B87 and B009E87 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors.



A

10.CHECK NO. 2 SIDE AIRBAG SENSOR LH

B

C

10.CHECK NO. 2 SIDE AIRBAG SENSOR LH
a.
C422835C02
0.719,0.792 1.073,1.219 0.354,0.427 10 false *1 1.094,0.792 1.24,1.135 0.146,0.344 10 false D 1.25,0.792 1.427,1.125 0.177,0.333 10 false C 1.719,0.792 1.865,1.042 0.146,0.25 10 false B 1.875,0.792 2.052,1.052 0.177,0.26 10 false A 2.323,1.115 2.688,1.406 0.365,0.292 10 false *2
*1 No. 2 Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Interchange the No. 2 side airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

e.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

11.CHECK NO. 2 SIDE AIRBAG SENSOR LH
11.CHECK NO. 2 SIDE AIRBAG SENSOR LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009B87 is output A
B009E87 is output B
B009B87 and B009E87 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the No. 2 side airbag sensor LH and RH to their original positions and connect the connectors.



A

B

C

12.CHECK CONNECTION OF CONNECTORS

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



Procedure1

c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag pressure sensor LH.

OK:

The connectors are properly connected.


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

13.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

13.CHECK CONNECTORS

Pre-procedure1

a.
C422860C02
1.521,0.438 1.521,0.802 false 2.635,1.083 2.938,1.521 0.302,0.438 10 false *2 0.385,0.771 0.667,0.979 0.281,0.208 10 false *1 1.448,0.25 1.75,0.417 0.302,0.167 10 false *3
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness


Disconnect the connectors from the airbag sensor assembly and side airbag pressure sensor LH.


Procedure1

b.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals of the connectors are not deformed or damaged.


Result:
Proceed to
OK
NG



Post-procedure1

c.

None



OK

14.CHECK WIRE HARNESS (SHORT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK WIRE HARNESS (SHORT)
a.
C422854C11
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.313 1.375,2.677 0.396,0.365 10 false L1 2.229,2.865 2.75,3.083 0.521,0.219 10 false BDL+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BDL-
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L1-2 (BDL+) - L1-1 (BDL-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C422854C11
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.313 1.375,2.677 0.396,0.365 10 false L1 2.229,2.865 2.75,3.083 0.521,0.219 10 false BDL+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BDL-
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L1-2 (BDL+) - Body ground Always 1 MΩ or higher
L1-1 (BDL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK WIRE HARNESS (OPEN)

Pre-procedure1

a.
C422892C04
0.823,0.833 1.167,1.063 0.344,0.229 0.958,3.729 1.302,3.958 0.344,0.229 2.125,1.833 2.125,1.698 false 1.563,1.729 2.073,1.302 true 2.417,1.74 2.198,1.313 true 1.667,2.854 1.667,2.521 false 1.5,4.271 1.802,3.844 true 2.333,4.271 1.99,3.844 true 0.625,2.375 0.854,2.646 0.229,0.271 10 false *1 2.51,2.656 2.833,2.833 0.323,0.177 10 false *2 1.615,2.896 1.948,3.146 0.333,0.25 10 false *3 2.063,1.833 2.49,2.229 0.427,0.396 10 false *4 0.677,0.188 1.177,0.688 0.5,0.5 10 false *b 0.708,3.427 1.156,3.813 0.448,0.385 10 false *a 2.188,2.375 2.333,2.583 0.146,0.208 10 false A 1.885,2.375 2,2.583 0.115,0.208 10 false B 1.292,2.375 1.5,2.583 0.208,0.208 10 false C 0.979,2.375 1.167,2.583 0.188,0.208 10 false D 1.031,3.76 1.479,4.146 0.448,0.385 10 false L1 0.875,0.875 1.323,1.26 0.448,0.385 10 false O24 2.354,1.75 2.792,2.021 0.438,0.271 10 false BBL+ 1.333,1.75 1.781,2.135 0.448,0.385 10 false BBL- 2.219,4.281 2.677,4.573 0.458,0.292 10 false BDL+ 1.365,4.281 1.865,4.583 0.5,0.302 10 false BDL-
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)


Using a service wire, connect terminals 32 (BBL+) and 31 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L1-2 (BDL+) - L1-1 (BDL-) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

c.

Disconnect the service wire from connector B.



OK

17.CHECK WIRE HARNESS (SHORT TO B+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK WIRE HARNESS (SHORT TO B+)

Pre-procedure1

a.

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the ignition switch to ON.


Procedure1

c.
C422854C11
0.896,2.292 1.24,2.521 0.344,0.229 1.49,2.833 1.802,2.448 true 2.344,2.833 1.979,2.448 true 1.646,0.552 1.646,0.302 false 0.563,0.552 0.802,0.833 0.24,0.281 10 false *1 2.698,0.854 3.01,1.188 0.313,0.333 10 false *2 1.583,0.125 1.844,0.292 0.26,0.167 10 false *3 0.708,1.833 1,2.083 0.292,0.25 10 false *a 2.24,0.552 2.385,0.75 0.146,0.198 10 false A 1.885,0.552 2.083,0.833 0.198,0.281 10 false B 1.292,0.552 1.5,0.75 0.208,0.198 10 false C 0.938,0.552 1.125,0.75 0.188,0.198 10 false D 0.979,2.313 1.375,2.677 0.396,0.365 10 false L1 2.229,2.865 2.75,3.083 0.521,0.219 10 false BDL+ 1.281,2.865 1.75,3.083 0.469,0.219 10 false BDL-
*1 Side Airbag Pressure Sensor LH
*2 Airbag Sensor Assembly
*3 Wire Harness
*a Front view of wire harness connector
(to Side Airbag Pressure Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L1-2 (BDL+) - Body ground Ignition switch ON Below 1 V
L1-1 (BDL-) - Body ground Ignition switch ON Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




OK

18.CHECK SIDE AIRBAG PRESSURE SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK SIDE AIRBAG PRESSURE SENSOR LH
a.
C422835C02
0.719,0.792 1.073,1.219 0.354,0.427 10 false *1 1.094,0.792 1.24,1.135 0.146,0.344 10 false D 1.25,0.792 1.427,1.125 0.177,0.333 10 false C 1.719,0.792 1.865,1.042 0.146,0.25 10 false B 1.875,0.792 2.052,1.052 0.177,0.26 10 false A 2.323,1.115 2.688,1.406 0.365,0.292 10 false *2
*1 Side Airbag Pressure Sensor RH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the side airbag pressure sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs
50002 444

f.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

19.CHECK SIDE AIRBAG PRESSURE SENSOR LH
19.CHECK SIDE AIRBAG PRESSURE SENSOR LH

Pre-procedure1

a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


Procedure1

b.

Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes
50001 444
HINT:

Codes other than DTCs B009B87 and B009E87 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
B009B87 is output A
B009E87 is output B
B009B87 and B009E87 are not output C


Post-procedure1

c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



e.

Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors.



A

B

C