Home › Vehicle Interior › DOOR LOCK › FRONT DOOR LOCK (for 3 Door) › from 2020.09
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0447251 FRONT DOOR LOCK(for 3 Door) G

DOOR LOCK  FRONT DOOR LOCK(for 3 Door)  INSPECTION  


PROCEDURE

Hide 69030A 1.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH (w/o Double Locking System)

a.
B566000C02
0.625,2.438 1.125,2.688 0.5,0.25 1.281,3.75 1.417,4.167 true 1.083,3.792 1.083,4.167 true 0.729,3.802 0.667,4.167 true 0.188,2.625 0.5,2.781 0.313,0.156 10 false *a 0.542,0.375 0.854,0.531 0.313,0.156 10 false *b 1.063,0.198 1.375,0.354 0.313,0.156 10 false *c 1.635,0.406 1.948,0.563 0.313,0.156 10 false *d 0.625,4.219 0.938,4.375 0.313,0.156 10 false E 1.083,4.229 1.396,4.385 0.313,0.156 10 false L 1.438,4.229 1.75,4.385 0.313,0.156 10 false UL 0.76,2.49 1.073,2.74 0.313,0.25 10 false K11
*a Component without harness connected
(front door with motor lock assembly RH)
*b Unlock
*c Neutral
*d Lock


Check the resistance of the lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K11-6(L) - K11-8(E) Lock Below 1 Ω
K11-6(L) - K11-8(E) Neutral 10 kΩ or higher
K11-5(UL) - K11-8(E) Unlock Below 1 Ω
K11-5(UL) - K11-8(E) Neutral 10 kΩ or higher


If the result is not as specified, replace the front door with motor lock assembly RH.



b.
B566001C03
1.479,2.958 1.979,3.208 0.5,0.25 1.281,3.896 0.917,3.75 true 2.177,3.885 2.5,3.75 true 1.333,4.5 1.594,4.25 true 2.177,4.49 1.844,4.24 true 0.688,3.083 1,3.24 0.313,0.156 10 false *a 2.24,2.708 2.552,2.865 0.313,0.156 10 false *b 1.292,2.688 1.604,2.844 0.313,0.156 10 false *c 0.771,3.667 1.083,3.823 0.313,0.156 10 false L 2.583,3.667 2.896,3.823 0.313,0.156 10 false UL 2.219,4.5 2.615,4.667 0.396,0.167 10 false LSSR 1.25,4.51 1.563,4.667 0.313,0.156 10 false E 1.615,3.01 1.927,3.167 0.313,0.156 10 false K11
*a Component without harness connected
(front door with motor lock assembly RH)
*b Lock
*c Unlock


Check the door lock motor operation.

i.

Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition
K11-4(L) - Auxiliary battery positive (+)
K11-1(UL) - Auxiliary battery negative (-)
Lock
K11-1(UL) - Auxiliary battery positive (+)
K11-4(L) - Auxiliary battery negative (-)
Unlock


If the result is not as specified, replace the front door with motor lock assembly RH.



c.

Check the operation of the door unlock detection switch. (w/ Smart Entry and Start System)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K11-7(LSSR) - K11-8(E) Lock 10 kΩ or higher
K11-7(LSSR) - K11-8(E) Unlock Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly RH.



Hide 69030A 2.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY RH (w/ Double Locking System)

a.

Check the resistance of the lock and unlock switch.

i.
B595551C01
1.5,3 2,3.25 0.5,0.25 2.156,4.115 2.5,4.115 true 1.646,4.156 1.51,4.417 true 1.969,4.156 2.104,4.417 true 0.104,0.677 0.271,0.823 0.167,0.146 10 false *b 0.698,0.375 0.865,0.521 0.167,0.146 10 false *c 1.313,0.677 1.469,0.823 0.156,0.146 10 false *d 0.917,3.01 1.073,3.167 0.156,0.156 10 false *a 1.458,4.438 1.573,4.583 0.115,0.146 10 false E 2.146,4.438 2.24,4.583 0.094,0.146 10 false L 2.563,4.031 2.854,4.188 0.292,0.156 10 false UL 1.615,3.042 1.99,3.281 0.375,0.24 10 false K11
*a Component without harness connected
(front door with motor lock assembly RH)
*b Unlock
*c Neutral
*d Lock


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K11-6(L) - K11-8(E) Lock Below 1 Ω
K11-6(L) - K11-8(E) Neutral 10 kΩ or higher
K11-5(UL) - K11-8(E) Unlock Below 1 Ω
K11-5(UL) - K11-8(E) Neutral 10 kΩ or higher


If the result is not as specified, replace the front door with motor lock assembly RH.



b.

Check the door lock motor operation.

i.
B595552C01
1.49,3.167 1.99,3.417 0.5,0.25 1.271,3.958 0.906,3.813 true 2.146,3.938 2.469,3.802 true 1.854,3.917 2.531,3.479 true 1.563,3.896 0.969,3.51 true 0.563,3.146 0.875,3.302 0.313,0.156 10 false *a 1.479,2.844 1.792,3 0.313,0.156 10 false *b 0.76,2.396 1.073,2.552 0.313,0.156 10 false *c 0.688,3.74 1,3.896 0.313,0.156 10 false DL 2.552,3.708 2.865,3.865 0.313,0.156 10 false UL 1.604,3.219 1.917,3.375 0.313,0.156 10 false K11 2.594,3.406 2.906,3.563 0.313,0.156 10 false L 0.615,3.427 1.104,3.594 0.49,0.167 10 false UNDL
*a Component without harness connected
(front door with motor lock assembly RH)
*b Lock
*c Unlock


Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition
K11-2(L) - Auxiliary battery positive (+)
K11-1(UL) - Auxiliary battery negative (-)
Lock
K11-1(UL) - Auxiliary battery positive (+)
K11-2(L) - Auxiliary battery negative (-)
Unlock
K11-4(DL) - Auxiliary battery positive (+)
K11-3(UNDL) - Auxiliary battery negative (-)
Sets
K11-3(UNDL) - Auxiliary battery positive (+)
K11-4(DL) - Auxiliary battery negative (-)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double lockingsystem. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double lockingsystem. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door with motor lock assembly RH.



c.

Check the operation of the door unlock detection switch.

i.
B595552C02
1.531,3.177 1.948,3.427 0.417,0.25 1.448,4.292 0.979,4.573 true 1.865,4.281 2.146,4.552 true 1.635,4.313 1.458,4.552 true 1.26,4.26 0.875,4.26 true 0.625,3.271 0.844,3.479 0.219,0.208 10 false *a 1.448,2.813 1.698,3.042 0.25,0.229 10 false *b 0.833,2.396 1.083,2.635 0.25,0.24 10 false *c 1.302,4.5 1.417,4.646 0.115,0.146 10 false E 2.208,4.49 2.615,4.635 0.406,0.146 10 false LSSR 0.521,4.479 0.906,4.625 0.385,0.146 10 false DLSR 0.708,4.167 0.823,4.313 0.115,0.146 10 false E 1.604,3.219 1.948,3.406 0.344,0.188 10 false K11
*a Component without harness connected
(front door with motor lock assembly RH)
*b Lock
*c Unlock


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K11-7(LSSR) - K11-8(E) Lock 10 kΩ or higher
K11-7(LSSR) - K11-8(E) Unlock Below 1 Ω
K11-9(DSSR) - K11-10(E) Sets 10 kΩ or higher
K11-9(DSSR) - K11-10(E) Unsets Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly RH.



Hide 69040A 3.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH (w/o Double Locking System)

a.
B584481C01
2.292,2.438 2.792,2.688 0.5,0.25 2.146,3.792 2.042,4.135 true 2.354,3.792 2.354,4.167 true 2.667,3.781 2.771,4.115 true 1.896,2.573 2.208,2.729 0.313,0.156 10 false *a 2.708,0.271 3.021,0.427 0.313,0.156 10 false *b 2.198,0.146 2.51,0.302 0.313,0.156 10 false *c 1.677,0.292 1.99,0.448 0.313,0.156 10 false *d 2.813,4.083 3.125,4.24 0.313,0.156 10 false E 2.313,4.198 2.625,4.354 0.313,0.156 10 false L 1.885,4.135 2.198,4.292 0.313,0.156 10 false UL 2.396,2.479 2.708,2.729 0.313,0.25 10 false L11
*a Component without harness connected
(front door with motor lock assembly LH)
*b Unlock
*c Neutral
*d Lock


Check the resistance of the lock and unlock switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L11-9(L) - L11-7(E) Lock Below 1 Ω
L11-9(L) - L11-7(E) Neutral 10 kΩ or higher
L11-10(UL) - L11-7(E) Unlock Below 1 Ω
L11-10(UL) - L11-7(E) Neutral 10 kΩ or higher


If the result is not as specified, replace the front door with motor lock assembly LH.



b.
B566003C02
1.521,2.99 1.958,3.229 0.438,0.24 1.313,3.885 0.917,3.667 true 2.167,3.906 2.5,3.667 true 1.458,4.458 1.594,4.24 true 1.99,4.458 1.823,4.24 true 0.833,3.073 1.146,3.229 0.313,0.156 10 false *a 1.167,2.708 1.479,2.865 0.313,0.156 10 false *b 2.104,2.719 2.417,2.875 0.313,0.156 10 false *c 0.802,3.604 0.958,3.802 0.156,0.198 10 false L 2.573,3.583 2.875,3.781 0.302,0.198 10 false UL 1.146,4.5 1.635,4.667 0.49,0.167 10 false LSSR 2.083,4.51 2.229,4.667 0.146,0.156 10 false E 1.625,3.042 1.938,3.198 0.313,0.156 10 false L11
*a Component without harness connected
(front door with motor lock assembly LH)
*b Lock
*c Unlock


Check the door lock motor operation.

i.

Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition
L11-4(L) - Auxiliary battery positive (+)
L11-1(UL) - Auxiliary battery negative (-)
Lock
L11-1(UL) - Auxiliary battery positive (+)
L11-4(L) - Auxiliary battery negative (-)
Unlock


If the result is not as specified, replace the front door with motor lock assembly LH.



c.

Check the operation of the door unlock detection switch. (w/ Smart Entry and Start System)

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L11-7(E) - L11-8(LSSR) Lock 10 kΩ or higher
L11-7(E) - L11-8(LSSR) Unlock Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly LH.



Hide 69040A 4.INSPECT FRONT DOOR WITH MOTOR LOCK ASSEMBLY LH (w/ Double Locking System)

a.
B595553C01
1.51,3.135 2.01,3.385 0.5,0.25 0.875,4 1.25,4 true 2.167,4 2.531,4 true 1.563,3.938 1.25,3.281 true 1.896,3.906 2.208,3.25 true 0.594,3.281 0.781,3.458 0.188,0.177 10 false *a 2.51,2.438 2.677,2.583 0.167,0.146 10 false *c 1.833,2.833 1.99,2.979 0.156,0.146 10 false *b 1.052,3.125 1.354,3.323 0.302,0.198 10 false UL 0.74,3.906 0.833,4.063 0.094,0.156 10 false L 2.573,3.948 2.979,4.094 0.406,0.146 10 false UNDL 2.271,3.063 2.479,3.208 0.208,0.146 10 false DL 1.635,3.177 1.969,3.344 0.333,0.167 10 false L11
*a Component without harness connected
(front door with motor lock assembly LH)
*b Lock
*c Unlock


Check the door lock motor operation.

i.

Apply auxiliary battery voltage to the motor connector and check the operation of the door lock motor.

OK:
Tester Connection Specified Condition
L11-4(L) - Auxiliary battery positive (+)
L11-3(UL) - Auxiliary battery negative (-)
Lock
L11-3(UL) - Auxiliary battery positive (+)
L11-4(L) - Auxiliary battery negative (-)
Unlock
L11-2(DL) - Auxiliary battery positive (+)
L11-1(UNDL) - Auxiliary battery negative (-)
Sets
L11-1(UNDL) - Auxiliary battery positive (+)
L11-2(DL) - Auxiliary battery negative (-)
Unsets


HINT:
·

Move the door lock motor to the lock position and set the double lockingsystem. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double lockingsystem. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the front door with motor lock assembly LH.



b.
B595553C02
1.458,3.167 1.958,3.417 0.5,0.25 0.927,4.531 1.583,4.281 true 0.865,3.875 1.75,4.219 true 2.01,4.281 2.542,4.51 true 2.167,4 2.531,4 true 0.854,3.229 1.042,3.406 0.188,0.177 10 false *a 2.5,2.427 2.667,2.573 0.167,0.146 10 false *c 1.802,2.844 2.01,3.021 0.208,0.177 10 false *b 0.5,4.458 1,4.667 0.5,0.208 10 false LSSR 2.604,4.427 3.104,4.615 0.5,0.188 10 false DSSR 0.698,3.802 0.906,4.01 0.208,0.208 10 false E 2.615,3.938 2.802,4.115 0.188,0.177 10 false E 1.573,3.208 2.073,3.417 0.5,0.208 10 false L11
*a Component without harness connected
(front door with motor lock assembly LH)
*b Lock
*c Unlock


Check the operation of the door unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L11-7(E) - L11-8(LSSR) Lock 10 kΩ or higher
L11-7(E) - L11-8(LSSR) Unlock Below 1 Ω
L11-6(DSSR) - L11-5(E) Sets 10 kΩ or higher
L11-6(DSSR) - L11-5(E) Unsets Below 1 Ω


If the result is not as specified, replace the front door with motor lock assembly LH.